Along with stone, clay and animal parts, wood was one of the first materials worked by early humans. Microwear analysis of the Mousterian stone tools used by the Neanderthals show that many were used to work wood. The development of civilization was closely tied to the development of increasingly greater degrees of skill in working these materials.
Fir, also known as Douglas Fir, is very inexpensive and common at local home centers. It has a characteristic straight, pronounced grain with a red-brown tint. However, its grain pattern is relatively plain and it does not stain well, so Fir is commonly used when the finished product will be painted. While commonly used for building, this softwood would also be suitable for furniture-making as well.[12]
If you want to run a business operated by yourself and more than one employee, you may run into zoning issues if your location is zoned for residential use only. It’s common for municipalities to allow and encourage home-based busi­nesses but there will likely be a maximum area that you will be permitted to add for business purposes. If you try to build a shop that will contribute noise and traffic (from employees or deliveries) to an urban neighbourhood, you run the risk of run­ning into opposition from neighbours concerned by the impact your shop will have. Your municipality will have planners with whom you should consult as you begin to define the possibili­ties that your property will allow.

A receptacle or circuit that is overloaded is a hazard, in particular one fused beyond its limits. Power tools, especially heavy-duty saws, require lots of amperage, and you may need to add a circuit or two to serve the increased demand in your workshop space. Some tools re­quire 220-volt service, so you may want to install a special plug and line to power that high-powered table saw.


Along the opposite long wall are the planer, combination sander, drill press, bandsaw, workbench, and compressor. Each tool has dust-collection hookups and storage space to keep the relevant tools, bits, blades, and fixtures nearby. The planer is the only tool I have to roll out into the middle of the room to use, which takes about a minute, including connecting the dust-collection hose.
A landscape designer friend of mine tells a story about the college he went to. During his years there, the university embarked upon an ambitious building plan, adding several large structures around the main quad: a dorm, a chemistry lab, and a couple of others. The look of the place, which had remained unchanged for a century, was suddenly transformed, as glass-and-steel modernist structures were interspersed with the earlier ivy-covered stone Victorian-Gothic.
Your sense of space and how to use it will be slightly different depending on the focus of your craft. If you are building furniture with hand tools, you will be able to make do with less space (under 300 sq ft.) than if you’re using mainly power tools and building sets of cabinets (over 400 sq ft.). Some 3D mod­elling with a program like Sketch-Up or some 2D layouts on graph paper with scaled cutouts can allow you to experi­ment with arranging your space and how much of it you will need. You should include not only the tools, benches and storage that you currently possess but also enough room to tackle new types of projects and new tools that you antici­pate needing down the road. When you think you have a layout that works, test it out by mentally working through a range of different projects you might tackle and the needs you will have for material storage, assembly and finishing. Then revise as necessary; this process will allow you to hone in on a general square footage and layout ideas that will set you up to move forward.
Marc, would not assumptions for a Festool shop differ considerably? Far fewer big machines, and more carrying lightweight precision machines to the wood, for example. I only have a few Festool machines so far (took quite a while to get past the sticker shock), but I am beginning to see how it could change the way we work. My 400 sq ft shop is getting awfully crowded with floor-standing machines and implementing your guidelines, sound as they are, is difficult.
Gone are the days when you could apply for a building permit based on a sketch on the back of a cigarette pack­age. In provinces like Ontario, design work must be undertaken by an insured designer registered under the provin­cial building code or by the owner of the property. You can do the drawings as the owner if you can demonstrate effec­tively through your drawings that your structure will comply with the techni­cal requirements of the building code in a clear and concise way. You will be required to submit detailed drawings, including the following:
These are all good tips, and apply to pretty much every shop. Like all things woodworking they need to be tweaked so that it’s right for the individual. For instance, I have a basement shop that’s not tiny but it is still space constrained, so worrying about the optimal layout for my ts/jointer/planer is a little off the mark since I don’t have to walk very far; instead, I want to be sure that related tools can be used *at the same time*. Having to move the planer out of the away so that I can use my TS is crazy if it can be avoided. However, interference between my drill press and my planer is less of an issue because they usually don’t get used at the same phase of a project.

