Position #3 is where you will likely spend most of your time in the shop. The diagonally placed workbench is the heart of this plan. The wall-mounted workspace that surrounds the bench forms an ideal “work triangle” within which each of your most commonly needed tools is only one or two steps away. The band saw can be placed outside of the work triangle because it is used slightly less frequently and often needs a little more space around it for your lumber to move.
This is a fundamental question. A good place to start is with a survey of your property. Most municipalities have a maximum percentage of your lot that you can build on and standard setbacks from your property lines that you will need to adhere to without needing to request special permission to build. On a photocopy of your survey you can draw in what your local setbacks are in order to define the location within which you will be permitted to build. In a best-case scenario, you will have the space to build without compromising too much on space or location; otherwise, you may need to request a minor variance, which would allow you to circumvent an obsta­cle such as a setback.
The rubber cushion on my old palm sander was wearing thin around the edges. Because of its age, I couldn’t find a replacement pad. As I was drinking my beverage with a foam can cover around it, I realized I could cut the foam to fit the sander and glue it on. I peeled off the old pad, cleaned the metal base and attached the foam with contact cement. Works for clamp-on as well as stick-on sanding squares! You can find can covers at discount and convenience stores. — Allen J. Muldoon
When it comes to woodworking for beginners, I think it’s important to just learn how to use a few of the most essential woodworking tools for beginners. There are so many awesome tools available on the market today, it can be quite overwhelming as well as expensive to try to buy them all and know how to use them. Once you learn the basics of the most essential tools you will be able to start building in no time and feel comfortable learning any other new tools in the future.
Electricity. It’s a rare workshop today that doesn’t need electricity; most need multiple receptacles of high amperage (20 amperes or more). Are there plugs available or will you need to add new lines and circuits? If you need to add wiring, when laying it out keep in mind that there’s no such thing as too many outlets in a workshop. The fewer (as in, ideally, zero) extension cords the better; they’re safety hazards. A good minimum is to have receptacles set at no more than six-foot intervals around the perimeter of the room, and, if possible, flush-mounted floor plugs in the central area.
Rockler Buffalo is proudly hosting the CNC Users Group! The club consists of CNC owners, users and prospective buyers. Every meeting consists of a ‘Show-n-Tell’ portion, demonstration and then a group discussion. We’d be happy to have you join us and we’ll be looking forward to seeing you at the store! Don’t miss out on this one of kind experience.

Just as a shed or garage can get stifling in the summer heat, winter cold can also make working conditions difficult — if not impossible. To prevent clumsy, stuff fingers from ruining your projects, you need a way to heat your workshop in even the most extremely frigid days of the year. A traditional residential space heater probably won’t cut it, as these are designed to heat single rooms. For a two-car garage or full basement, you’ll need something much bigger.

After a permit has been issued, the building inspector will want to be notified at various points during your build in order to do a site visit, walk around and inspect the details to make sure that they meet code requirements. These inspections are commonly at the point where excavation work is complete, when the foundation is completed but before back-filling, when framing and all structural work has been done, after the installation of the insulation and vapour barrier, and then a final inspection after everything is complete. You may need to have a separate plumbing inspector if you’re adding or changing plumbing fixtures, and electrical work will need to be inspected by the appro­priate electrical inspector (in Ontario, the Electrical Safety Authority). In my experience, inspectors appreciate good work, a clean, safe site, and are willing to work with hom­eowners and builders to make sure that the work will meet code and will endure.


With strength, sturdiness, and durability, maple is a common material for furniture for the bedroom and even china cabinets. Maple is moisture-resistant and frequently displays stand-out swirls in the wood grain, an aesthetically pleasing differentiator from other hardwoods. While most commonly a lighter color, maple also can take stains and paint well.[13]
The second corner of the triangle is in the center of the room and, in our case, is where the workbench is located. Following work progress in sequence, the workbench is typically the second workstation where medium-duty work is done after heavier preparatory or wood-milling steps are finished. The workbench is where work is typically done using hand tools or smaller power tools such as hand drills, routers and joinery tools.
I’m helping my son (who is significantly disabled) get started with a business idea that he had — one that I’d think was brilliant even if I weren’t his Mom — brilliant enough that I’ve “retired” from my law practice and moved us from MO to GA. Having lost 99.9% of ALL of my tools in the move (even the big ticket items, nearly 30 years collection — stolen by the mover!) I am now re-investing in tools, limiting my purchases to what we must have rather than all the fun stuff I used to have. . . .(So sad).
Pocket screws create a solid, simple-to-make joint. Because of the size and visibility of the hole, it’s usually located in areas that are concealed or rarely seen (though special plugs can be used to fill the holes.) Craig Sommerfeld, founder of The Kreg Tool Company, is credited with popularizing pocket screw joinery in the 1980s. The company today is the leader in creating the jigs, clamps and screws used to create pocket screw joints. Learn how to use a pocket screw jig in woodworking projects.
Hardwoods, botanically known as angiosperms, are deciduous and shed their leaves annually with temperature changes.[8] Softwoods come from trees botanically known as gymnosperms, which are coniferous, cone-bearing, and stay green year round.[8] Although a general pattern, softwoods are not necessarily always “softer” than hardwoods, and vice versa.[9]
For many of us, the moment we learned that a 2×4 board is actually 1.5 inches x 3.5 inches was simply mind-blowing. The reason for this apparent contradiction is that the board has been planed down to eliminate irregularities. At one point, many years ago, 2x4s actually were 2 inches x 4 inches, but their rough surfaces made them difficult to stock and handle. The old terms, such as 2×4 or 4×4, are still used, and are known as the “nominal” size of the board. These nominal sizes are used because they are easier to say and they stick to tradition. Now, thanks to a lawsuit, most big box stores list the nominal and actual sizes of lumber.

