Efficiency does not always increase with experience, because as our woodshops grow older, they sometimes become unnecessarily rearranged or cluttered. And if you’re just now setting up your first woodshop, this shop layout should give you a great starting point. Each picture represents one half of a standard two-car garage. Click on the images for a larger view, and if anything is unclear, ask a question in the comments field!
If a poured cement floor prohibits the installation of plug receptacles flush to the floor and you elect to surface-mount a plug, protect the exposed feed wire. A piece of one-by-four stock with a groove cut in its underside and its top edges chamfered, will pose little more tripping risk than a threshold. However, paint its protective covering a bright color to remind you and any other visitors to your shop of its presence.
The planners did an interesting thing, my friend recalls. Instead of commissioning a hugely expensive study to try to predict the new patterns that would result from the opening of the new buildings, rather than devising an anticipated program and laying out a new scheme, the university’s brain trust decided to let the students and faculty, the lifeblood of the university, shape their own arterial flow.
An interesting variation of this layout is displayed in Jim Tolpin’s shop, shown in the photo at right. Tolpin located his jointer to the left of his table saw, its height low enough to allow panels cut on the saw to pass over the jointer. To save space, his portable planer lives beneath the saw. All three tools are oriented toward the garage-style door, which can be opened to allow long boards to be ripped, jointed, or thickness planed.
Pocket screws create a solid, simple-to-make joint. Because of the size and visibility of the hole, it’s usually located in areas that are concealed or rarely seen (though special plugs can be used to fill the holes.) Craig Sommerfeld, founder of The Kreg Tool Company, is credited with popularizing pocket screw joinery in the 1980s. The company today is the leader in creating the jigs, clamps and screws used to create pocket screw joints. Learn how to use a pocket screw jig in woodworking projects.
I am often surprised at what tools woodworkers don’t use or own, especially when they are some of the few that I find essential. Sometimes it’s just the difference between hand tool and power tool guys, but sometimes it’s just from lack of experience or the fact that they haven’t given it too much thought. Most likely they just buy tools as they need them and never really considered what tools would give them the most bang for the buck.
A little different from the others, the Wood Shop is geared more towards the “self-helper.” Take the three-hour safety class, available every Saturday, to earn your qualification card. You can then utilize the shop to work on your own projects. A wonderful variety of wood working equipment is available for customer usage for a very reasonable fee. Be sure to check out the available classes where you can learn to make pens, boxes, decorative cutting boards and even rocking chairs. We also produce custom order items to include coin holders, specialized plaques and shadow boxes.
I looked around at many versions of Taiwanese drill presses. I ended up purchasing the Ridgid DP15501 15" drill press because I liked the way the quill stop was made, the work light, key storage, and the easy access to the belt change system. This machine was also on sale when I needed it, so that made it a slam dunk. Choose the one that suits you, as they’re all very similar. The table is large enough, and the distance to the column is large enough to allow you to do most anything a small shop needs.
YP - The Real Yellow PagesSM - helps you find the right local businesses to meet your specific needs. Search results are sorted by a combination of factors to give you a set of choices in response to your search criteria. These factors are similar to those you might use to determine which business to select from a local Yellow Pages directory, including proximity to where you are searching, expertise in the specific services or products you need, and comprehensive business information to help evaluate a business's suitability for you. “Preferred” listings, or those with featured website buttons, indicate YP advertisers who directly provide information about their businesses to help consumers make more informed buying decisions. YP advertisers receive higher placement in the default ordering of search results and may appear in sponsored listings on the top, side, or bottom of the search results page.
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strapping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.
Finding affordable lumber has always been a mainstay for woodworkers, and when you tie our dwindling natural resources into the conversation the time is right to look at milling your own lumber. This seven-part weekly video series takes you through how to find lumber, how to operate a sawmill, details on types of sawing methods, stickering and drying and ultimately advice on using a mill as part of a business. Learn what you need to know to understand Milling Your Own Lumber.
A shop geared toward woodworking would have lumber storage located at one corner of the triangle. Storage space for wood — both long pieces and flat plywood pieces — should be adequate. Raised storage, such as racks or shelves mounted on the wall, must be sturdy. Wood storage should also be in close proximity to the stationary tools or machines (table saw, jointer, power planer, etc.) to avoid frequently carrying heavy wood across the span of the workspace. Wood storage should be handy and near the area where the heavy woodworking tasks will take place. Keep in mind that a considerable amount of space will be needed around stationary tools such as a table saws and jointers for manipulating large pieces of raw lumber.
Minor variances are applications to your municipality to suspend a particular by-law to allow your project to proceed, based on common sense or precedents set by other buildings in your area. If your municipal committee of adjustment denies permission because a neighbour voices concern over the development, you would have to appeal the decision to the municipal board of your particular province. In that case, you may be better off looking for another piece of property with an existing structure that you could renovate, more relaxed zoning regulations, a larger lot, or more congenial neighbours.
Set the table saw fence so the blade is centered on the seam, then push the whole thing through the saw. If the board edges are quite bowed or curvy, you may need a second pass. If so, unscrew the cleats, reclamp the boards across the middle center, then screw on the cleats again. The screws ding up the ends of the boards a little, so cut the boards you’re jointing a bit long, then trim 1/2 in. from each end to remove the screw holes.
If your table saw is near a wall and your shop is fairly narrow, positioning the jointer and planer against the opposite wall is reasonable, as shown in option 2 in the illustration. If the shop isn’t long enough to accommodate long workpieces, try to put these machines near an operable doorway, as shown in the illustration and in the photo of Doug Warren’s shop.