If you have a fixed-in-place cutoff saw (a radial-arm, miter saw, or sawbuck, for example), it can, unlike the table saw, be conveniently positioned against a wall. Don’t set it in a corner, however, as you’ll need space on either side of the blade. Figure into your plan a two-foot-deep, three-foot-wide space for the saw itself and tables or other supports flanking the tool. Allow enough space directly in front of the saw for the operator to be able to comfortably line up and operate the saw.
Sanding concave molding doesn’t have to be difficult. Find a deep socket that fits the contour of your molding. Wrap a piece of sand- paper around the socket and hold it in place with your fingers. Your sanding will be uniform and the delicate edges of the molding won’t round over. — Eric and Cheryl Weltlich. In this video, Travis talks about his favorite sanding tips.
Keep in mind, there are no perfect boards, but try to always use the straighter boards and avoid warping boards. Also, Brandon and I have found that when it comes to picking out lumber at Home Depot and Lowes, they tend to stock up on fresh boards a few days before the weekend starts (so Thursday/Friday). And then, on Sundays and Mondays, the boards are usually really picked over and there isn’t a good selection. Just another tip to keep in mind!
The beauty of a portable A/C unit is that you don’t have to heft it into a window and block off a valuable source of fresh air for keeping paint fumes at bay. Instead, choose a model with a low profile that you can tuck under a table or against a wall when not in use — a model with casters for maximum maneuverability is ideal. Choose a high-powered unit that will condition at least 400 square feet of space and move it where you need it for maximum comfort as you work.
You may want a garage door if you will need to access your shop with large workpieces or tools, or if you or future owners will ever want to use the space to park a vehicle. Garage doors are notoriously drafty, however, so if you think you can live without one you will probably be warmer. Instead, you could opt for out-swinging double doors. In a small shop you can, at a pinch, rip longer lengths of lumber by feeding the material out of either a strategically placed door or window.
For one thing, the rearrange-it-later approach may simply mean that once you’re set up, the haphazard plan becomes the permanent plan, thanks to sheer inertia (it is a pain to move furniture, after all, especially when some of it is as heavy and awkward as workbenches and stationary tools). For another, too little advance planning may mean you buy a power tool that’s too big for your space.
I saw in the March 2019 Vol36,No.1 Iss 259. I have 2 Christian people very close to me that could likely be getting married soon . When I saw the unity cross on page one this would be the perfect gift from a parent. I would like to make it but need the plans. I do not need 3,000 or 60,000 plans I just wish to purchase the plans for the unity cross. I am a beginner so I need detail plans. Please send me information on ordering just the unity cross plans and where to purchase giant Sequoia and white oak woods. Thank you in advance for your help. I need the plans and information before April.
Once the workshop location is determined, it's time to begin planning how to lay it out. First, acknowledge the need to formulate a plan that's realistic in terms of the space allotted. The size of the structure or workspace will place some constraints on how much can be done. Taking into account size limitations, begin fashioning a plan that keeps efficiency in mind.
Clamping mitered edges can be a real hassle because they never seems to line up correctly. The easiest way that I’ve found to get around this process is to use painter’s tape as clamps. First set the pieces so that the outer edges are facing up and tape them edge-to-edge. The flip the pieces over so the beveled edges are facing up and glue them together. Complete the process by taping the last two edges together and let sit until completed. The tape removes easily and the glue won’t attach to the tape, making sanding and finishing very simple. Try this tip with this clever project!
Minor variances are applications to your municipality to suspend a particular by-law to allow your project to proceed, based on common sense or precedents set by other buildings in your area. If your municipal committee of adjustment denies permission because a neighbour voices concern over the development, you would have to appeal the decision to the municipal board of your particular province. In that case, you may be better off looking for another piece of property with an existing structure that you could renovate, more relaxed zoning regula­tions, a larger lot, or more congenial neighbours. 
Hand tools offer your best chance of finding a real bargain. Until the early 20th century, nearly all woodworking was done with hand tools, and their designs and uses have changed little. Most of the high-end planes on today’s market, for example, are just reproductions of the original designs. And because the originals were mass-produced, they are fairly easy to find at rummage sales and antiques stores. (For more information, refer to Matthew Teague’s article, “Buying Old Tools,” in FWW #180).
KHIEM NGUYEN (Age 28, Austin, TX): Inspired by midcentury modern and Japanese design, Nguyen is a true craftsman. His passion for crafting began with photography and led to him becoming an open major in art school so he could "get (his) hands into everything." After college, Nguyen and his fiancée moved to Austin, where they began A & K Woodworking & Design, specializing in furniture and wood crafts.
Well you can only do so much with your given space. These guidelines are just general best-practices, but that certainly doesn’t mean everyone will be able to execute them to the letter. Even I make concessions for my personal situation. And yes, there would be differences in a Festool shop. I imagine everything would simply revolve around an MFT. :)
This self-clamping table saw fence takes only seconds to put on and lets you crank the blade into the fence to create both angled cuts along board edges and extremely thin rip or rabbet cuts. With a hand- or jigsaw, cut pieces from a 1×4, making the inside width of the “L” a hair under the thickness of your saw’s fence. Drill 5/16-in. holes in the L-blocks and plywood fence and join them with two 1/4-in. x 3-in. countersunk machine screws, washers and Wing-Nuts. As always, use extra caution when you’re sawing without a blade guard. Our thanks for this new sawing angle to professional furniture maker George Vondriska. Check out these 16 genius tool hacks you need to know!

Alternately, a detached shop can often be located closer to your property line and offers you a bit more freedom in terms of the type of foundation you can use. It may give you a sense of welcome separation from your home and open up yard space or allow a deck on the back of your house that would otherwise be lost behind your shop. In an urban setting, if you would like to have a wood stove in your shop you may find it more challenging to find an insurance carrier that allows one in an outbuilding. Also, outbuildings can be subject to more stringent height regulations than additions.
Examples of Bronze Age wood-carving include tree trunks worked into coffins from northern Germany and Denmark and wooden folding-chairs. The site of Fellbach-Schmieden in Germany has provided fine examples of wooden animal statues from the Iron Age. Wooden idols from the La Tène period are known from a sanctuary at the source of the Seine in France.
For all of my planning, I must admit there simply was no room in my shop for some tools. I struggled to find a place for my wide jointer and eventually decided against shoehorning it in, instead making a fixture for my router table that joints edges quite well. My scrollsaw, the bulk of my wood supply, and some storage cabinets didn’t make the cut either. These remain in a nearby room.
Sanding concave molding doesn’t have to be difficult. Find a deep socket that fits the contour of your molding. Wrap a piece of sand- paper around the socket and hold it in place with your fingers. Your sanding will be uniform and the delicate edges of the molding won’t round over. — Eric and Cheryl Weltlich. In this video, Travis talks about his favorite sanding tips.
Use the corners — Some machines are perfectly content to live in a corner, including the bandsaw, scrollsaw, disc or combination sander, and lathe (see the illustration). Orienting the lathe’s tailstock end into a corner will leave room for outboard turning. Pulling the bandsaw away from the wall allows the necessary clearance to cut large curved parts, while locating it near a doorway or window permits resawing of long planks.
×