Chop saw (compound miter saw): I do a mix of woodworking from furniture to built-ins and even finish carpentry, and I find myself regularly using the chop saw. Even if used for nothing more than roughly cutting a long board into two shorter ones to fit in a car, this tool earns its keep. It is especially useful (with the help of an outfeed table) on long pieces that are precarious to push through a table saw. But, since a table saw with a jig can perform many of the same functions, this tool doesn’t make it to the essential list. With that said, I expect to have a chop saw wherever I am working, whether it be in the shop or at an install. If this was a post about on-site woodworking and trim carpentry, the chop saw might be the #1 tool.


I have never worked with my bench up against the wall, because I like to work from all 4 sides of my bench. I do like my machines pushed up against the wall and a large open space in the middle of the shop to facilitate easier movement. I have a Minimax combination machine so by necessity my tablesaw and jointer/planer are bundled together but I would actually prefer they not be (like a Felder machine that breaks apart). I would never put my tablesaw central in my shop, always at one end with a clear entry and egress for the sliding table, space permitting. Putting a tablesaw in the middle always struck me as one thing I’d always have to walk around and/or fight the temptation to stack stuff on it.

I have found that drawing everything to scale on grid paper is most helpful. That is what I am doing in preparation for my new shop. I will, however need to share that space from time to time with my wife’s hobby (hatching and raising chickens). Just a few in the spring till they get big enough to go outside. I am planning on a 26″ x 40″ building with infloor hydronic heat. Others have mentioned that you can’t have too much light, and I intend to use the 200 watt cfl’s to accomplish this, along with task lighting at each machine. Walls and ceiling will be painted white to reflect as much of that light as I can. I want to use the same type of floor treatment that Marc has used in his new shop. Marc, is it really expensive to do that? Or if a guy has never done that would it be better to hire out that job? Lumber storage I have not decided yet. I am fortunate that I am able to fell trees on our farm and have them cut up so I can stack and dry them. We have white oak, red oak, maple, cherry and pine. Although drying/storage will be in another building will still have to tote my boards around some.
For one thing, the rearrange-it-later approach may simply mean that once you’re set up, the haphazard plan becomes the permanent plan, thanks to sheer inertia (it is a pain to move furniture, after all, especially when some of it is as heavy and awkward as workbenches and stationary tools). For another, too little advance planning may mean you buy a power tool that’s too big for your space.

This will be a personal matter, depend­ing on whether it will be helpful for finishing or sharpening. However, it is a good idea to look beyond your current use of this space to the next owner. Would it be beneficial to add plumbing hookups so that the shop could someday be an apart­ment, or an art studio, or an extension to your house? It could add to the resale value of your house to be able to create as flexible an area as possible by roughing in a bathroom and even a kitchenette area if you can. If this is done when wall cavities are open or before the slab is poured, your forethought could pay dividends but not cost much up front. 
This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com.

