Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.
“I do a lot of finish-sanding freehand, without a sandpaper block, so I can smooth edges and get into nooks and crannies. But the finer grits are usually bonded to thinner paper and, at least for me, the paper is too thin and ends up tearing long before the grit wears out. So I apply duct tape to the back of the sandpaper. The sandpaper is still flexible enough to sand a tight radius and it’s far more durable. You can use this super-strong sandpaper like a shoeshine rag.” — Chuck Merchant
Even if you buy your lumber already planed, you will still encounter many circumstances that require the use of a planer. For example, you might want to build a simple and delicate jewelry box out of small scrap pieces lying around the shop, and you will end up making a small and clunky jewelry box because all of your lumber is 3/4″ thick, and that’s how it is going to stay. That is just the first example. Think about all of the other times that you will pick up a piece of lumber in the shop and it will be the wrong thickness, either just slightly wrong or in an entirely different size category. A planer is a real problem solver and can fix all of that.
Use whatever image hosting service you like and post the link to /r/woodworking. The key here is it needs to be apparent that you've built the entry, and you follow the photo requirements listed in the contest rules. Submissions of finished photos only will not be accepted for entry. <-- I can't emphasize this enough, you absolutely need more than 2-3 photos for a valid submission. I will no longer accept entries that have albums that go from rough stock to 90% complete in one jump.
In this video Dave Heller shares a detailed tutorial on making fancy London-style dovetails with a mitered corner. The London-style dovetail originated in, well, London where cabinetmakers sought to show off their joinery skills by cutting the finest pins possible. Adding a miter to dovetails is very useful for wrapping a dovetailed skirt around a tool chest, or for adding embellishment to a cupboard's carcass. In the very near future I'll be releasing the last video,
Once the workshop location is determined, it's time to begin planning how to lay it out. First, acknowledge the need to formulate a plan that's realistic in terms of the space allotted. The size of the structure or workspace will place some constraints on how much can be done. Taking into account size limitations, begin fashioning a plan that keeps efficiency in mind.
With two varieties, red and white, oak is known to be easy to work with and relatively strong. However, furniture makers often opt for white oak over red oak for its attractive figure and moisture-resistance. Depending on the kind needed, oak can probably be found at a local home center or a lumberyard for a bit pricier than other hardwoods.
With strength, sturdiness, and durability, maple is a common material for furniture for the bedroom and even china cabinets. Maple is moisture-resistant and frequently displays stand-out swirls in the wood grain, an aesthetically pleasing differentiator from other hardwoods. While most commonly a lighter color, maple also can take stains and paint well.
There are many factors to consider when deciding what type of wood to use for a project. One of the most important is the workability of the wood: the way in which it responds when worked by hand or tools, the quality of the grain, and how it responds to adhesives and finishes. When the workability of wood is high, it offers a lower resistance when cutting and has a diminished blunting effect on tools. Highly workable wood is easier to manipulate into desired forms. If the wood grain is straight and even, it will be much easier to create strong and durable glued joints. Additionally, it will help protect the wood from splitting when nailed or screwed. Coarse grains require a lengthy process of filing and rubbing down the grain to produce a smooth result.
A shop geared toward woodworking would have lumber storage located at one corner of the triangle. Storage space for wood — both long pieces and flat plywood pieces — should be adequate. Raised storage, such as racks or shelves mounted on the wall, must be sturdy. Wood storage should also be in close proximity to the stationary tools or machines (table saw, jointer, power planer, etc.) to avoid frequently carrying heavy wood across the span of the workspace. Wood storage should be handy and near the area where the heavy woodworking tasks will take place. Keep in mind that a considerable amount of space will be needed around stationary tools such as a table saws and jointers for manipulating large pieces of raw lumber.
If your table saw is near a wall and your shop is fairly narrow, positioning the jointer and planer against the opposite wall is reasonable, as shown in option 2 in the illustration. If the shop isn’t long enough to accommodate long workpieces, try to put these machines near an operable doorway, as shown in the illustration and in the photo of Doug Warren’s shop.