There are benefits to either approach. Sharing a common wall with your house can require some careful soundproofing but can reduce heat loss and exterior fin­ishing costs like siding. A shop located in an addition is more likely to be allowed to have living space or storage space above it, and it may be easier to make use of the existing plumbing and electri­cal and heating systems of your home to service your shop space. Another advantage of an addition is not having to run to an outbuilding in minus-30-degree weather or a summer downpour.
Spray gun: Not every woodworking job gets a film finish, but most of mine do. And of those, everyone will meet a spray gun. For a million reasons, including making finishing fast and fun, I recommend using a spray gun whenever possible. It will raise your game and make you n0t hate finishing. (Click here to read my thoughts on purchasing a spray gun).
In many workshops, band saws and drill presses are not used constantly, so they can be set back out of the way. Jointers and shapers can also sometimes be set back out of the midway, but keep in mind that the more trouble they are to reposition, the less useful they’ll be. Remember, too, that while jointers and shapers take up relatively little floor space, you need to allow space on either side that is at least the length of your longest workpiece: a four-foot workpiece needs about a ten-foot space (the tool, plus four feet on either side). The longer the pieces to be joined or shaped, the greater the space required on either side.
Cutting a miter joint that closes up perfectly and maintains a 90 degree angle is really satisfying. Unfortunately, it doesn’t always happen. Here’s a quick fix for a slightly open miter joint; rub the shank of a screwdriver along the miter at a steep angle, from both sides of the joint. Chances are, you’ll be the only one that knows it wasn’t perfect to begin with! Try this amazing miter project!
With the advances in modern technology and the demands of industry, woodwork as a field has changed. The development of Computer Numeric Controlled (CNC) Machines, for example, has made us able to mass-produce and reproduce products faster, with less waste, and often more complex in design than ever before. CNC Routers can carve complicated and highly detailed shapes into flat stock, to create signs or art. Rechargeable power tools speed up creation of many projects and require much less body strength than in the past, for example when boring multiple holes. Skilled fine woodworking, however, remains a craft pursued by many. There remains demand for hand crafted work such as furniture and arts, however with rate and cost of production, the cost for consumers is much higher.
With strength, sturdiness, and durability, maple is a common material for furniture for the bedroom and even china cabinets. Maple is moisture-resistant and frequently displays stand-out swirls in the wood grain, an aesthetically pleasing differentiator from other hardwoods. While most commonly a lighter color, maple also can take stains and paint well.[13]
Sanding concave molding doesn’t have to be difficult. Find a deep socket that fits the contour of your molding. Wrap a piece of sand- paper around the socket and hold it in place with your fingers. Your sanding will be uniform and the delicate edges of the molding won’t round over. — Eric and Cheryl Weltlich. In this video, Travis talks about his favorite sanding tips.
These are all good tips, and apply to pretty much every shop. Like all things woodworking they need to be tweaked so that it’s right for the individual. For instance, I have a basement shop that’s not tiny but it is still space constrained, so worrying about the optimal layout for my ts/jointer/planer is a little off the mark since I don’t have to walk very far; instead, I want to be sure that related tools can be used *at the same time*. Having to move the planer out of the away so that I can use my TS is crazy if it can be avoided. However, interference between my drill press and my planer is less of an issue because they usually don’t get used at the same phase of a project.
With strength, sturdiness, and durability, maple is a common material for furniture for the bedroom and even china cabinets. Maple is moisture-resistant and frequently displays stand-out swirls in the wood grain, an aesthetically pleasing differentiator from other hardwoods. While most commonly a lighter color, maple also can take stains and paint well.[13]
The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ...  More + Product Details Close
Is your cellar damp? If so, you may have to correct that problem before installing your tools and lumber supplies. Insulate pipes to prevent condensation. Make sure your gutters outside keep rainwater running away from the house. Cracks in the cement floor or walls should be filled with hydraulic cement; a high water table may necessitate a sump pump to collect water at a low point and pump it out. Any or all of these circumstances may also require a dehumidifier. In any case, dampness is unacceptable where power tools are to be used because of the risk of electric shock.

Here’s a nifty tip—with a nifty tip—from faithful reader Don Ayers: Fill snap-capped sports water bottles with glue and stick them upside down in a hunk of 2×6. Now you don’t have to wait for the glue to run into the neck of the bottle, and the cap will control glue flow (and never get lost!). To holster the glue dispensers, cut holes in the base with a spade bit that’s a smidgen larger than the cap’s diameter.
Just as a shed or garage can get stifling in the summer heat, winter cold can also make working conditions difficult — if not impossible. To prevent clumsy, stuff fingers from ruining your projects, you need a way to heat your workshop in even the most extremely frigid days of the year. A traditional residential space heater probably won’t cut it, as these are designed to heat single rooms. For a two-car garage or full basement, you’ll need something much bigger.
A little different from the others, the Wood Shop is geared more towards the “self-helper.” Take the three-hour safety class, available every Saturday, to earn your qualification card. You can then utilize the shop to work on your own projects. A wonderful variety of wood working equipment is available for customer usage for a very reasonable fee. Be sure to check out the available classes where you can learn to make pens, boxes, decorative cutting boards and even rocking chairs. We also produce custom order items to include coin holders, specialized plaques and shadow boxes.
Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.

You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.

Gone are the days when you could apply for a building permit based on a sketch on the back of a cigarette pack­age. In provinces like Ontario, design work must be undertaken by an insured designer registered under the provin­cial building code or by the owner of the property. You can do the drawings as the owner if you can demonstrate effec­tively through your drawings that your structure will comply with the techni­cal requirements of the building code in a clear and concise way. You will be required to submit detailed drawings, including the following:


Tired of waiting for finish to dry on one side before finishing the other side? You can purchase standoffs, but it’s also really easy to make them yourself. Simply drive 2-in. drywall screws through 2-in. x 2-in. squares of 3/4-in. thick stock. The screw points will leave a divot in the finish that can be touched up later, but I always let the back side of my project rest on the screws while the finish dries. — Matt Boley. Plus: Check out these 32 other handy hints for frugal shop rats.
I do not rip on the table saw as a rule, to prevent kick back that periodically occurs when natural wood pinches the blade, turning the wood into a missile. I bought a fairly powerful saw, so this is one place where a lighter saw would be adequate. Essentially, I use the table saw for ripping sheet goods, cutting dados, tenons, and cutting small parts to length – all of which can be done with a 1.5 HP saw. I ended up with a King 3 HP, three-belt drive, 10" table saw. The castings are true, and the King Tru-rip fence reminds me of the Biesmeyer fence used on the Canadian General saws. The model is KC-11FX, and it can be purchased for less than half of the price of other, simi­lar saws. On this purchase, I went with the suggestion of Jeff at Brettwood Machinery – he was right; a very good value saw that runs smooth, and has a decent fence.
Because workshops are rough and tumble places, the right fan for the job will have an industrial-strength motor and adjustable fan speeds. Easy-to-clean metal blades and a fully encased motor housing are also important features, especially if your shop tends to fill up with sawdust, wood chips and other fine debris. That extra layer of protection will help the fan motor last for years instead of being damaged by particulates.
×