It has made me really think about doing things in an order which optimizes the switching around of machinery. One thing I did do which has really helped and that I would add to your list is SOUND PROOFING! Didn’t mean to yell there.. lol. Sound proofing has has allowed me to keep the workshop operations from bothering the rest of the family when I am in my man-room.
A good portable air conditioner will also remove excess water from the air, which is critical for keeping your stockpile of wood in good shape. Lumber should be stored in dry conditions so it doesn’t warp, so look for efficiency features that allow you to run the unit overnight in the summer as needed —without worrying about blowing up your electricity bills. Other good features to consider include a thermostat and variable settings that allow you to set your workshop temperature to the perfect level for your comfort.

Among early finds of wooden tools are the worked sticks from Kalambo Falls, Clacton-on-Sea and Lehringen. The spears from Schöningen (Germany) provide some of the first examples of wooden hunting gear. Flint tools were used for carving. Since Neolithic times, carved wooden vessels are known, for example, from the Linear Pottery culture wells at Kückhofen and Eythra.

Rockler Buffalo is proudly hosting the CNC Users Group! The club consists of CNC owners, users and prospective buyers. Every meeting consists of a ‘Show-n-Tell’ portion, demonstration and then a group discussion. We’d be happy to have you join us and we’ll be looking forward to seeing you at the store! Don’t miss out on this one of kind experience.


Click the image at right, and start building the ideal workflow at the bottom where you see the first red arrow. This arrow crosses through one roll-up door of a typical two-car garage. Note that if the right-hand window were not present, you could place lumber storage closer to the entrance, which would also allow for easier passage onto the jointer. Work flows from the jointer to the planer and the table saw, then ideally onto an outfeed table near position #2 in the diagram. From #2, proceed left to the assembly area (pictured below).


Jointer: I use my jointer a lot. When preparing rough lumber it sees as much action as the planer. As a matter of fact, almost every piece of lumber in my shop gets surfaced on the wide face to straighten things out before it even heads to the planer. Without the jointer, my life would just be a crooked, twisty mess of painful attempts to make things seem straight.
If a poured cement floor prohibits the installation of plug receptacles flush to the floor and you elect to surface-mount a plug, protect the exposed feed wire. A piece of one-by-four stock with a groove cut in its underside and its top edges chamfered, will pose little more tripping risk than a threshold. However, paint its protective covering a bright color to remind you and any other visitors to your shop of its presence.
See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products

Some types of wood filler can be hard to get off your hands after they dry, especially if you use your fingers to push it into small cracks and holes. When that happens, I reach for fine grit sandpaper and sand it off my fingers. It’s great for removing dried-on polyurethane glue and canned foam from your hands, too. — Chris James. We’ve got great solutions for removing super glue, too.
If you choose to hire a draftsperson or architect, they may charge you based on the square footage of the area you are proposing, by an hourly rate for their time or as a percent­age of the cost of the structure. Costs of building permits will be a percentage of the estimated cost of the structure you are proposing (e.g., $15 permit fee per $1000 or 1.5 percent), or a cost-per-square foot depending on your municipality (e.g., $1.20 per square foot). Design work and permits will both dif­fer depending on the part of the country in which you will be building, so ask the questions as you move ahead. One of the costs that is often overlooked in planning is the increase in annual property tax you will pay once your improved property has been reassessed.

My shop ended up being 23 x 19 feet, for a total of 437 square feet. I put my wood rack in the basement, but out­side the walled in shop area. To keep the dust in the shop, a three part strategy was employed. I have a dust collection system, an air filtration system and a shop vacuum for cleaning dust out of machinery. I put up new walls, installed new electrical service, lighting, and two access doors for ease of materials move­ment. The shop includes two windows so that I can enjoy natural light, and not feel like I am squirreled away in the basement.


Although refrigerators long ago rendered them obsolete, antique oak ice boxes remain popular with collectors, even though they’re expensive and hard to find. This do-it-yourself version is neither: it’s both inexpensive and easy to build. An authentic reproduction of an original, the project is especially popular when used as a bar, but it has many

The layout of a workshop will be based, in part, on how it will be used — whether for carpentry, fine woodworking, metalwork or other activities. Regardless of category, however, it's important to keep in mind the principles of efficiency and organization. A layout that's clearly thought out in terms of functionality will make all the difference in creating a workspace that offers a pleasant surrounding as well as a space that's conducive to work.


A clean well-organized environment is key to staying A clean well-organized environment is key to staying happy. The same goes for your desk. Keep the clutter at bay and organize all of your small essentials with the Dickies Work Gear 57050 Mug Organizer. Designed to fit over most mugs this clever caddy features 8 outer pockets and 6 ...  More + Product Details Close
As the comic George Carlin might say, a shop is mostly just “a place to put your stuff.” The physical aspect of a shop is indeed simply a space of some kind — a garage, a barn, a teepee — that keeps the rain, rust, and robbers away and houses a collection of implements needed to saw, plane, slice, sand, and pound raw wood into useful objects. But just like the difference between a house and a home, what transforms a building full of tools into a comfortable workshop goes beyond the mere physical aspect.
×