Some of the most important decisions in laying out a shop involve the placement of basic machines, such as the table saw and jointer. Deciding where to put them depends in part on the scale of woodworking you do, which determines the clearance area around these machines if you need to handle long stock or large sheet goods. You’ll also want to consider work flow to avoid an excess amount of running around the shop to accomplish tasks, as well as how to power your machines without turning your shop into a snakepit of extension cords.
I place the band saw first in my order of purchases, because I consider it the heart of the shop. Band saws are very safe tools for ripping, re-sawing, cutting curves and more because all of the force is downward, virtually eliminating any chance of unexpected kickbacks. I wanted a saw that had a strong back, dynamically balanced cast iron wheels for smooth operation and flywheel effect, 12" depth of cut, good dust extraction design, a large table and a solid fence. After shopping around, I settled on the General International Model 90-170 14" saw. It is very smooth, comes with an Excalibur fence, and it is light enough (133kg) to move into your basement without crushing someone.
Cutting thick, rough, warped hardwood can be cumbersome and dangerous. To provide some control over this process, I built a chop-saw station with wings that extend to support long boards. Again, anytime you make something that consumes shop space, make a shelf underneath to gain storage. The chop saw sits in a recess so that the deck of the saw is at the same height as the workstation deck.
Great suggestions for a large workshop where there is floor space… the shop I wish I had!!! My shop is a one car garage 23 X 13, which poses a real problem when it comes to workflow and tool positioning. I use your philosophy in reverse Marc; meaning, all my tools are on casters and I store my tools at one end of the shop in an order that allows me to bring the right tool or two into the centre of the shop to use. Bring the tool to the wood.
From felling the trees through installation of the final piece Scott Wunder, owner of WunderWoods in St. Charles, MO, shares his woodworking knowledge with anyone that will talk to him about wood. Whether you want to learn about milling lumber or need help on a project, get your fill of woodworking infotainment at WunderWoods.com. Scott writes about all aspects of woodworking and specializes in finishing (mostly because no one else likes to sand).
If your shop lacks wall space or doesn’t have a long enough wall to accommodate long stock, another option is to place the crosscut saw near an operable doorway with the right-hand side closest to the door (see option 2 in the illustration). This leaves most of the length of the fence to the left of the blade (preferable if you’re right-handed), allowing short and mid-sized parts to be cut to length or trimmed without having to open the door.
Great info I’m in shop build right now finally after going through the tool purchasing period as I was tired of not having the correct tool for the job I wanted to start. Should be up and organized in a month or so In between baby duties. Wondered if you’d be interested in seeing the finished product and maybe offer some thoughts on how it’s setup it’s always good to have another pair of eyes to spot any problems.
This simple jig makes laying out circles a breeze. Drill a 1/8-in. hole through every inch mark on a ruler or yard-stick. To draw a circle, place a pin through the number “1” into the center of your board. Add 1 in. to the radius of the circle you wish to draw, and insert a pencil into this number. Using the pin as a pivot, rotate the pencil to mark the circle. — Edwin Constantino. How to Cut Curves in Wood
In most small shops, once the key machines are in place, others are arranged wherever there is room for them. There typically isn’t enough free space for these tools in the middle of the floor area, although sometimes you can tuck a machine into an unused space. For example, in a shop where the table saw is in the center, a shaper (or a router table or spindle sander) with a table the same height as the saw can be put on the outfeed side of the extension table (see the illustration). Also, building a router table directly into the table saw’s extension table is a great way to save space, as well as make use of the saw’s fence for routing operations.
The thickness planer—A thickness planer will significantly expand the creativity and craftsmanship of your work by allowing you to buy roughsawn stock and use wood of any thickness in your designs. Nowadays, a new planer often represents a better value than a used model. In recent years, DeWalt and Ridgid have introduced portable planers with chip-ejection fans, which work as a built-in dust collector. Dust collection is important for all tools, but essential for thickness planers. This feature can help delay the expense of a dust collector and thus reduce the overall cost of a planer. Speaking of dust collection, I should mention that I don’t use a dedicated dust collector in my shop. I use a shop vac with a small hose for my sanders and a larger-diameter hose for the tablesaw and router table, and I depend on the built-in chipejection fan for my thickness planer.
One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at $50/sheet.
A clean well-organized environment is key to staying A clean well-organized environment is key to staying happy. The same goes for your desk. Keep the clutter at bay and organize all of your small essentials with the Dickies Work Gear 57012 Mug Organizer. Designed to fit over most mugs this clever caddy features 8 outer pockets and 6 ... More + Product Details Close
That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000.
Sanding small items is tricky, as they’re hard to clamp in a vise to work on them. So instead of bringing the sandpaper to the workpiece, I bring the workpiece to the sandpaper. I glue sheets of sandpaper to a piece of plywood; 60 and 100-grit on one side and 150 and 220-grit on the other. Spray adhesive works well for this. Since there’s sandpaper on both sides, my sanding board doesn’t slide around on the bench. Check out these small projects!
In this video James Huggett shares a very detailed tutorial on how to cut a half-blind dovetail joint with hand tools, for use on drawers and case pieces. Jim has cut many dovetails over the years, and here are some of the lovely dovetailed drawers that Jim has made using this half-blind dovetail joint: Notice the deeply scribed layout line on these drawers. That, along with irregular and more delicate pins, are a sure sign
Rockler Buffalo is proudly hosting the CNC Users Group! The club consists of CNC owners, users and prospective buyers. Every meeting consists of a ‘Show-n-Tell’ portion, demonstration and then a group discussion. We’d be happy to have you join us and we’ll be looking forward to seeing you at the store! Don’t miss out on this one of kind experience.
YP - The Real Yellow PagesSM - helps you find the right local businesses to meet your specific needs. Search results are sorted by a combination of factors to give you a set of choices in response to your search criteria. These factors are similar to those you might use to determine which business to select from a local Yellow Pages directory, including proximity to where you are searching, expertise in the specific services or products you need, and comprehensive business information to help evaluate a business's suitability for you. “Preferred” listings, or those with featured website buttons, indicate YP advertisers who directly provide information about their businesses to help consumers make more informed buying decisions. YP advertisers receive higher placement in the default ordering of search results and may appear in sponsored listings on the top, side, or bottom of the search results page.
If your shop is long and narrow, option 2 provides maximum space to the left of the fence for handling large sheets of plywood. If you often work with full sheets of plywood or other sheet goods, you might want to build the table saw into an extension table surround, as San Diego woodworker Pat Curci did in his small shop (see the photo). The surround offers support for large panels, as well as provides an ample work surface near the saw.