Timely article indeed. I’ve been playing with the shop layout tool on Grizzly’s website (http://www.grizzly.com/workshopplanner) which helps you see how tools fit in a specific shop size. However, your insight and experience really helps with ergonomic considerations. When I first built my shop, the first thing I did was installing a wall mounted work bench – as my fore fathers had all done – Big Mistake! Soon-to-be project: ripping it out and building a mobile work bench on wheels (like the one you have pictured).
To experiment with different wood shop layouts, measure your furniture and equipment to sketch onto your plan in different positions. You can also make cutouts of the footprint of your items so you can easily move them around your floor plan to see how best to arrange them. As you do so, don’t forget to leave adequate spacing around tools and tables.
I place the band saw first in my order of purchases, because I consider it the heart of the shop. Band saws are very safe tools for ripping, re-sawing, cutting curves and more because all of the force is downward, virtually eliminating any chance of unexpected kickbacks. I wanted a saw that had a strong back, dynamically balanced cast iron wheels for smooth operation and flywheel effect, 12" depth of cut, good dust extraction design, a large table and a solid fence. After shopping around, I settled on the General International Model 90-170 14" saw. It is very smooth, comes with an Excalibur fence, and it is light enough (133kg) to move into your basement without crushing someone.
I consider it part of my job to answer emails from my fellow woodworkers. Guild members or not, everyone receives a response. Occasionally, I get a question that requires a very detailed answer and that answer in and of itself would make for a decent blog post. That happened this morning when a Guild member asked me for advice on shop layout. I brainstormed some basic tips that I think apply to nearly all wood shops (at least the ones that incorporate some power tools). Of course, shop layout is something that evolves over time and really comes down to one’s personal preferences and tool choice. But here are some simple rules of thumb that came to mind; some more obvious than others. If you have some tips to add, please do so in the comments!
Cutting sandpaper is a quick way to dull your scissors or utility knife blade. Instead, I fastened a hacksaw blade to the edge of my workbench. I slipped a washer behind the blade at each of the mounting holes so a sheet of sandpaper to easily slides in behind the blade. I fold the paper where I want to cut, just as a reference. — Kim Boley. Try some of these storage solutions!
If you have a fixed-in-place cutoff saw (a radial-arm, miter saw, or sawbuck, for example), it can, unlike the table saw, be conveniently positioned against a wall. Don’t set it in a corner, however, as you’ll need space on either side of the blade. Figure into your plan a two-foot-deep, three-foot-wide space for the saw itself and tables or other supports flanking the tool. Allow enough space directly in front of the saw for the operator to be able to comfortably line up and operate the saw.
When it comes to woodworking for beginners, there are 6 things that I think are essential to know for how to start woodworking. I’m going to discuss each of these tips in hopefully a really simple way to make it a breeze to understand, so you can get to the fun part of actually starting to woodwork! I wish when I started and was learning how to woodwork that I had a simple beginner tips guide like this one!
Commonly used woodworking tools included axes, adzes, chisels, pull saws, and bow drills. Mortise and tenon joints are attested from the earliest Predynastic period. These joints were strengthened using pegs, dowels and leather or cord lashings. Animal glue came to be used only in the New Kingdom period. Ancient Egyptians invented the art of veneering and used varnishes for finishing, though the composition of these varnishes is unknown. Although different native acacias were used, as was the wood from the local sycamore and tamarisk trees, deforestation in the Nile valley resulted in the need for the importation of wood, notably cedar, but also Aleppo pine, boxwood and oak, starting from the Second Dynasty.
Examples of Bronze Age wood-carving include tree trunks worked into coffins from northern Germany and Denmark and wooden folding-chairs. The site of Fellbach-Schmieden in Germany has provided fine examples of wooden animal statues from the Iron Age. Wooden idols from the La Tène period are known from a sanctuary at the source of the Seine in France.
Before you buy a single tool, you need to take a hard look at your workshop space. If your workshop is a freestanding building or empty barn, you can simply measure the perimeter and know that you have the entire square footage at your disposal including the wall space. If your workshop is tucked into the back of a garage or a corner of partially finished basement, you’ll need to plan your furnishings with cars and water heaters in mind.
Marc, would not assumptions for a Festool shop differ considerably? Far fewer big machines, and more carrying lightweight precision machines to the wood, for example. I only have a few Festool machines so far (took quite a while to get past the sticker shock), but I am beginning to see how it could change the way we work. My 400 sq ft shop is getting awfully crowded with floor-standing machines and implementing your guidelines, sound as they are, is difficult.
How do you divide 11-3/8-in. (or any other mathematically difficult number) into equal parts without dividing fractions? Simple. Angle your tape across the workpiece until it reads an easily-divisible dimension and make your marks with the tape angled. For example, say you want to divide an 11-3/8-in. board into three equal parts. Angle the tape until it reads 12-in., and then make marks at “4” and “8”. Plus: More measuring tips and tricks.
With these three power tools (and a few hand tools), I feel like I could make about 80% of the jobs that come through my shop on a daily basis. Obviously, some jobs will require more specialized power tools to complete, but these three probably find their way into almost all of my work. With that said, there are a few other tools that I couldn’t imagine being without and I feel need to be added to the list.
Temperature and Moisture Control. If your workshop is to be located in a portion of your house that is already comfortably warm, this will not be an issue. But if you’re converting a barn or shed or an unheated space, especially if you live in a climate where winter temperatures make for cold hands, you’ll need to devise a heating strategy. In some climates, air conditioning is a virtual necessity in hot weather.
