If you work with rough lumber, a planer will be absolutely necessary, except for the most rustic of projects. Every piece of rough cut lumber ends up somewhat not straight, not flat and not consistent in thickness, either from variations during the sawing or from stresses which occur while the wood dries. The planer, combined with the jointer, is a one-two punch to remove these variations and produce straight, flat and consistently thick lumber. The reason the planer is ahead of the jointer on this list is that some lumber is straight enough and flat enough to plane without jointing if the job is a little less finicky, thereby skipping the jointer.
Line ’em up — Most other woodshop machines work harmoniously when lined up along the walls, where they are easy to power and connect to dust collection. The amount of space left between these tools depends on the amount of room you have, the size of the stock you work with, and whether or not adjacent tools have tables at the same height. You can always pull a machine away from the wall if additional space is needed. Clearly, these options are not the only possibilities and are contingent upon the mix of machines you have, the shape and size of your shop, and the kind of work you do. The bottom line is if the layout works for you, then that’s the best for your shop (and don’t let anyone tell you any different!).
The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.
I really appreciate the article. I am always looking for a way to improve my shop and its layout. I currently have a 34′ x 28′ garage which I park two vehicles and still have some room for a table saw, large bench and various smaller benches and cabinets. All of my large power tools are on casters so I can roll them out when I move the cars outside. Right now I am considering keeping my little truck outside permanently and set the shop up more in a fixed layout. This would make working in the shop more enjoyable and much easier to do more complex projects that I currently take on. Maybe this spring. Thanks for the advice.
Plan to invest in a set of bench chisels, both standard and low-angle block planes, a No. 4 or 4-1⁄2 smoothing plane, and a No. 6 jack or No. 7 jointer. Between them, these planes will true edges, flatten glue-ups that are wider than your thickness planer, and tame tricky grain that would tear out with a mechanized planer. They also do fine trimming better than any other tools.
I agree with all of these tips in a larger shop. In a smaller shop (mine is just under 400-square feet) most things are fairly close together anyway. One of my original principals for shop layout was … how is a machining process performed on a piece of wood? Is the wood stationary while it is machined … or does the wood move through the machine? If the wood is stationary, I have tried to have this set for one side wall of the shop. To be specific, I have four machines in one line with a continuous table to support long pieces that might need cutting from one or all of those machines. The machines in that line are (from left to right) the drill press, the powered miter saw, the square-chisel mortiser and the radial arm saw.
I added an accessory mitre gauge to the saw for accurate cut-off work. The Incra Miter1000 showed up under the Christmas tree after the Lee Valley flyer photo with part number mysteriously ended up on the fridge door with a circle around it last December. A great addition, the Incra is light, accurate, and provides adjustable stops for cutting multiple parts to precise length. I will also make a plywood cut-off sled for the saw for squaring larger panels.
With an orbital sander and good sandpaper you can smooth wood evenly and easily with first-class results. When flush-sanding solid edge-banding, draw a squiggly line across the joint before sanding. The edge-banding will be slightly proud of the plywood veneer, so the pencil marks provide a visual aid to make sure that you’re sanding flat, and that you don’t sand through the plywood’s veneer. As you go, you can also test for a smooth, level transition by gently scraping your fingernails against the transition. If it’s smooth, your fingers will not catch on the seam between the two pieces
The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ... More + Product Details Close
If your shop is long and narrow, option 2 provides maximum space to the left of the fence for handling large sheets of plywood. If you often work with full sheets of plywood or other sheet goods, you might want to build the table saw into an extension table surround, as San Diego woodworker Pat Curci did in his small shop (see the photo). The surround offers support for large panels, as well as provides an ample work surface near the saw.