Unless you’re a big fan of frequent shop remodeling, planning the layout of your workshop early in its development will save you a lot of time and trouble and also can keep you from spending years in an uncomfortable, poorly organized space. And if you already work in a shop that’s as organized as a trailer park after a tornado, careful planning and a little remodeling is likely to help you make a quantum leap.
You sure make “keeping up with the Spagnuolo’s” tough. :) The cart fits my space pretty well. I am somewhat limited so utilizing the space under the lumber rack works well for me. I have the stand alone scrap storage bin also but the extra scrap storage on the cart is a bonus. I always seem to have srcap lumber running out of my ears. I have a hard time throwing away even a small piece of walnut or other nice (expensive) wood.
Rockler Buffalo is proudly hosting the CNC Users Group! The club consists of CNC owners, users and prospective buyers. Every meeting consists of a ‘Show-n-Tell’ portion, demonstration and then a group discussion. We’d be happy to have you join us and we’ll be looking forward to seeing you at the store! Don’t miss out on this one of kind experience.
There is significant evidence of advanced woodworking in ancient Egypt. Woodworking is depicted in many extant ancient Egyptian drawings, and a considerable amount of ancient Egyptian furniture (such as stools, chairs, tables, beds, chests) has been preserved. Tombs represent a large collection of these artefacts and the inner coffins found in the tombs were also made of wood. The metal used by the Egyptians for woodworking tools was originally copper and eventually, after 2000 BC bronze as ironworking was unknown until much later.
Alternately, a detached shop can often be located closer to your property line and offers you a bit more freedom in terms of the type of foundation you can use. It may give you a sense of welcome separation from your home and open up yard space or allow a deck on the back of your house that would otherwise be lost behind your shop. In an urban setting, if you would like to have a wood stove in your shop you may find it more challenging to find an insurance carrier that allows one in an outbuilding. Also, outbuildings can be subject to more stringent height regulations than additions.
I mix a lot of epoxy in small batches, but I’ve seldom had the right size container on hand. I solved this problem by drilling 1-1/2-in. holes in 2×4 scraps with a Forstner bit. The resulting shallow “cups” allow easy mixing without the risk of spilling. When the holes are used up, I just make a new mixing board. — Bill Wells. Save your takeout utensils to use in the shop!
This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off serious cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bottom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thickness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop without excessive grunting, so that made it very simple to install. The planer has a significant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.
In this video Dave Heller shares a detailed tutorial on making fancy London-style dovetails with a mitered corner. The London-style dovetail originated in, well, London where cabinetmakers sought to show off their joinery skills by cutting the finest pins possible. Adding a miter to dovetails is very useful for wrapping a dovetailed skirt around a tool chest, or for adding embellishment to a cupboard's carcass. In the very near future I'll be releasing the last video,
As the comic George Carlin might say, a shop is mostly just “a place to put your stuff.” The physical aspect of a shop is indeed simply a space of some kind — a garage, a barn, a teepee — that keeps the rain, rust, and robbers away and houses a collection of implements needed to saw, plane, slice, sand, and pound raw wood into useful objects. But just like the difference between a house and a home, what transforms a building full of tools into a comfortable workshop goes beyond the mere physical aspect.