When I began to arrange my shop on paper and on the computer screen, I realized that, in a small shop, moving wood is easier than moving machines. So I ignored the idea of setting up the space for workflow—for example, creating adjacent, sequential zones for lumber storage, rough dimensioning, final dimensioning, joinery, and so on. That workflow concept is more appropriate for larger or commercial shops.
The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.
A little different from the others, the Wood Shop is geared more towards the “self-helper.” Take the three-hour safety class, available every Saturday, to earn your qualification card. You can then utilize the shop to work on your own projects. A wonderful variety of wood working equipment is available for customer usage for a very reasonable fee. Be sure to check out the available classes where you can learn to make pens, boxes, decorative cutting boards and even rocking chairs. We also produce custom order items to include coin holders, specialized plaques and shadow boxes.
You have a few options for planning your shop space: The first is simply to photocopy the two-dimensional models and use them to create a scale layout of your shop floor. You also can go to my Web site (www.yda-online.com/shopmodels.htm) and download two-dimensional images of each tool to be used either on paper or on the computer. As a third alternative, you can download the same modeling program I used, and create three-dimensional plans.
For the next step up in convenience, consider adding a dedicated beverage cooler to your workshop as well. Though many people set up an old refrigerator in the garage for extra soda and beer, a dedicated mini-fridge will help you save on electricity, since new models are far more efficient than old ones. You can pack your beverage cooler with your favorite soft drinks for a pick-me-up while you work or use it to store a lunch to enjoy on a break —all without tracking dirt and or grease into your clean kitchen.
Temperature and Moisture Control. If your workshop is to be located in a portion of your house that is already comfortably warm, this will not be an issue. But if you’re converting a barn or shed or an unheated space, especially if you live in a climate where winter temperatures make for cold hands, you’ll need to devise a heating strategy. In some climates, air conditioning is a virtual necessity in hot weather.
After a permit has been issued, the building inspector will want to be notified at various points during your build in order to do a site visit, walk around and inspect the details to make sure that they meet code requirements. These inspections are commonly at the point where excavation work is complete, when the foundation is completed but before back-filling, when framing and all structural work has been done, after the installation of the insulation and vapour barrier, and then a final inspection after everything is complete. You may need to have a separate plumbing inspector if you’re adding or changing plumbing fixtures, and electrical work will need to be inspected by the appropriate electrical inspector (in Ontario, the Electrical Safety Authority). In my experience, inspectors appreciate good work, a clean, safe site, and are willing to work with homeowners and builders to make sure that the work will meet code and will endure.
I agree with all of these tips in a larger shop. In a smaller shop (mine is just under 400-square feet) most things are fairly close together anyway. One of my original principals for shop layout was … how is a machining process performed on a piece of wood? Is the wood stationary while it is machined … or does the wood move through the machine? If the wood is stationary, I have tried to have this set for one side wall of the shop. To be specific, I have four machines in one line with a continuous table to support long pieces that might need cutting from one or all of those machines. The machines in that line are (from left to right) the drill press, the powered miter saw, the square-chisel mortiser and the radial arm saw.
“I do a lot of finish-sanding freehand, without a sandpaper block, so I can smooth edges and get into nooks and crannies. But the finer grits are usually bonded to thinner paper and, at least for me, the paper is too thin and ends up tearing long before the grit wears out. So I apply duct tape to the back of the sandpaper. The sandpaper is still flexible enough to sand a tight radius and it’s far more durable. You can use this super-strong sandpaper like a shoeshine rag.” — Chuck Merchant
I could not consider a 12" jointer, given that the equipment had to be moved down the stairs to my basement, and the cost would blow my budget. What I wanted in an 8" jointer was true tables, a fence that is solid and easy to adjust, a cut depth gauge that is reliable, and long tables that aid in flattening longer bowed planks. I have found that the Taiwanese tools have come a long way in the past 20 years. I purchased the King KC-80FX 8-inch jointer, with lever adjust parallelogram tables. The system arrived in a good state of tune, and the well-written manual includes a full parts list and exploded parts diagrams. The tables were extremely heavy; more about getting things down the stairs later. The jointer is reasonably priced, it runs smoothly and it is well made.
A good portable air conditioner will also remove excess water from the air, which is critical for keeping your stockpile of wood in good shape. Lumber should be stored in dry conditions so it doesn’t warp, so look for efficiency features that allow you to run the unit overnight in the summer as needed —without worrying about blowing up your electricity bills. Other good features to consider include a thermostat and variable settings that allow you to set your workshop temperature to the perfect level for your comfort.
I consider it part of my job to answer emails from my fellow woodworkers. Guild members or not, everyone receives a response. Occasionally, I get a question that requires a very detailed answer and that answer in and of itself would make for a decent blog post. That happened this morning when a Guild member asked me for advice on shop layout. I brainstormed some basic tips that I think apply to nearly all wood shops (at least the ones that incorporate some power tools). Of course, shop layout is something that evolves over time and really comes down to one’s personal preferences and tool choice. But here are some simple rules of thumb that came to mind; some more obvious than others. If you have some tips to add, please do so in the comments!
Let’s be clear about one thing: No workshop is perfect for everyone. If there were, I could simply give you a precise plan to follow with clear dimensions. Every person who comes to the hobby, avocation, or profession of woodworking has his own particular collection of tools and his own peculiar work style, skills, and desires for the kind of woodworking he wants to do that gives him a unique approach as to how he will lay out a shop: where the tools should go, where lumber and supplies are stored, and how much bench area he needs.