While many woods can be used for carving, there are some clear favorites, including Aspen, Basswood, Butternut, Black Walnut, and Oak. Because it has almost no grain and is notably soft, Basswood is particularly popular with beginner carvers. It is used in many lower-cost instruments like guitars and electric basses. Aspen is similarly soft, although slightly harder, and readily available and inexpensive. Butternut has a deeper hue than Basswood and Aspen and has a nice grain that is easy to carve, and thus friendly for beginners. It's also suitable for furniture. While more expensive that Basswood, Aspen, and Butternut, Black Walnut is a popular choice for its rich color and grain. Lastly, Oak is a strong, sturdy, and versatile wood for carving with a defined grain. It's also a popular wood for furniture making.
A receptacle or circuit that is overloaded is a hazard, in particular one fused beyond its limits. Power tools, especially heavy-duty saws, require lots of amperage, and you may need to add a circuit or two to serve the increased demand in your workshop space. Some tools require 220-volt service, so you may want to install a special plug and line to power that high-powered table saw.
Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wiring for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to finishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a programmable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.
A landscape designer friend of mine tells a story about the college he went to. During his years there, the university embarked upon an ambitious building plan, adding several large structures around the main quad: a dorm, a chemistry lab, and a couple of others. The look of the place, which had remained unchanged for a century, was suddenly transformed, as glass-and-steel modernist structures were interspersed with the earlier ivy-covered stone Victorian-Gothic.
Shop layout is all about making the best use of space. Place your machines so that you have adequate “safe space” that you need to work around them. The “buffer area” beyond that is the amount of room you need to run large stock though a given machine, keeping in mind that buffer areas can overlap between machines. If you want to get more organized, buy some 1/4-inch squared paper, make scale models of each machine including the safe space around each, and place them on your model shop layout. Remember that buffer areas need to be long enough to put an 8' sheet through a table saw, or a 6' plank through your planer, for instance. I raised my planer, so that I can use the area above my router table to pass long planks through the planer – all it takes is some modelling, and a little shuffling, and you will find the layout that works for you. Each space will have challenges; I had the area under the stairs that was wasted space, so I installed the dust collector there.
The planners did an interesting thing, my friend recalls. Instead of commissioning a hugely expensive study to try to predict the new patterns that would result from the opening of the new buildings, rather than devising an anticipated program and laying out a new scheme, the university’s brain trust decided to let the students and faculty, the lifeblood of the university, shape their own arterial flow.
If you choose to hire a draftsperson or architect, they may charge you based on the square footage of the area you are proposing, by an hourly rate for their time or as a percentage of the cost of the structure. Costs of building permits will be a percentage of the estimated cost of the structure you are proposing (e.g., $15 permit fee per $1000 or 1.5 percent), or a cost-per-square foot depending on your municipality (e.g., $1.20 per square foot). Design work and permits will both differ depending on the part of the country in which you will be building, so ask the questions as you move ahead. One of the costs that is often overlooked in planning is the increase in annual property tax you will pay once your improved property has been reassessed.
This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off serious cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bottom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thickness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop without excessive grunting, so that made it very simple to install. The planer has a significant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.
I use binder clips for a lot of things around the shop, and here’s one that I thought I’d share. When I need to make multiple cuts all the same length, I just clamp my jumbo binder clip to my fence and use a 1/4-in.-thick wood scrap pinched in the clip as a stop. Works like a charm! When it’s not in use, I clamp it to the cord so it’s always nearby. — John Muchow
A little different from the others, the Wood Shop is geared more towards the “self-helper.” Take the three-hour safety class, available every Saturday, to earn your qualification card. You can then utilize the shop to work on your own projects. A wonderful variety of wood working equipment is available for customer usage for a very reasonable fee. Be sure to check out the available classes where you can learn to make pens, boxes, decorative cutting boards and even rocking chairs. We also produce custom order items to include coin holders, specialized plaques and shadow boxes.
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
For all of my planning, I must admit there simply was no room in my shop for some tools. I struggled to find a place for my wide jointer and eventually decided against shoehorning it in, instead making a fixture for my router table that joints edges quite well. My scrollsaw, the bulk of my wood supply, and some storage cabinets didn’t make the cut either. These remain in a nearby room.
Use the corners — Some machines are perfectly content to live in a corner, including the bandsaw, scrollsaw, disc or combination sander, and lathe (see the illustration). Orienting the lathe’s tailstock end into a corner will leave room for outboard turning. Pulling the bandsaw away from the wall allows the necessary clearance to cut large curved parts, while locating it near a doorway or window permits resawing of long planks.