In addition to keeping your workshop comfortable with climate control add-ons, don’t forget to keep your body in optimal condition as you work. A water cooler tucked away in the corner of your workshop will provide a big quality of life boost and allow you to keep at your projects without having to run to the kitchen for a glass of water every time you feel thirsty.
Hardwoods are separated into two categories, temperate and tropical hardwoods, depending on their origin. Temperate hardwoods are found in the regions between the tropics and poles, and are of particular interest to wood workers for their cost-effective aesthetic appeal and sustainable sources. Tropical hardwoods are found within the equatorial belt, including Africa, Asia, and South America. Hardwoods flaunt a higher density, around 65lb/cu ft as a result of slower growing rates and is more stable when drying. As a result of its high density, hardwoods are typically heavier than softwoods but can also be more brittle. While there are an abundant number of hardwood species, only 200 are common enough and pliable enough to be used for woodworking. Hardwoods have a wide variety of properties, making it easy to find a hardwood to suit nearly any purpose, but they are especially suitable for outdoor use due to their strength and resilience to rot and decay. The coloring of hardwoods ranges from light to very dark, making it especially versatile for aesthetic purposes. However, because hardwoods are more closely grained, they are typically harder to work than softwoods. They are also harder to acquire in the United States and, as a result, are more expensive.
Finding affordable lumber has always been a mainstay for woodworkers, and when you tie our dwindling natural resources into the conversation the time is right to look at milling your own lumber. This seven-part weekly video series takes you through how to find lumber, how to operate a sawmill, details on types of sawing methods, stickering and drying and ultimately advice on using a mill as part of a business. Learn what you need to know to understand Milling Your Own Lumber.
Tape measure: I know this isn’t a power tool, but it is the one tool that you should always have with you. It is a pet peeve of mine – if you are planning on building something, or you are actually building it, have a tape measure with you. If you are in the shop, on the job site, or even at Home Depot make sure you have a tape measure with you or at least one very handy (Home Depot probably isn’t the best example, since they have them widely available, but you get the point). Without a tape measure, not much beyond rough work can get done.
How do you divide 11-3/8-in. (or any other mathematically difficult number) into equal parts without dividing fractions? Simple. Angle your tape across the workpiece until it reads an easily-divisible dimension and make your marks with the tape angled. For example, say you want to divide an 11-3/8-in. board into three equal parts. Angle the tape until it reads 12-in., and then make marks at “4” and “8”. Plus: More measuring tips and tricks.
Electricity. It’s a rare workshop today that doesn’t need electricity; most need multiple receptacles of high amperage (20 amperes or more). Are there plugs available or will you need to add new lines and circuits? If you need to add wiring, when laying it out keep in mind that there’s no such thing as too many outlets in a workshop. The fewer (as in, ideally, zero) extension cords the better; they’re safety hazards. A good minimum is to have receptacles set at no more than six-foot intervals around the perimeter of the room, and, if possible, flush-mounted floor plugs in the central area.
Spray gun: Not every woodworking job gets a film finish, but most of mine do. And of those, everyone will meet a spray gun. For a million reasons, including making finishing fast and fun, I recommend using a spray gun whenever possible. It will raise your game and make you n0t hate finishing. (Click here to read my thoughts on purchasing a spray gun).
Hi Liz. I am sorry you were having trouble unsubscribing to the newsletter. Your information has been updated. Your email address has been removed from our Woodworkers Guild of America E-Newsletter mailing list. Please allow up to 5 business days for your request to be completed. If you have any questions, please contact our customer service team at 1-855-253-0822.
Welcome to The Woodwork Shop, Inc. We are glad you are here! We are a locally owned and operated woodworking shop, serving the greater Memphis Metropolitan area. Located just off of I-40 in Bartlett we are easy to get to from just about anywhere. We have over 5000 square feet totally devoted to woodworking and woodworking equipment, and a very knowledgeable staff. We have FREE Saturday Seminars every Saturday at 10:30am, and also offer weekly classes on Monday nights. Come on in, or give us a call if you have questions at (901) 755-7355 or email us at firstname.lastname@example.org. We can’t wait to see you!
To plan my shop, I used a modeling program on my computer, but you can use the drawings I created to plan an efficient shop on paper. Download and print the PDF below and arrange them on graph paper to create a plan view of your shop. Take the time to work out the most efficient placement of benches, cabinets, and machines, taking into account infeed and outfeed zones as well as ducting for dust collection.
Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.
This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off serious cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bottom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thickness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop without excessive grunting, so that made it very simple to install. The planer has a significant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.
My shop ended up being 23 x 19 feet, for a total of 437 square feet. I put my wood rack in the basement, but outside the walled in shop area. To keep the dust in the shop, a three part strategy was employed. I have a dust collection system, an air filtration system and a shop vacuum for cleaning dust out of machinery. I put up new walls, installed new electrical service, lighting, and two access doors for ease of materials movement. The shop includes two windows so that I can enjoy natural light, and not feel like I am squirreled away in the basement.
Usually ducting is well covered and one of the first things considered, however, most people initially neglect clean up when designing shops. With growth, I have a very cluttered shop that makes pulling shop vacs around frustrating especially if you’re at the wrong end of a 5m flexible hose without having to struggle with the vac (the practice of in no doubt exacerbated by those ridiculous vacuuming ads on TV). As my setup is retro fitted, it may not be pretty as it is ducted overhead, but it is productive. I have a centralised heavy duty ‘shop vac’ (rigged with a Dust Deputy) and 50mm stormwater piping radiating to selective parts (corners) of the workshop. I use 50mm water diverters to act as blast-gates to control the flow of air (I have a bank of them running down one full side of the workshop spaced about 5m apart). When I need to clean a part of the shop I plug the vac into the appropriate overhead vent, organise the diverters and attach a 5m flexible hose to the working end. I have the vac on a remote (one of those that control power points – all my dust extraction is controlled by these – after modifying any proprietary mag switches) and I can vacuum any part of my workshop without having to go and manually switch the vac on. I have bought some cheap off market flexible hoses and spread them at the extremities of the workshop. Each outlet will accept the hose. Hint – I bought a fairly low end 3D printer ($800 (Aust)) and I can print any sized coupling to accommodate all those non-standard ‘shop vac’ hoses/fittings to accept my proprietary shop vac accessories. Duct tape is now reserved for the few threaded non-standard couplings.
I really appreciate the article. I am always looking for a way to improve my shop and its layout. I currently have a 34′ x 28′ garage which I park two vehicles and still have some room for a table saw, large bench and various smaller benches and cabinets. All of my large power tools are on casters so I can roll them out when I move the cars outside. Right now I am considering keeping my little truck outside permanently and set the shop up more in a fixed layout. This would make working in the shop more enjoyable and much easier to do more complex projects that I currently take on. Maybe this spring. Thanks for the advice.
To make sure you account for any existing obstructions, it’s a good idea to make a measured drawing of your workshop area on graph paper, noting existing furniture, built-ins and large items on the plan as you go. For example, a common one-car garage workshop layout has built-in tool cabinets and shelves around the perimeter where they won’t impede parking, but you may also have to get clever about folding work tables and saw horses that you can set up as needed in the middle of the garage when you’re working on a project (and cars are parked outside).