The layout of a workshop will be based, in part, on how it will be used — whether for carpentry, fine woodworking, metalwork or other activities. Regardless of category, however, it's important to keep in mind the principles of efficiency and organization. A layout that's clearly thought out in terms of functionality will make all the difference in creating a workspace that offers a pleasant surrounding as well as a space that's conducive to work.
Lacking a jointer? Use reader Court Kites’ awesome tip to create perfectly matched glue joints on wavy or bowed board edges. Lay the boards on a flat surface, then clamp them across the middle with a bar clamp. Lay two 8-in. long by 1-3/4 in. wide scrap boards across each end and screw them in with four 1-1/4 in. long screws, two per board. Keep the screws well away from your future cutting line!
Gone are the days when you could apply for a building permit based on a sketch on the back of a cigarette pack­age. In provinces like Ontario, design work must be undertaken by an insured designer registered under the provin­cial building code or by the owner of the property. You can do the drawings as the owner if you can demonstrate effec­tively through your drawings that your structure will comply with the techni­cal requirements of the building code in a clear and concise way. You will be required to submit detailed drawings, including the following:
Use whatever image hosting service you like and post the link to /r/woodworking. The key here is it needs to be apparent that you've built the entry, and you follow the photo requirements listed in the contest rules. Submissions of finished photos only will not be accepted for entry. <-- I can't emphasize this enough, you absolutely need more than 2-3 photos for a valid submission. I will no longer accept entries that have albums that go from rough stock to 90% complete in one jump.
Next come two options for the table saw’s trusty sidekick, the jointer, as well as for the thickness planer. Because it’s usual to work between all three tools when dressing lumber, the first option, shown in the illustration, locates the jointer nearest the saw to the right of its extension table with the planer nearby. As with the table saw, it always makes sense to align these tools with the shop’s long axis.
With two varieties, red and white, oak is known to be easy to work with and relatively strong. However, furniture makers often opt for white oak over red oak for its attractive figure and moisture-resistance.[12] Depending on the kind needed, oak can probably be found at a local home center or a lumberyard for a bit pricier than other hardwoods.[12][13]
Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.
A great freestanding beverage cooler should come equipped with a thermostat that lets you control the temperature to your liking — the colder the better for carbonated drinks, which tend to taste best when served at a frosty 34 degrees. If you plan to store adult beverages in your cooler, look for a model with a lock to keep your drinks away from children and teens. You’ll also want a model that allows you to reverse the way the door swings when you set it up, as this will provide flexibility in your workshop layout to help maximize your space.
For all of my planning, I must admit there simply was no room in my shop for some tools. I struggled to find a place for my wide jointer and eventually decided against shoehorning it in, instead making a fixture for my router table that joints edges quite well. My scrollsaw, the bulk of my wood supply, and some storage cabinets didn’t make the cut either. These remain in a nearby room.
If you live where summers get hot and humid, you may need more than a fan to keep cool in your workshop. Fortunately, air conditioners will both dehumidify and cool your space — and you don’t need a traditional window to get the job done. Instead of a residential window unit, consider a freestanding portable air conditioner that you can use as needed on hot days.
When it comes to woodworking for beginners, I think it’s important to just learn how to use a few of the most essential woodworking tools for beginners. There are so many awesome tools available on the market today, it can be quite overwhelming as well as expensive to try to buy them all and know how to use them. Once you learn the basics of the most essential tools you will be able to start building in no time and feel comfortable learning any other new tools in the future.
This is a fundamental question. A good place to start is with a survey of your property. Most municipalities have a maximum percentage of your lot that you can build on and standard setbacks from your property lines that you will need to adhere to without needing to request special permission to build. On a photocopy of your survey you can draw in what your local setbacks are in order to define the location within which you will be permitted to build. In a best-case scenario, you will have the space to build without compromising too much on space or location; otherwise, you may need to request a minor variance, which would allow you to circumvent an obsta­cle such as a setback.
I’m helping my son (who is significantly disabled) get started with a business idea that he had — one that I’d think was brilliant even if I weren’t his Mom — brilliant enough that I’ve “retired” from my law practice and moved us from MO to GA. Having lost 99.9% of ALL of my tools in the move (even the big ticket items, nearly 30 years collection — stolen by the mover!) I am now re-investing in tools, limiting my purchases to what we must have rather than all the fun stuff I used to have. . . .(So sad).
Minor variances are applications to your municipality to suspend a particular by-law to allow your project to proceed, based on common sense or precedents set by other buildings in your area. If your municipal committee of adjustment denies permission because a neighbour voices concern over the development, you would have to appeal the decision to the municipal board of your particular province. In that case, you may be better off looking for another piece of property with an existing structure that you could renovate, more relaxed zoning regula­tions, a larger lot, or more congenial neighbours. 
If your table saw is near a wall and your shop is fairly narrow, positioning the jointer and planer against the opposite wall is reasonable, as shown in option 2 in the illustration. If the shop isn’t long enough to accommodate long workpieces, try to put these machines near an operable doorway, as shown in the illustration and in the photo of Doug Warren’s shop.
×