Instead of using a container to mix a small amount of epoxy, just make a mixing surface on your workbench using painters tape. Simply lay down strips, overlapping the edges so the epoxy doesn’t get on your bench. When you’re done, peel off the tape and throw it away. This mixing surface will work for more than just epoxy, you can use it for wood glue or any other material you need easy access to while working on a project.
If you work with rough lumber, a planer will be absolutely necessary, except for the most rustic of projects. Every piece of rough cut lumber ends up somewhat not straight, not flat and not consistent in thickness, either from variations during the sawing or from stresses which occur while the wood dries. The planer, combined with the jointer, is a one-two punch to remove these variations and produce straight, flat and consistently thick lumber. The reason the planer is ahead of the jointer on this list is that some lumber is straight enough and flat enough to plane without jointing if the job is a little less finicky, thereby skipping the jointer.
There are many factors to consider when deciding what type of wood to use for a project. One of the most important is the workability of the wood: the way in which it responds when worked by hand or tools, the quality of the grain, and how it responds to adhesives and finishes. When the workability of wood is high, it offers a lower resistance when cutting and has a diminished blunting effect on tools. Highly workable wood is easier to manipulate into desired forms. If the wood grain is straight and even, it will be much easier to create strong and durable glued joints. Additionally, it will help protect the wood from splitting when nailed or screwed. Coarse grains require a lengthy process of filing and rubbing down the grain to produce a smooth result.
Low-tech tools are high on value A basic set of handplanes lets you true edges, flatten panels or wide boards, and achieve finish-ready surfaces. Start with a small cluster of handplanes—low-angle and standard block planes, a No. 4 or 4-1/2 bench plane, and a jointer plane. A set of inexpensive chisels is essential for chopping, paring, and trimming.
Shops have value on many different levels. There is the satisfaction of having a place to create and work on projects that is hard to quantify, but definitely improves your quality of life. There is the value to your small business of having space in which to work wood and thereby generate income. There is the dollar value of the build itself, which will be a considerable investment and, finally, there is the resale value of your property after you’ve added your shop. Before you go too far, though, it’s worth asking a local real-estate agent about the potential return on your investment in your area; generally shops won’t add significantly to the value of your property, so it’s worth thinking carefully about what else the space could be used for if you were to sell. The decision about whether it is worth it to build is a matter of balancing all these factors: projected sales balanced against the cost; the cost of building is balanced against what it will be worth when you sell. Woodworking can be a creative outlet, can give you a sense of mastery, and even be a way to give back to your community by donating beautiful pieces to local charities for fundraising auctions, or creating pieces that future generations will inherit. Ultimately, the value of a shop might come down to the emotional and social returns that it will pay you and the people around you for years to come.
Impact driver: I am a giant fan of impact drivers. I have been using them for a while now and can’t really remember my life before them (Click here to read more about my introduction to impact drivers). This is the one tool that I always have with me, and I expect to be within easy reach. So much so, that I own three of them and could imagine myself with a couple more. Like the chop saw, if this was a list of on-site or installation tools, the impact driver would be near the top.
Figure out a simple setup for your woodworking space. You don’t need a fancy and expensive workshop or garage to start woodworking. In fact, we’ve never had a workshop or garage (though I do dream of having one haha). In our current town home, we always setup a temporary workshop table in our backyard with a pair of sawhorses and a plywood board from the home improvement store.
Second is the operating space around the machine. When the table saw is used to cut a piece of four-by-eight-foot plywood, the tool space increases geometrically, as the thirty-two-square-foot sheet of stock is pushed and pulled through the blade. Even if you’re not planning on using your table saw to cut plywood, you need to allow ripping and crosscutting space. This means that in front of and beyond the blade, you need distances at least as great as the length of the longest board you’ll need to rip; and that you’ll require space for cutoff work on either side of the saw.
From felling the trees through installation of the final piece Scott Wunder, owner of WunderWoods in St. Charles, MO, shares his woodworking knowledge with anyone that will talk to him about wood. Whether you want to learn about milling lumber or need help on a project, get your fill of woodworking infotainment at WunderWoods.com. Scott writes about all aspects of woodworking and specializes in finishing (mostly because no one else likes to sand).
Whether you’re a seasoned woodworker or DIY pro, you’ll find the woodworking tools you need for the jobsite or around the house. Search woodworking project plans to get some fresh ideas or browse our wide tool selection to find exactly what you need. Outfit your woodworking shop with routers, sanders, table saws, dust collectors, planing tools, and hand tools from bestselling brands including Makita, Festool, Bosch, JET, Powermatic, Rockler, Grizzly, and more.
Among early finds of wooden tools are the worked sticks from Kalambo Falls, Clacton-on-Sea and Lehringen. The spears from Schöningen (Germany) provide some of the first examples of wooden hunting gear. Flint tools were used for carving. Since Neolithic times, carved wooden vessels are known, for example, from the Linear Pottery culture wells at Kückhofen and Eythra.
In addition to sheer power, look for a model with a built-in thermostat so you can set it and forget it. This convenience feature is well worth it so you don’t have to stop what you’re doing mid-project to manually turn your heater on and off to maintain your desired temp. A good garage heater will mount to the wall or ceiling to save space and will come with a durable housing and full safety screen to keep dust and wood chips from reaching the heating elements and starting a fire.