When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
Under the Occupational Safety and Health Act of 1970, employers are responsible for providing safe and healthful workplaces for their employees. OSHA's role is to ensure these conditions for America's working men and women by setting and enforcing standards, and providing training, education and assistance. For more information, visit www.osha.gov or call OSHA at 1-800-321-OSHA (6742), TTY 1-877-889-5627.
In general, a table saw requires at least eight feet in front and behind to accommodate standard sheet goods and four feet side to side. A work table should provide four feet clearance on all sides, and pathways between tables, benches and storage units should be three feet wide. Proper clearance will allow you to move about with ease while you work.
A clean well-organized environment is key to staying A clean well-organized environment is key to staying happy. The same goes for your desk. Keep the clutter at bay and organize all of your small essentials with the Dickies Work Gear 57050 Mug Organizer. Designed to fit over most mugs this clever caddy features 8 outer pockets and 6 ... More + Product Details Close
Finally, as I shared in my post last week on how I learned woodworking, I learned how to use power tools by watching YouTube videos and then just trying them out for myself. I highly recommend this method to learn how to use your power tools. There are lots of videos on specific models of tools too. So, watch a few how-to videos and very importantly, review the tool manual and safety guide for your own tools. Then, go ahead and try the tool out yourself and start using it!
There are a few things particleboard is NOT. It’s not medium density fiberboard (MDF)—a material with greater density and weight composed of more uniform particles. It’s NOT oriented strand board (OSB), a material composed of large wood chips and strands that’s structurally equivalent to plywood. It does NOT have great nail or screw holding ability, nor is it all that water resistant; water can quickly cause the material to swell and lose structural integrity. But if you need something flat and cheap for use in a dry place, particleboard will do you proud. Learn how to make a plastic laminate tabletop with a particleboard substrate.
Second, learning how to read lumber dimensions, like knowing what 1×2 or 2×12 actually means, is really important. Understanding softwood lumber dimensions will help you to read woodworking build plans, shop for lumber, and understand the general measurements for your projects. I’ve provided a simple explanation to lumber sizes along with a free lumber size chart printable here!
Natural Light. Natural light is best, so any windows that offer illumination to the space should be put to good use. If you have little sunlight in your shop, locate your workbench so that its work surface gets whatever there is. Even the best eyesight is made better by good light, so the close work to be done on a benchtop benefits from the natural light.
The number of windows, as well as their sizing and placement, depends on your orientation, view, desire for ventilation, and needs for daylight and solar gain. Orienting more of your windows towards the south side of your shop and placing them high enough that they are shaded by the eaves in summer, but allow lower-angle winter light to come in, will increase your ability to get free light and heat from the sun. If your goal is to take advantage of passive solar opportunities, make sure that you carefully research the type of glass that is in your windows and look for something with a high solar heat gain coefficient. Higher windows generally allow for benches and tools beneath them, and relatively windowless north walls may be a place to arrange wood storage or mechanicals.
Hardwoods, botanically known as angiosperms, are deciduous and shed their leaves annually with temperature changes. Softwoods come from trees botanically known as gymnosperms, which are coniferous, cone-bearing, and stay green year round. Although a general pattern, softwoods are not necessarily always “softer” than hardwoods, and vice versa.
If your shop is long and narrow, option 2 provides maximum space to the left of the fence for handling large sheets of plywood. If you often work with full sheets of plywood or other sheet goods, you might want to build the table saw into an extension table surround, as San Diego woodworker Pat Curci did in his small shop (see the photo). The surround offers support for large panels, as well as provides an ample work surface near the saw.