Finally, properly preparing your wood surface is super important. It will make a huge difference when it comes times to stain, paint, or finish your wood. There are a lot of tips for wood surface preparation, but sanding the wood is one of the most important steps. And I find it really helpful to do the bulk of my sanding before I start ripping (cutting) and building with my wood since it’s still in whole pieces. You can check out my simple tips for how to sand wood in my how to stain wood tutorial, which is also good to reference if you need to learn how to stain too!
When cutting full sheets with my circular saw, I use plastic shelving units as sawhorses. The height is just right and by using three of them, I can make cuts in any direction and the plywood is fully supported. And because the shelving units are made of plastic, I can cut right into them without worrying that they’ll damage my saw blade. Plastic shelves are available for $20 at home centers. — John Tinger. Check out these tips for making long cuts with a circular saw.
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
Softwood is most commonly found in the regions of the world with lower temperatures and is typically less durable, lighter in weight, and more vulnerable to pests and fungal attacks in comparison to hardwoods. They typically have a paler color and a more open grain than hardwoods, which contributes to the tendency of felled softwood to shrink and swell as it dries. Softwoods usually have a lower density, around 25-37lb/cu ft, which can compromise its strength. Density, however, does vary within both softwoods and hardwoods depending on the wood's geographical origin and growth rate. However, the lower density of softwoods also allows it to have a greater strength with lighter weight. In the United States, softwoods are typically cheaper and more readily available and accessible. Most softwoods are suitable for general construction, especially framing, trim, and finish work, and carcassing.
The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.
This self-clamping table saw fence takes only seconds to put on and lets you crank the blade into the fence to create both angled cuts along board edges and extremely thin rip or rabbet cuts. With a hand- or jigsaw, cut pieces from a 1×4, making the inside width of the “L” a hair under the thickness of your saw’s fence. Drill 5/16-in. holes in the L-blocks and plywood fence and join them with two 1/4-in. x 3-in. countersunk machine screws, washers and Wing-Nuts. As always, use extra caution when you’re sawing without a blade guard. Our thanks for this new sawing angle to professional furniture maker George Vondriska. Check out these 16 genius tool hacks you need to know!
Electricity. It’s a rare workshop today that doesn’t need electricity; most need multiple receptacles of high amperage (20 amperes or more). Are there plugs available or will you need to add new lines and circuits? If you need to add wiring, when laying it out keep in mind that there’s no such thing as too many outlets in a workshop. The fewer (as in, ideally, zero) extension cords the better; they’re safety hazards. A good minimum is to have receptacles set at no more than six-foot intervals around the perimeter of the room, and, if possible, flush-mounted floor plugs in the central area.
If you have to pick up long lengths of wood from the lumberyard, throw a spring clamp in the back of your vehicle. Use the clamp to attach the warning flag to the end of the protruding lumber. The clamp’s easy to slip on and off, and you won’t have to fuss around with staples, nails or string. — Steve Parker. Plus: Learn more about how to transport large items in your truck.
With two varieties, red and white, oak is known to be easy to work with and relatively strong. However, furniture makers often opt for white oak over red oak for its attractive figure and moisture-resistance. Depending on the kind needed, oak can probably be found at a local home center or a lumberyard for a bit pricier than other hardwoods.
Ultimately, your workshop should be a place that inspires you to be creative and to do your best work. When you take the time to plan the space for maximum efficiency and comfort, you’ll love spending time there — and that means you’ll get more done, whether it’s fixing up a car or building a new piece of furniture. No matter how you use your workshop, you should enjoy the time you get to work with your hands and make something brand new. So what are you waiting for? Get started designing your perfect workshop today.
Tabletop versus Freestanding Tools. When purchasing some power tools (the list includes the jointer, shaper, sander, and even some models of table and band saw), you may decide to opt for benchtop models. A single bench can then serve, alternately, a range of purposes. Make- ready time is increased significantly, of course, as not only the blades, fences, miter gauges, and the rest must be set but the machine itself has to be positioned and powered. But for the small shop, the infrequently used tool may be quite easily stowed on a shelf out of the way, opening up more space for other tasks.
Particleboard is a manufactured wood product composed of sawdust, wood chips or wood shavings mixed with a resin. This concoction is layered, compressed, subjected to heat and cut to shape, resulting in a sheet material that can be used for a variety of things. It’s often used as shelving or as an underlayment for carpet. Plastic laminate may be applied to both sides to create a product that can be used to create everything from furniture to cabinets to wall paneling. Head into IKEA and you’ll find acres of particleboard.
Much like the assembly table, nearly every project in my shop makes extensive use of the table saw. And like it or not, my outfeed table becomes a second storage area for project parts and cut-offs. So I like to have mine located in the middle of the shop for the same reasons as the assembly table. Additionally, it’s nice to have ample space around the tablesaw for those larger workpieces. Unless it’s absolutely necessary, I’m not a fan of storing the table saw against a wall.
The table saw also works amazingly well as a table. Mine is big enough to not only hold stuff, but serve as an assembly table when necessary. The table of the table saw is set apart from other tables because it is commonly the only one open and available in the shop. I try to keep it clear enough to actually use, which means that at least part of the top is usually available and ready to be used as a table or maybe even a saw.
A good portable air conditioner will also remove excess water from the air, which is critical for keeping your stockpile of wood in good shape. Lumber should be stored in dry conditions so it doesn’t warp, so look for efficiency features that allow you to run the unit overnight in the summer as needed —without worrying about blowing up your electricity bills. Other good features to consider include a thermostat and variable settings that allow you to set your workshop temperature to the perfect level for your comfort.
My contention has always been that you can build a serviceable shop in your home, develop your hand skills, and make fine furniture. In the past year, I had an opportunity to build a shop from the ground up after moving to a new home. I found a house with an unfinished basement, and set to work. In this article, I will discuss everything from layout, to electrical, to equipment selection. I intend to name names with respect to equipment, so that readers will know what I chose. Everyone’s budget will be different, but I think almost everyone will be able to treat this as a starting point, and adjust accordingly, depending on their own budget.
Some types of wood filler can be hard to get off your hands after they dry, especially if you use your fingers to push it into small cracks and holes. When that happens, I reach for fine grit sandpaper and sand it off my fingers. It’s great for removing dried-on polyurethane glue and canned foam from your hands, too. — Chris James. We’ve got great solutions for removing super glue, too.
First, let’s take a look at four placement options for the table saw, the machine that is at the heart of most woodshops. The first option (see the illustration) places it in the center of the shop, which lends maximum space and flexibility for ripping and panel sawing, as well as crosscutting long boards. The main requirement here is a shop that’s at least long and wide enough to allow room for the workpiece, both on the infeed and outfeed sides.