That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000.
In this video Dave Heller shares an introduction to wood veneering and wood inlay for furniture making. What is veneering and inlay? They are traditional methods used to embellish and beautify furniture. Veneering is the process of gluing thin slices of attractive (and often rare) wood onto core panels. Inlay involves insetting wood, precious stones, etc. into the wood. Here's a prime example of one of Dave's boxes that incorporates both techniques: Here is an example
I have found that drawing everything to scale on grid paper is most helpful. That is what I am doing in preparation for my new shop. I will, however need to share that space from time to time with my wife’s hobby (hatching and raising chickens). Just a few in the spring till they get big enough to go outside. I am planning on a 26″ x 40″ building with infloor hydronic heat. Others have mentioned that you can’t have too much light, and I intend to use the 200 watt cfl’s to accomplish this, along with task lighting at each machine. Walls and ceiling will be painted white to reflect as much of that light as I can. I want to use the same type of floor treatment that Marc has used in his new shop. Marc, is it really expensive to do that? Or if a guy has never done that would it be better to hire out that job? Lumber storage I have not decided yet. I am fortunate that I am able to fell trees on our farm and have them cut up so I can stack and dry them. We have white oak, red oak, maple, cherry and pine. Although drying/storage will be in another building will still have to tote my boards around some.
The standard option for a shop floor is a concrete slab. You’re probably not going to go to the trouble of creating a basement beneath your shop, although it is possible. The weight of most woodworking machines suggests that a concrete floor is the most solid and durable substrate available. It has the potential to be used as thermal mass to store heat from your heating system or from the sun, but it can be tiring and hard on your body to be standing on concrete all the time. You can add a vapour barrier, 2x4 sleepers and a wooden floor above the concrete to ease the tendency of the floor to strain your feet and back, or you can add anti-fatigue mats in key areas where you’ll be standing for longer periods.
I agree with all of these tips in a larger shop. In a smaller shop (mine is just under 400-square feet) most things are fairly close together anyway. One of my original principals for shop layout was … how is a machining process performed on a piece of wood? Is the wood stationary while it is machined … or does the wood move through the machine? If the wood is stationary, I have tried to have this set for one side wall of the shop. To be specific, I have four machines in one line with a continuous table to support long pieces that might need cutting from one or all of those machines. The machines in that line are (from left to right) the drill press, the powered miter saw, the square-chisel mortiser and the radial arm saw.
In each case, we shuffled the bench, jointer, table saw, and band saw across to the top of the stairs, and then tied a rope around each to act as a safety while sliding the machines down the strapping on the stairs. Yeah, the table saw hit the wall, and the promise of a good mud and paint job saved my bacon. The rope worked well, and we were able to get everything down the stairs nice and slowly without any major issues.
Short scraps of hardwood are too good to throw away but hard to store neatly. So I bought a 4-ft. tube form made for concrete footings, cut it in half (the cardboard-like material cuts easily) and set the tubes on end. I tack the tubes to a wall or a bench leg so they don’t fall over. With the wood scraps stored upright, it’s easy to find a piece just the right length. Tube forms are available in various diameters for $5 and up at home centers. — Bill Wells. Here’s another brilliant use for these concrete forms.
When cutting full sheets with my circular saw, I use plastic shelving units as sawhorses. The height is just right and by using three of them, I can make cuts in any direction and the plywood is fully supported. And because the shelving units are made of plastic, I can cut right into them without worrying that they’ll damage my saw blade. Plastic shelves are available for $20 at home centers. — John Tinger. Check out these tips for making long cuts with a circular saw.
With strength, sturdiness, and durability, maple is a common material for furniture for the bedroom and even china cabinets. Maple is moisture-resistant and frequently displays stand-out swirls in the wood grain, an aesthetically pleasing differentiator from other hardwoods. While most commonly a lighter color, maple also can take stains and paint well.
Once you’ve planned the basic layout of your workshop and have added all the tools and speciality appliances you need, take a last look at the overall design to make it aesthetically pleasing. Add overhead lighting for general illumination and task lighting over your work stations so you can see your project clearly. For maximum flexibility, you can mount clip-on work lights to nearby shelves and point them where you need them, knowing you’ll be able to move them about as required for different projects.
Spray gun: Not every woodworking job gets a film finish, but most of mine do. And of those, everyone will meet a spray gun. For a million reasons, including making finishing fast and fun, I recommend using a spray gun whenever possible. It will raise your game and make you n0t hate finishing. (Click here to read my thoughts on purchasing a spray gun).
