Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.
Let’s face it, one of the most significant costs of your shop will be its foundation. While you’re at it, what about adding space above your shop? There may be regulations preventing you from building living space above your shop if it is in an urban setting or in an outbuilding, but there may be some flexibility depending on where you live. It is in the municipality’s interests to encourage infill housing that uses existing infrastructure. At a minimum, think about including attic trusses to create some space above your shop for drying lumber or storing equipment. Access could be from simple pull-down attic stairs or from the exterior if you don’t want to lose floor space to a stair or ladder. If you’re creating an addition to your house, you may be able to add a couple of rooms you’ve always wanted, such as a family room, office or in-law suite.
The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at $50/sheet.
If your shop will be attached to your house or another structure, it will likely need to match its foundation, tying the two structures together so that one does not structurally stress the other if they shift differently. That may dictate a poured concrete or concrete block foundation. Regardless of your foundation type, a cold concrete floor will sap energy away from the rest of the structure if you are not careful, so think about how to insulate it well before you build.
Old doors laid across sawhorses make great temporary workbenches, but they take up a lot of space when you’re not using them. Instead of full-size doors, I use bifold doors with hinges so I can fold them up when I’m done working. They’re also easier to haul around in the pickup for on-the-road jobs. — Harry Steele. Here are 12 more simple workbenches you can build.
I’m helping my son (who is significantly disabled) get started with a business idea that he had — one that I’d think was brilliant even if I weren’t his Mom — brilliant enough that I’ve “retired” from my law practice and moved us from MO to GA. Having lost 99.9% of ALL of my tools in the move (even the big ticket items, nearly 30 years collection — stolen by the mover!) I am now re-investing in tools, limiting my purchases to what we must have rather than all the fun stuff I used to have. . . .(So sad).
Chop saw (compound miter saw): I do a mix of woodworking from furniture to built-ins and even finish carpentry, and I find myself regularly using the chop saw. Even if used for nothing more than roughly cutting a long board into two shorter ones to fit in a car, this tool earns its keep. It is especially useful (with the help of an outfeed table) on long pieces that are precarious to push through a table saw. But, since a table saw with a jig can perform many of the same functions, this tool doesn’t make it to the essential list. With that said, I expect to have a chop saw wherever I am working, whether it be in the shop or at an install. If this was a post about on-site woodworking and trim carpentry, the chop saw might be the #1 tool.
I saw in the March 2019 Vol36,No.1 Iss 259. I have 2 Christian people very close to me that could likely be getting married soon . When I saw the unity cross on page one this would be the perfect gift from a parent. I would like to make it but need the plans. I do not need 3,000 or 60,000 plans I just wish to purchase the plans for the unity cross. I am a beginner so I need detail plans. Please send me information on ordering just the unity cross plans and where to purchase giant Sequoia and white oak woods. Thank you in advance for your help. I need the plans and information before April.
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strapping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.
Some types of wood filler can be hard to get off your hands after they dry, especially if you use your fingers to push it into small cracks and holes. When that happens, I reach for fine grit sandpaper and sand it off my fingers. It’s great for removing dried-on polyurethane glue and canned foam from your hands, too. — Chris James. We’ve got great solutions for removing super glue, too.
Popular and easy to work with, cherry is in high demand for its reddish-brown color and ease of staining and finishing. Cherry likely won’t be at the local home center, but should be at a lumberyard for a somewhat expensive price. This hardwood is a very common material for furniture, and is resistant to normal wear-and-tear, but it is best for indoor pieces.
Temperature and Moisture Control. If your workshop is to be located in a portion of your house that is already comfortably warm, this will not be an issue. But if you’re converting a barn or shed or an unheated space, especially if you live in a climate where winter temperatures make for cold hands, you’ll need to devise a heating strategy. In some climates, air conditioning is a virtual necessity in hot weather.
Examples of Bronze Age wood-carving include tree trunks worked into coffins from northern Germany and Denmark and wooden folding-chairs. The site of Fellbach-Schmieden in Germany has provided fine examples of wooden animal statues from the Iron Age. Wooden idols from the La Tène period are known from a sanctuary at the source of the Seine in France.
My shop ended up being 23 x 19 feet, for a total of 437 square feet. I put my wood rack in the basement, but outside the walled in shop area. To keep the dust in the shop, a three part strategy was employed. I have a dust collection system, an air filtration system and a shop vacuum for cleaning dust out of machinery. I put up new walls, installed new electrical service, lighting, and two access doors for ease of materials movement. The shop includes two windows so that I can enjoy natural light, and not feel like I am squirreled away in the basement.
With two varieties, red and white, oak is known to be easy to work with and relatively strong. However, furniture makers often opt for white oak over red oak for its attractive figure and moisture-resistance. Depending on the kind needed, oak can probably be found at a local home center or a lumberyard for a bit pricier than other hardwoods.
If your table saw is near a wall and your shop is fairly narrow, positioning the jointer and planer against the opposite wall is reasonable, as shown in option 2 in the illustration. If the shop isn’t long enough to accommodate long workpieces, try to put these machines near an operable doorway, as shown in the illustration and in the photo of Doug Warren’s shop.