The number of windows, as well as their sizing and placement, depends on your orientation, view, desire for ventilation, and needs for daylight and solar gain. Orienting more of your windows towards the south side of your shop and placing them high enough that they are shaded by the eaves in summer, but allow lower-angle winter light to come in, will increase your ability to get free light and heat from the sun. If your goal is to take advantage of passive solar opportunities, make sure that you carefully research the type of glass that is in your windows and look for something with a high solar heat gain coefficient. Higher windows generally allow for benches and tools beneath them, and relatively windowless north walls may be a place to arrange wood storage or mechanicals.
With strength, sturdiness, and durability, maple is a common material for furniture for the bedroom and even china cabinets. Maple is moisture-resistant and frequently displays stand-out swirls in the wood grain, an aesthetically pleasing differentiator from other hardwoods. While most commonly a lighter color, maple also can take stains and paint well.
Let’s face it, one of the most significant costs of your shop will be its foundation. While you’re at it, what about adding space above your shop? There may be regulations preventing you from building living space above your shop if it is in an urban setting or in an outbuilding, but there may be some flexibility depending on where you live. It is in the municipality’s interests to encourage infill housing that uses existing infrastructure. At a minimum, think about including attic trusses to create some space above your shop for drying lumber or storing equipment. Access could be from simple pull-down attic stairs or from the exterior if you don’t want to lose floor space to a stair or ladder. If you’re creating an addition to your house, you may be able to add a couple of rooms you’ve always wanted, such as a family room, office or in-law suite.
One of the misconceptions about planers is that they make lumber straight. They do some straightening, but they don’t make lumber straight. That is what jointers do. Many lumber mills just send rough lumber through the planer allowing the board to exit the machine with the same ups and downs and whoops that is entered with, only now to a consistent thickness. This is especially apparent when gluing up a couple of these roller coaster type of boards and trying to get them to line up. After a couple of those glue-ups, you will swear by lumber that has seen the jointer before the planer, and never skip the jointer.
After a permit has been issued, the building inspector will want to be notified at various points during your build in order to do a site visit, walk around and inspect the details to make sure that they meet code requirements. These inspections are commonly at the point where excavation work is complete, when the foundation is completed but before back-filling, when framing and all structural work has been done, after the installation of the insulation and vapour barrier, and then a final inspection after everything is complete. You may need to have a separate plumbing inspector if you’re adding or changing plumbing fixtures, and electrical work will need to be inspected by the appropriate electrical inspector (in Ontario, the Electrical Safety Authority). In my experience, inspectors appreciate good work, a clean, safe site, and are willing to work with homeowners and builders to make sure that the work will meet code and will endure.
Finally, properly preparing your wood surface is super important. It will make a huge difference when it comes times to stain, paint, or finish your wood. There are a lot of tips for wood surface preparation, but sanding the wood is one of the most important steps. And I find it really helpful to do the bulk of my sanding before I start ripping (cutting) and building with my wood since it’s still in whole pieces. You can check out my simple tips for how to sand wood in my how to stain wood tutorial, which is also good to reference if you need to learn how to stain too!
My hand tools are stored in a cabinet built into my bench but my shop supplies, air tools, and a plethora of “misc stuff” is in a cabinet on the other side of the shop, and my clamps are mounted on a wall adjacent to my bench, where conventional wisdom says tools should be. I just like it that way. I run my DC overhead and drop down… because my floor is on a slab. My bandsaw is mobile so I can pull it out of a semi-alcove for resawing, otherwise it stays in place for small operations (20″ bandsaws are cumbersome to move, even on leveling casters).
Rockler Buffalo is proudly hosting the CNC Users Group! The club consists of CNC owners, users and prospective buyers. Every meeting consists of a ‘Show-n-Tell’ portion, demonstration and then a group discussion. We’d be happy to have you join us and we’ll be looking forward to seeing you at the store! Don’t miss out on this one of kind experience.
Minor variances are applications to your municipality to suspend a particular by-law to allow your project to proceed, based on common sense or precedents set by other buildings in your area. If your municipal committee of adjustment denies permission because a neighbour voices concern over the development, you would have to appeal the decision to the municipal board of your particular province. In that case, you may be better off looking for another piece of property with an existing structure that you could renovate, more relaxed zoning regulations, a larger lot, or more congenial neighbours.
Plan to invest in a set of bench chisels, both standard and low-angle block planes, a No. 4 or 4-1⁄2 smoothing plane, and a No. 6 jack or No. 7 jointer. Between them, these planes will true edges, flatten glue-ups that are wider than your thickness planer, and tame tricky grain that would tear out with a mechanized planer. They also do fine trimming better than any other tools.
If you work with rough lumber, a planer will be absolutely necessary, except for the most rustic of projects. Every piece of rough cut lumber ends up somewhat not straight, not flat and not consistent in thickness, either from variations during the sawing or from stresses which occur while the wood dries. The planer, combined with the jointer, is a one-two punch to remove these variations and produce straight, flat and consistently thick lumber. The reason the planer is ahead of the jointer on this list is that some lumber is straight enough and flat enough to plane without jointing if the job is a little less finicky, thereby skipping the jointer.