Before you buy a single tool, you need to take a hard look at your workshop space. If your workshop is a freestanding building or empty barn, you can simply measure the perimeter and know that you have the entire square footage at your disposal including the wall space. If your workshop is tucked into the back of a garage or a corner of partially finished basement, you’ll need to plan your furnishings with cars and water heaters in mind.
If you have to pick up long lengths of wood from the lumberyard, throw a spring clamp in the back of your vehicle. Use the clamp to attach the warning flag to the end of the protruding lumber. The clamp’s easy to slip on and off, and you won’t have to fuss around with staples, nails or string. — Steve Parker. Plus: Learn more about how to transport large items in your truck.
Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.
In this video James Huggett shares a very detailed tutorial on how to cut a  half-blind dovetail joint with hand tools, for use on drawers and case pieces. Jim has cut many dovetails over the years, and here are some of the lovely dovetailed drawers that Jim has made using this half-blind dovetail joint: Notice the deeply scribed layout line on these drawers. That, along with irregular and more delicate pins, are a sure sign
The dream of a dedicated home shop is a common one among woodworkers. Whether you currently borrow shop space, work in your driveway or side yard, or compete for a corner of your basement with Christmas decorations or your fur­nace, you may be ready to build your own space that will allow you the free­dom of more room and time, and will also keep dust, fumes, and noise under control. Every design/build situation will be unique but there are a series of consid­erations that you will face in the design and construction phases of your project. Let’s walk through the process and dis­cuss the questions that you will need to ask yourself and others as you approach this project.

Depending on your situation, you may need to upgrade to 200 amp electrical service in order to meet the needs of your house and your shop. It may also be in your interests to add in a separate electrical service meter on your shop so that you can clearly write off electrical use for your business, or in future rent the space out and clearly separate out the utilities for bill­ing your tenant. Generally, you don’t want to skimp on the power to your shop or on the lighting you include.

Hey Marc. I’m sure you may have said it somewhere when you were building your fine shop, but, I wanted to know if that gray flooring in your shop is one of those rubber flooring deals. It looks like a small sample I just got in the mail the other day. It is rubber, but, almost feels like plastic, and looked like the same color as your floor. Thnx in advance.
To make the most of your workshop oasis, look for a water dispenser that offers a choice between chilled and hot water. This will let you enjoy a cold, refreshing drink in the heat of summer rather than a lukewarm bottle that’s been sitting around gathering dust. You’ll also cut down on the amount of plastic your household goes through, which is a boon for the environment. In the winter, the hot water tap will also you to make a cup of tea or a mug of instant coffee on the spot. No matter what your taste, a versatile drink dispenser will keep you hydrated and happy while you work.
The planners did an interesting thing, my friend recalls. Instead of commissioning a hugely expensive study to try to predict the new patterns that would result from the opening of the new buildings, rather than devising an anticipated program and laying out a new scheme, the university’s brain trust decided to let the students and faculty, the lifeblood of the university, shape their own arterial flow.
That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000.
If a poured cement floor prohibits the installation of plug receptacles flush to the floor and you elect to surface-mount a plug, protect the exposed feed wire. A piece of one-by-four stock with a groove cut in its underside and its top edges chamfered, will pose little more tripping risk than a threshold. However, paint its protective covering a bright color to remind you and any other visitors to your shop of its presence.

In most small shops, once the key machines are in place, others are arranged wherever there is room for them. There typically isn’t enough free space for these tools in the middle of the floor area, although sometimes you can tuck a machine into an unused space. For example, in a shop where the table saw is in the center, a shaper (or a router table or spindle sander) with a table the same height as the saw can be put on the outfeed side of the extension table (see the illustration). Also, building a router table directly into the table saw’s extension table is a great way to save space, as well as make use of the saw’s fence for routing operations.
×