Pocket screws create a solid, simple-to-make joint. Because of the size and visibility of the hole, it’s usually located in areas that are concealed or rarely seen (though special plugs can be used to fill the holes.) Craig Sommerfeld, founder of The Kreg Tool Company, is credited with popularizing pocket screw joinery in the 1980s. The company today is the leader in creating the jigs, clamps and screws used to create pocket screw joints. Learn how to use a pocket screw jig in woodworking projects.
Basically, I created a linear outfeed area, which includes the miter-saw station with folding wings, tablesaw with folding outfeed table, and my large router table, all in a line along the 20-ft. wall and set at the same height. The miter-saw station converts easily for use with a mortiser—with workpiece support on both sides—and it also accepts a minilathe. I even planned a location for all of the tools, blades, and jigs used with the tablesaw: on the operator side, for easy access.
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
Boat building Bow and arrow Bush carpentry Cabinetry Caning Carpentry Certosina Chainsaw carving Chip carving Clogs Ébéniste Fretwork Intarsia Japanese carpentry Khatam Kohlrosing Log building Marquetry Millwork Parquetry Pyrography Relief carving Root carving Sawdust Segmented turning Shingle weaving Shipbuilding Spindle turning Timber framing Treen Whittling Wood carving Woodturning Wood flour
With the right tools and materials, what you build is only limited by your imagination and creativity. So why not have a little fun with the kids and teach them something at the same time? Our woodworker tools and woodworking supplies will help you put together an easy birdhouse, squirrel feeder or butterfly house. The kids will love to use our paint samples to add their creative touch, and will enjoy displaying the finished product in the backyard.
Well you can only do so much with your given space. These guidelines are just general best-practices, but that certainly doesn’t mean everyone will be able to execute them to the letter. Even I make concessions for my personal situation. And yes, there would be differences in a Festool shop. I imagine everything would simply revolve around an MFT. :)
The progenitors of Chinese woodworking are considered to be Lu Ban (魯班) and his wife Lady Yun, from the Spring and Autumn period (771 to 476 BC). Lu Ban is said to have introduced the plane, chalk-line, and other tools to China. His teachings were supposedly left behind in the book Lu Ban Jing (魯班經, "Manuscript of Lu Ban"). Despite this, it is believed that the text was written some 1500 years after his death. This book is filled largely with descriptions of dimensions for use in building various items such as flower pots, tables, altars, etc., and also contains extensive instructions concerning Feng Shui. It mentions almost nothing of the intricate glue-less and nail-less joinery for which Chinese furniture was so famous.
One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at $50/sheet.
Other important power tools—A good jigsaw will help get you through many tasks, particularly cutting curves, that would otherwise require a bandsaw. Look for one with blade guides that keep blade deflection to a minimum. A handheld drill is also essential. A quality corded drill is much less expensive than a cordless one, and will never leave you without a charge. Also look for a quality random-orbit sander with a provision for dust collection.
The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ...  More + Product Details Close
I’m helping my son (who is significantly disabled) get started with a business idea that he had — one that I’d think was brilliant even if I weren’t his Mom — brilliant enough that I’ve “retired” from my law practice and moved us from MO to GA. Having lost 99.9% of ALL of my tools in the move (even the big ticket items, nearly 30 years collection — stolen by the mover!) I am now re-investing in tools, limiting my purchases to what we must have rather than all the fun stuff I used to have. . . .(So sad).
No matter what woodworking or tool-related venture you're taking on, Amazon.com has the trustworthy brands delivering the helpful products you'll want, brands like Dewalt, Makita, Stanley, Black + Decker, Festool, Shop-Vac, Jet and more. You'll also find a wide range of deals and special offers on woodworking products in the Deals and Savings page. Shop on Amazon.com and get free shipping for qualifying orders.
For many of us, the moment we learned that a 2×4 board is actually 1.5 inches x 3.5 inches was simply mind-blowing. The reason for this apparent contradiction is that the board has been planed down to eliminate irregularities. At one point, many years ago, 2x4s actually were 2 inches x 4 inches, but their rough surfaces made them difficult to stock and handle. The old terms, such as 2×4 or 4×4, are still used, and are known as the “nominal” size of the board. These nominal sizes are used because they are easier to say and they stick to tradition. Now, thanks to a lawsuit, most big box stores list the nominal and actual sizes of lumber.
A shop geared toward woodworking would have lumber storage located at one corner of the triangle. Storage space for wood — both long pieces and flat plywood pieces — should be adequate. Raised storage, such as racks or shelves mounted on the wall, must be sturdy. Wood storage should also be in close proximity to the stationary tools or machines (table saw, jointer, power planer, etc.) to avoid frequently carrying heavy wood across the span of the workspace. Wood storage should be handy and near the area where the heavy woodworking tasks will take place. Keep in mind that a considerable amount of space will be needed around stationary tools such as a table saws and jointers for manipulating large pieces of raw lumber.
If you live where summers get hot and humid, you may need more than a fan to keep cool in your workshop. Fortunately, air conditioners will both dehumidify and cool your space — and you don’t need a traditional window to get the job done. Instead of a residential window unit, consider a freestanding portable air conditioner that you can use as needed on hot days.
×