This simple jig makes laying out circles a breeze. Drill a 1/8-in. hole through every inch mark on a ruler or yard-stick. To draw a circle, place a pin through the number “1” into the center of your board. Add 1 in. to the radius of the circle you wish to draw, and insert a pencil into this number. Using the pin as a pivot, rotate the pencil to mark the circle. — Edwin Constantino. How to Cut Curves in Wood
The dream of a dedicated home shop is a common one among woodworkers. Whether you currently borrow shop space, work in your driveway or side yard, or compete for a corner of your basement with Christmas decorations or your furnace, you may be ready to build your own space that will allow you the freedom of more room and time, and will also keep dust, fumes, and noise under control. Every design/build situation will be unique but there are a series of considerations that you will face in the design and construction phases of your project. Let’s walk through the process and discuss the questions that you will need to ask yourself and others as you approach this project.
My planer blasts shavings all over the shop floor. I decided to make my own dust chute from 4-in. PVC sewer pipe (which has thinner walls than regular Schedule 40 pipe) and a couple caps. I cut a slit in the pipe and used a heat gun to soften the plastic. That allowed me to open the slit. (Heating PVC releases fumes; ventilation is critical.) I then drilled holes in the flap and screwed it to the planer housing. Finally, I cut a 2-1/2- in. hole in one of the end caps to accept my shop vacuum hose. Works great! — Luis Arce. Here’s what else you can do with PVC pipe.
Set the table saw fence so the blade is centered on the seam, then push the whole thing through the saw. If the board edges are quite bowed or curvy, you may need a second pass. If so, unscrew the cleats, reclamp the boards across the middle center, then screw on the cleats again. The screws ding up the ends of the boards a little, so cut the boards you’re jointing a bit long, then trim 1/2 in. from each end to remove the screw holes.
WoodAndShop.com recommends products, with links to online stores, some of which are part of affiliate programs. If users make purchases in those stores (e.g. ebay.com and Amazon.com) those affiliate links lead to referral compensation to us. These payments are very helpful to us, and add no additional fees to our users, so we are grateful for anyone who uses the affiliate links. We run our website based on principles of integrity, and don’t recommend any product that we wouldn’t use ourselves. Any product claim about a service or product should be verified with the manufacturer.
I saw in the March 2019 Vol36,No.1 Iss 259. I have 2 Christian people very close to me that could likely be getting married soon . When I saw the unity cross on page one this would be the perfect gift from a parent. I would like to make it but need the plans. I do not need 3,000 or 60,000 plans I just wish to purchase the plans for the unity cross. I am a beginner so I need detail plans. Please send me information on ordering just the unity cross plans and where to purchase giant Sequoia and white oak woods. Thank you in advance for your help. I need the plans and information before April.
The progenitors of Chinese woodworking are considered to be Lu Ban (魯班) and his wife Lady Yun, from the Spring and Autumn period (771 to 476 BC). Lu Ban is said to have introduced the plane, chalk-line, and other tools to China. His teachings were supposedly left behind in the book Lu Ban Jing (魯班經, "Manuscript of Lu Ban"). Despite this, it is believed that the text was written some 1500 years after his death. This book is filled largely with descriptions of dimensions for use in building various items such as flower pots, tables, altars, etc., and also contains extensive instructions concerning Feng Shui. It mentions almost nothing of the intricate glue-less and nail-less joinery for which Chinese furniture was so famous.
These are all good tips, and apply to pretty much every shop. Like all things woodworking they need to be tweaked so that it’s right for the individual. For instance, I have a basement shop that’s not tiny but it is still space constrained, so worrying about the optimal layout for my ts/jointer/planer is a little off the mark since I don’t have to walk very far; instead, I want to be sure that related tools can be used *at the same time*. Having to move the planer out of the away so that I can use my TS is crazy if it can be avoided. However, interference between my drill press and my planer is less of an issue because they usually don’t get used at the same phase of a project.
Some of the most important decisions in laying out a shop involve the placement of basic machines, such as the table saw and jointer. Deciding where to put them depends in part on the scale of woodworking you do, which determines the clearance area around these machines if you need to handle long stock or large sheet goods. You’ll also want to consider work flow to avoid an excess amount of running around the shop to accomplish tasks, as well as how to power your machines without turning your shop into a snakepit of extension cords.