Here’s a safe and sound way to make long cuts with a circular saw on plywood clamped to a worktable. Cut about 12 in. into the plywood, then twist a piece of duct tape into a bow tie, with up-and-down adhesive faces. Slide it in the saw kerf and press the tape down above and under the plywood. Now as you finish the cut, the trailing end can’t curl down dangerously as you saw. Hats off to Mike Connelly for simplifying this job. Check out how to make this DIY duct tape wallet.

Radial-arm saws, sliding compound miter saws, and powered miter boxes (chop boxes) used for crosscutting long boards are best located against the longest wall of the shop, as shown in the first option in the illustration. If the saw is to become a stationary machine, it’s typical to mount or build it into a long, narrow support table fitted with a fence.


Here’s a nifty tip—with a nifty tip—from faithful reader Don Ayers: Fill snap-capped sports water bottles with glue and stick them upside down in a hunk of 2×6. Now you don’t have to wait for the glue to run into the neck of the bottle, and the cap will control glue flow (and never get lost!). To holster the glue dispensers, cut holes in the base with a spade bit that’s a smidgen larger than the cap’s diameter.

Any serious woodworker knows that square and flat Any serious woodworker knows that square and flat stock is the key to producing fine work so it’s time to skip the hand tools and graduate to the JJ-6HHDX 6 in. long bed jointer. This beast boasts a helical insert cutter head with staggered carbide inserts yet runs quietly and ...  More + Product Details Close


Always nice to see project ideas. Yet, to make a living while woodworking all projects need to be scaled up so that one can actually earn enough to survive and compete against the flood of Chinese imports and others. Substitute products made from plastic, metal or wood are a common place and normally cheaper due to mass production and human rights violations. Politicians don’t care about the disappearance of many of America’s Cottage Industries and most consumers don’t care as well.
This simple jig makes laying out circles a breeze. Drill a 1/8-in. hole through every inch mark on a ruler or yard-stick. To draw a circle, place a pin through the number “1” into the center of your board. Add 1 in. to the radius of the circle you wish to draw, and insert a pencil into this number. Using the pin as a pivot, rotate the pencil to mark the circle. — Edwin Constantino. How to Cut Curves in Wood
I looked around at many versions of Taiwanese drill presses. I ended up purchasing the Ridgid DP15501 15" drill press because I liked the way the quill stop was made, the work light, key stor­age, and the easy access to the belt change system. This machine was also on sale when I needed it, so that made it a slam dunk. Choose the one that suits you, as they’re all very similar. The table is large enough, and the distance to the column is large enough to allow you to do most anything a small shop needs. 
Among early finds of wooden tools are the worked sticks from Kalambo Falls, Clacton-on-Sea and Lehringen. The spears from Schöningen (Germany) provide some of the first examples of wooden hunting gear. Flint tools were used for carving. Since Neolithic times, carved wooden vessels are known, for example, from the Linear Pottery culture wells at Kückhofen and Eythra.
For one thing, the rearrange-it-later approach may simply mean that once you’re set up, the haphazard plan becomes the permanent plan, thanks to sheer inertia (it is a pain to move furniture, after all, especially when some of it is as heavy and awkward as workbenches and stationary tools). For another, too little advance planning may mean you buy a power tool that’s too big for your space.
Clamping up four mitered corners is tricky. You can buy specialty clamps for this, but I make my own. Here’s how to do it. Start with a long 1×4, as it’s easier (and safer) to clamp for making the angled cuts than a short piece. Mark out the blocks, and then drill a 1-in. diameter hole in the center of each one. The hole prevents the blocks from getting glued to your project. Cut 45-degree angles tangent to the hole, and then cut the blocks free from the long board. We’ll walk you through how to make one for your home shop.

With the right tools and materials, what you build is only limited by your imagination and creativity. So why not have a little fun with the kids and teach them something at the same time? Our woodworker tools and woodworking supplies will help you put together an easy birdhouse, squirrel feeder or butterfly house. The kids will love to use our paint samples to add their creative touch, and will enjoy displaying the finished product in the backyard. 

One of the misconceptions about planers is that they make lumber straight. They do some straightening, but they don’t make lumber straight. That is what jointers do. Many lumber mills just send rough lumber through the planer allowing the board to exit the machine with the same ups and downs and whoops that is entered with, only now to a consistent thickness. This is especially apparent when gluing up a couple of these roller coaster type of boards and trying to get them to line up. After a couple of those glue-ups, you will swear by lumber that has seen the jointer before the planer, and never skip the jointer.

A clean well-organized environment is key to staying A clean well-organized environment is key to staying happy. The same goes for your desk. Keep the clutter at bay and organize all of your small essentials with the Dickies Work Gear 57050 Mug Organizer. Designed to fit over most mugs this clever caddy features 8 outer pockets and 6 ...  More + Product Details Close


Much like the assembly table, nearly every project in my shop makes extensive use of the table saw. And like it or not, my outfeed table becomes a second storage area for project parts and cut-offs. So I like to have mine located in the middle of the shop for the same reasons as the assembly table. Additionally, it’s nice to have ample space around the tablesaw for those larger workpieces. Unless it’s absolutely necessary, I’m not a fan of storing the table saw against a wall.
If you work with rough lumber, a planer will be absolutely necessary, except for the most rustic of projects. Every piece of rough cut lumber ends up somewhat not straight, not flat and not consistent in thickness, either from variations during the sawing or from stresses which occur while the wood dries. The planer, combined with the jointer, is a one-two punch to remove these variations and produce straight, flat and consistently thick lumber. The reason the planer is ahead of the jointer on this list is that some lumber is straight enough and flat enough to plane without jointing if the job is a little less finicky, thereby skipping the jointer.
Your sense of space and how to use it will be slightly different depending on the focus of your craft. If you are building furniture with hand tools, you will be able to make do with less space (under 300 sq ft.) than if you’re using mainly power tools and building sets of cabinets (over 400 sq ft.). Some 3D mod­elling with a program like Sketch-Up or some 2D layouts on graph paper with scaled cutouts can allow you to experi­ment with arranging your space and how much of it you will need. You should include not only the tools, benches and storage that you currently possess but also enough room to tackle new types of projects and new tools that you antici­pate needing down the road. When you think you have a layout that works, test it out by mentally working through a range of different projects you might tackle and the needs you will have for material storage, assembly and finishing. Then revise as necessary; this process will allow you to hone in on a general square footage and layout ideas that will set you up to move forward.

Each entry must feature some kind of inlay. This can be wood, glass, metal, etc. Epoxy pours are not allowed per /u/kevin0611's request. An epoxy pour does not count as an inlay for the sake of this contest. (Example would be cutting a pattern on CNC or by hand then filling with a colored epoxy to give the illusion that it's inlay.) Bowties, marquetry, and banding are good examples of allowed inlay in this contest.
Gone are the days when you could apply for a building permit based on a sketch on the back of a cigarette pack­age. In provinces like Ontario, design work must be undertaken by an insured designer registered under the provin­cial building code or by the owner of the property. You can do the drawings as the owner if you can demonstrate effec­tively through your drawings that your structure will comply with the techni­cal requirements of the building code in a clear and concise way. You will be required to submit detailed drawings, including the following:
In a woodworking shop, lumber storage is key, and it’s best to design shelves or racks that are about 50 percent larger than you think you need — you’ll almost certainly acquire more materials as the years go on. To maximize a small space, use walls by mounting shelves to the ceiling and purchasing a sturdy step ladder to help you reach things. A wall covered in standard pegboard and outfitted with hooks allows you to customize hand tool storage and keep your most-used hardware within easy reach.
×