#### KHIEM NGUYEN (Age 28, Austin, TX): Inspired by midcentury modern and Japanese design, Nguyen is a true craftsman. His passion for crafting began with photography and led to him becoming an open major in art school so he could "get (his) hands into everything." After college, Nguyen and his fiancée moved to Austin, where they began A & K Woodworking & Design, specializing in furniture and wood crafts.

You sure make “keeping up with the Spagnuolo’s” tough. :) The cart fits my space pretty well. I am somewhat limited so utilizing the space under the lumber rack works well for me. I have the stand alone scrap storage bin also but the extra scrap storage on the cart is a bonus. I always seem to have srcap lumber running out of my ears. I have a hard time throwing away even a small piece of walnut or other nice (expensive) wood.
How do you divide 11-3/8-in. (or any other mathematically difficult number) into equal parts without dividing fractions? Simple. Angle your tape across the workpiece until it reads an easily-divisible dimension and make your marks with the tape angled. For example, say you want to divide an 11-3/8-in. board into three equal parts. Angle the tape until it reads 12-in., and then make marks at “4” and “8”. Plus: More measuring tips and tricks.
The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.

In this video Dave Heller shares an introduction to wood veneering and wood inlay for furniture making. What is veneering and inlay? They are traditional methods used to embellish and beautify furniture. Veneering is the process of gluing thin slices of attractive (and often rare) wood onto core panels. Inlay involves insetting wood, precious stones, etc. into the wood. Here's a prime example of one of Dave's boxes that incorporates both techniques: Here is an example
The thickness planer—A thickness planer will significantly expand the creativity and craftsmanship of your work by allowing you to buy roughsawn stock and use wood of any thickness in your designs. Nowadays, a new planer often represents a better value than a used model. In recent years, DeWalt and Ridgid have introduced portable planers with chip-ejection fans, which work as a built-in dust collector. Dust collection is important for all tools, but essential for thickness planers. This feature can help delay the expense of a dust collector and thus reduce the overall cost of a planer. Speaking of dust collection, I should mention that I don’t use a dedicated dust collector in my shop. I use a shop vac with a small hose for my sanders and a larger-diameter hose for the tablesaw and router table, and I depend on the built-in chipejection fan for my thickness planer.
Clamping up four mitered corners is tricky. You can buy specialty clamps for this, but I make my own. Here’s how to do it. Start with a long 1×4, as it’s easier (and safer) to clamp for making the angled cuts than a short piece. Mark out the blocks, and then drill a 1-in. diameter hole in the center of each one. The hole prevents the blocks from getting glued to your project. Cut 45-degree angles tangent to the hole, and then cut the blocks free from the long board. We’ll walk you through how to make one for your home shop.
Often times at first glance a board looks straight and the fact that it is actually bowed or has some warping isn’t always obvious. So the trick to knowing for sure, is to hold the board up towards your face, with the other end on the ground, and look at it at a downward angle (as shown in the below photo). This method will allow you to see if it is bowing at all.
This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com.
One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at \$50/sheet.

Radial-arm saws, sliding compound miter saws, and powered miter boxes (chop boxes) used for crosscutting long boards are best located against the longest wall of the shop, as shown in the first option in the illustration. If the saw is to become a stationary machine, it’s typical to mount or build it into a long, narrow support table fitted with a fence.