Timely article indeed. I’ve been playing with the shop layout tool on Grizzly’s website (http://www.grizzly.com/workshopplanner) which helps you see how tools fit in a specific shop size. However, your insight and experience really helps with ergonomic considerations. When I first built my shop, the first thing I did was installing a wall mounted work bench – as my fore fathers had all done – Big Mistake! Soon-to-be project: ripping it out and building a mobile work bench on wheels (like the one you have pictured).
A kind’a unrelated question. I just finished building the lumber storage rack/sheet goods cart from your “racking my brain..” video. I see you went with the metal wall storage rack in your new shop (which I would love also, just can’t afford) but, I was curious why you didnt put another sheet goods cart. Previously I had the stand up sheet goods storage box like I see your current pictures but, from what little I have used the cart, I like it better than the stand up storage. Its easier to get things in and out and see what all I have. The only draw back is that I can’t store as much on the cart as I could with the box storage.
I have a 3 car garage, 1-2 car bay, 1 single bay. I made some simple saddle brackets that hang on the outside of the garage door track (V shaped with the top of the V having a cleat that stabilizes the bracket against the top of the track, stove bolts hold the brackets to the track without interfering with the door). Through the bottom of the brackets are drilled holes to hold 3/4″ EMT metal conduit. This is available in 10 ft lengths which is enough to span the single bay track width. I used cotter pins to hold the conduit in the brackets. Eye bolts that slide over the conduit can then be mounted to a 2 bulb flourescent light fixture and bingo, you have lighting that works with the garage door up or down. I did this for my single bay which is where I have my tablesaw and bench/outfeed table. I centered the light at the tablesaw/outfeed table juncture and it makes for awesome lighting for both surfaces.
Shops can range from functional spaces adorned with unpainted wallboard to beautifully finished, painted, and trimmed-out spaces. Ultimately, I think it depends on your budget and how important your surroundings are to your mindset as you’re working, or to your clients’ if they will be viewing your shop. If finishing your shop will improve the quality of the work that you will produce, thereby relaxing or inspiring you, or showcase for your clients the quality of the work of which you are capable, it may be a worthwhile investment. A more finished space may also allow for activities like parties or even a weekly poker game (as long as drinks stay off the tools).
If you choose to hire a draftsperson or architect, they may charge you based on the square footage of the area you are proposing, by an hourly rate for their time or as a percentage of the cost of the structure. Costs of building permits will be a percentage of the estimated cost of the structure you are proposing (e.g., $15 permit fee per $1000 or 1.5 percent), or a cost-per-square foot depending on your municipality (e.g., $1.20 per square foot). Design work and permits will both differ depending on the part of the country in which you will be building, so ask the questions as you move ahead. One of the costs that is often overlooked in planning is the increase in annual property tax you will pay once your improved property has been reassessed.
If your shop will be attached to your house or another structure, it will likely need to match its foundation, tying the two structures together so that one does not structurally stress the other if they shift differently. That may dictate a poured concrete or concrete block foundation. Regardless of your foundation type, a cold concrete floor will sap energy away from the rest of the structure if you are not careful, so think about how to insulate it well before you build.
Marc, would not assumptions for a Festool shop differ considerably? Far fewer big machines, and more carrying lightweight precision machines to the wood, for example. I only have a few Festool machines so far (took quite a while to get past the sticker shock), but I am beginning to see how it could change the way we work. My 400 sq ft shop is getting awfully crowded with floor-standing machines and implementing your guidelines, sound as they are, is difficult.
When customers visit my shop we usually start by talking about their wood needs. If it is someone’s first time to visit I also try to get to know them, what they are looking for and what they are expecting from me. Half of them are just looking for rough cut wood, while the others are looking for wood that is processed a little bit more, perhaps jointed or planed, or even sanded. During our time together I get to understand their needs and abilities, and our discussion usually turns to the tools they have in their shop.
Figure out a simple setup for your woodworking space. You don’t need a fancy and expensive workshop or garage to start woodworking. In fact, we’ve never had a workshop or garage (though I do dream of having one haha). In our current town home, we always setup a temporary workshop table in our backyard with a pair of sawhorses and a plywood board from the home improvement store.
Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.
Along with stone, clay and animal parts, wood was one of the first materials worked by early humans. Microwear analysis of the Mousterian stone tools used by the Neanderthals show that many were used to work wood. The development of civilization was closely tied to the development of increasingly greater degrees of skill in working these materials.
See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products
While many woods can be used for carving, there are some clear favorites, including Aspen, Basswood, Butternut, Black Walnut, and Oak. Because it has almost no grain and is notably soft, Basswood is particularly popular with beginner carvers. It is used in many lower-cost instruments like guitars and electric basses. Aspen is similarly soft, although slightly harder, and readily available and inexpensive. Butternut has a deeper hue than Basswood and Aspen and has a nice grain that is easy to carve, and thus friendly for beginners. It's also suitable for furniture. While more expensive that Basswood, Aspen, and Butternut, Black Walnut is a popular choice for its rich color and grain. Lastly, Oak is a strong, sturdy, and versatile wood for carving with a defined grain. It's also a popular wood for furniture making.
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.