If you choose to hire a draftsperson or architect, they may charge you based on the square footage of the area you are proposing, by an hourly rate for their time or as a percentage of the cost of the structure. Costs of building permits will be a percentage of the estimated cost of the structure you are proposing (e.g., $15 permit fee per $1000 or 1.5 percent), or a cost-per-square foot depending on your municipality (e.g., $1.20 per square foot). Design work and permits will both differ depending on the part of the country in which you will be building, so ask the questions as you move ahead. One of the costs that is often overlooked in planning is the increase in annual property tax you will pay once your improved property has been reassessed.
In my shop I use a large number of Jorgenson F-clamps. I use many of the small clamps, the most useful being the 12" version. Large F-clamps are essential for cinching down parts on bending forms. I also like aluminum bar clamps because they are much lighter than steel clamps, and therefore less likely to damage a carcase should you bang into the wood during a glue-up.
If you live where summers get hot and humid, you may need more than a fan to keep cool in your workshop. Fortunately, air conditioners will both dehumidify and cool your space — and you don’t need a traditional window to get the job done. Instead of a residential window unit, consider a freestanding portable air conditioner that you can use as needed on hot days.
Personally, I think it sucks to have to lug massive pieces of rough lumber and 4′ x 8′ plywood sheets all the way across a shop. Much respect to basement dwellers who have little choice in the matter. But for those with garage shops, you should think about storing your sheetgoods and solid stock near an entrance. This way when you come home from the lumber dealer, you can back up your vehicle and quickly load the stock into the shop.
Commonly used woodworking tools included axes, adzes, chisels, pull saws, and bow drills. Mortise and tenon joints are attested from the earliest Predynastic period. These joints were strengthened using pegs, dowels and leather or cord lashings. Animal glue came to be used only in the New Kingdom period. Ancient Egyptians invented the art of veneering and used varnishes for finishing, though the composition of these varnishes is unknown. Although different native acacias were used, as was the wood from the local sycamore and tamarisk trees, deforestation in the Nile valley resulted in the need for the importation of wood, notably cedar, but also Aleppo pine, boxwood and oak, starting from the Second Dynasty.
Position #3 is where you will likely spend most of your time in the shop. The diagonally placed workbench is the heart of this plan. The wall-mounted workspace that surrounds the bench forms an ideal “work triangle” within which each of your most commonly needed tools is only one or two steps away. The band saw can be placed outside of the work triangle because it is used slightly less frequently and often needs a little more space around it for your lumber to move.
If you have a fixed-in-place cutoff saw (a radial-arm, miter saw, or sawbuck, for example), it can, unlike the table saw, be conveniently positioned against a wall. Don’t set it in a corner, however, as you’ll need space on either side of the blade. Figure into your plan a two-foot-deep, three-foot-wide space for the saw itself and tables or other supports flanking the tool. Allow enough space directly in front of the saw for the operator to be able to comfortably line up and operate the saw.
With the right tools and materials, what you build is only limited by your imagination and creativity. So why not have a little fun with the kids and teach them something at the same time? Our woodworker tools and woodworking supplies will help you put together an easy birdhouse, squirrel feeder or butterfly house. The kids will love to use our paint samples to add their creative touch, and will enjoy displaying the finished product in the backyard.
I have a 3 car garage, 1-2 car bay, 1 single bay. I made some simple saddle brackets that hang on the outside of the garage door track (V shaped with the top of the V having a cleat that stabilizes the bracket against the top of the track, stove bolts hold the brackets to the track without interfering with the door). Through the bottom of the brackets are drilled holes to hold 3/4″ EMT metal conduit. This is available in 10 ft lengths which is enough to span the single bay track width. I used cotter pins to hold the conduit in the brackets. Eye bolts that slide over the conduit can then be mounted to a 2 bulb flourescent light fixture and bingo, you have lighting that works with the garage door up or down. I did this for my single bay which is where I have my tablesaw and bench/outfeed table. I centered the light at the tablesaw/outfeed table juncture and it makes for awesome lighting for both surfaces.
A clean well-organized environment is key to staying A clean well-organized environment is key to staying happy. The same goes for your desk. Keep the clutter at bay and organize all of your small essentials with the Dickies Work Gear 57012 Mug Organizer. Designed to fit over most mugs this clever caddy features 8 outer pockets and 6 ... More + Product Details Close
See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products
My planer blasts shavings all over the shop floor. I decided to make my own dust chute from 4-in. PVC sewer pipe (which has thinner walls than regular Schedule 40 pipe) and a couple caps. I cut a slit in the pipe and used a heat gun to soften the plastic. That allowed me to open the slit. (Heating PVC releases fumes; ventilation is critical.) I then drilled holes in the flap and screwed it to the planer housing. Finally, I cut a 2-1/2- in. hole in one of the end caps to accept my shop vacuum hose. Works great! — Luis Arce. Here’s what else you can do with PVC pipe.
One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
Line ’em up — Most other woodshop machines work harmoniously when lined up along the walls, where they are easy to power and connect to dust collection. The amount of space left between these tools depends on the amount of room you have, the size of the stock you work with, and whether or not adjacent tools have tables at the same height. You can always pull a machine away from the wall if additional space is needed. Clearly, these options are not the only possibilities and are contingent upon the mix of machines you have, the shape and size of your shop, and the kind of work you do. The bottom line is if the layout works for you, then that’s the best for your shop (and don’t let anyone tell you any different!).