Click the image at right, and start building the ideal workflow at the bottom where you see the first red arrow. This arrow crosses through one roll-up door of a typical two-car garage. Note that if the right-hand window were not present, you could place lumber storage closer to the entrance, which would also allow for easier passage onto the jointer. Work flows from the jointer to the planer and the table saw, then ideally onto an outfeed table near position #2 in the diagram. From #2, proceed left to the assembly area (pictured below).
A clean well-organized environment is key to staying A clean well-organized environment is key to staying happy. The same goes for your desk. Keep the clutter at bay and organize all of your small essentials with the Dickies Work Gear 57012 Mug Organizer. Designed to fit over most mugs this clever caddy features 8 outer pockets and 6 ...  More + Product Details Close

There are benefits to either approach. Sharing a common wall with your house can require some careful soundproofing but can reduce heat loss and exterior fin­ishing costs like siding. A shop located in an addition is more likely to be allowed to have living space or storage space above it, and it may be easier to make use of the existing plumbing and electri­cal and heating systems of your home to service your shop space. Another advantage of an addition is not having to run to an outbuilding in minus-30-degree weather or a summer downpour.
Gone are the days when you could apply for a building permit based on a sketch on the back of a cigarette pack­age. In provinces like Ontario, design work must be undertaken by an insured designer registered under the provin­cial building code or by the owner of the property. You can do the drawings as the owner if you can demonstrate effec­tively through your drawings that your structure will comply with the techni­cal requirements of the building code in a clear and concise way. You will be required to submit detailed drawings, including the following:
Not long ago, I needed to make some angled wood parts to build a new soffit on my garage. I didn’t have the customary tool for the job, but I had some steel joining plates. I screwed through one of the holes in the plate, set my angle, then added another screw to lock the angle. I could then use it as a template to mark all the pieces at the same angle and cut them with my circular saw. — Ryan Bartsch
In the above video Will Myers teaches the basics of woodturning for woodworkers. He starts by showing how to prepare and center the wood, then discusses woodturning tools & parts of the lathe. And finally he begins roughing out a spindle for a classic cherry shaker candle table. This tutorial comes from the class and DVD: "Building the Hancock Shaker Candle Stand with Will Myers". If you'd like to build this historical candle stand along
Natural Light. Natural light is best, so any windows that offer illumination to the space should be put to good use. If you have little sunlight in your shop, locate your workbench so that its work surface gets whatever there is. Even the best eyesight is made better by good light, so the close work to be done on a benchtop benefits from the natural light.

In many workshops, band saws and drill presses are not used constantly, so they can be set back out of the way. Jointers and shapers can also sometimes be set back out of the midway, but keep in mind that the more trouble they are to reposition, the less useful they’ll be. Remember, too, that while jointers and shapers take up relatively little floor space, you need to allow space on either side that is at least the length of your longest workpiece: a four-foot workpiece needs about a ten-foot space (the tool, plus four feet on either side). The longer the pieces to be joined or shaped, the greater the space required on either side.


Old doors laid across sawhorses make great temporary workbenches, but they take up a lot of space when you’re not using them. Instead of full-size doors, I use bifold doors with hinges so I can fold them up when I’m done working. They’re also easier to haul around in the pickup for on-the-road jobs. — Harry Steele. Here are 12 more simple workbenches you can build.
I have a 3 car garage, 1-2 car bay, 1 single bay. I made some simple saddle brackets that hang on the outside of the garage door track (V shaped with the top of the V having a cleat that stabilizes the bracket against the top of the track, stove bolts hold the brackets to the track without interfering with the door). Through the bottom of the brackets are drilled holes to hold 3/4″ EMT metal conduit. This is available in 10 ft lengths which is enough to span the single bay track width. I used cotter pins to hold the conduit in the brackets. Eye bolts that slide over the conduit can then be mounted to a 2 bulb flourescent light fixture and bingo, you have lighting that works with the garage door up or down. I did this for my single bay which is where I have my tablesaw and bench/outfeed table. I centered the light at the tablesaw/outfeed table juncture and it makes for awesome lighting for both surfaces.
A kind’a unrelated question. I just finished building the lumber storage rack/sheet goods cart from your “racking my brain..” video. I see you went with the metal wall storage rack in your new shop (which I would love also, just can’t afford) but, I was curious why you didnt put another sheet goods cart. Previously I had the stand up sheet goods storage box like I see your current pictures but, from what little I have used the cart, I like it better than the stand up storage. Its easier to get things in and out and see what all I have. The only draw back is that I can’t store as much on the cart as I could with the box storage.
Each entry must feature some kind of inlay. This can be wood, glass, metal, etc. Epoxy pours are not allowed per /u/kevin0611's request. An epoxy pour does not count as an inlay for the sake of this contest. (Example would be cutting a pattern on CNC or by hand then filling with a colored epoxy to give the illusion that it's inlay.) Bowties, marquetry, and banding are good examples of allowed inlay in this contest.
This will be a personal matter, depend­ing on whether it will be helpful for finishing or sharpening. However, it is a good idea to look beyond your current use of this space to the next owner. Would it be beneficial to add plumbing hookups so that the shop could someday be an apart­ment, or an art studio, or an extension to your house? It could add to the resale value of your house to be able to create as flexible an area as possible by roughing in a bathroom and even a kitchenette area if you can. If this is done when wall cavities are open or before the slab is poured, your forethought could pay dividends but not cost much up front. 
First, let’s take a look at four placement options for the table saw, the machine that is at the heart of most woodshops. The first option (see the illustration) places it in the center of the shop, which lends maximum space and flexibility for ripping and panel sawing, as well as crosscutting long boards. The main requirement here is a shop that’s at least long and wide enough to allow room for the workpiece, both on the infeed and outfeed sides.
×