For the next step up in convenience, consider adding a dedicated beverage cooler to your workshop as well. Though many people set up an old refrigerator in the garage for extra soda and beer, a dedicated mini-fridge will help you save on electricity, since new models are far more efficient than old ones. You can pack your beverage cooler with your favorite soft drinks for a pick-me-up while you work or use it to store a lunch to enjoy on a break —all without tracking dirt and or grease into your clean kitchen.
Other important power tools—A good jigsaw will help get you through many tasks, particularly cutting curves, that would otherwise require a bandsaw. Look for one with blade guides that keep blade deflection to a minimum. A handheld drill is also essential. A quality corded drill is much less expensive than a cordless one, and will never leave you without a charge. Also look for a quality random-orbit sander with a provision for dust collection.
Second, learning how to read lumber dimensions, like knowing what 1×2 or 2×12 actually means, is really important. Understanding softwood lumber dimensions will help you to read woodworking build plans, shop for lumber, and understand the general measurements for your projects. I’ve provided a simple explanation to lumber sizes along with a free lumber size chart printable here!
I have a 3 car garage, 1-2 car bay, 1 single bay. I made some simple saddle brackets that hang on the outside of the garage door track (V shaped with the top of the V having a cleat that stabilizes the bracket against the top of the track, stove bolts hold the brackets to the track without interfering with the door). Through the bottom of the brackets are drilled holes to hold 3/4″ EMT metal conduit. This is available in 10 ft lengths which is enough to span the single bay track width. I used cotter pins to hold the conduit in the brackets. Eye bolts that slide over the conduit can then be mounted to a 2 bulb flourescent light fixture and bingo, you have lighting that works with the garage door up or down. I did this for my single bay which is where I have my tablesaw and bench/outfeed table. I centered the light at the tablesaw/outfeed table juncture and it makes for awesome lighting for both surfaces.
High-velocity fans are also an important tool in their own right, particularly at your finishing station. Increased air flow will help dissipate fumes from paints and sprays for your safety, and you can train a fan on your project to help paint dry more quickly between coats on humid days. To get the most out of your fan, look for floor fans that are easy to aim or wall-mounted fans that will save space in smaller shops.
The planners did an interesting thing, my friend recalls. Instead of commissioning a hugely expensive study to try to predict the new patterns that would result from the opening of the new buildings, rather than devising an anticipated program and laying out a new scheme, the university’s brain trust decided to let the students and faculty, the lifeblood of the university, shape their own arterial flow.
Sanding concave molding doesn’t have to be difficult. Find a deep socket that fits the contour of your molding. Wrap a piece of sand- paper around the socket and hold it in place with your fingers. Your sanding will be uniform and the delicate edges of the molding won’t round over. — Eric and Cheryl Weltlich. In this video, Travis talks about his favorite sanding tips.
Finally, think about the overall color and feel of your workshop. A fresh coat of bright white paint will help your lighting go farther, but you might also consider adding a splash of color for fun. An accent wall or an epoxy floor coating are good ways to upgrade your workshop from drab to fab without adding fussy decorations that will get in the way of business.
My hand tools are stored in a cabinet built into my bench but my shop supplies, air tools, and a plethora of “misc stuff” is in a cabinet on the other side of the shop, and my clamps are mounted on a wall adjacent to my bench, where conventional wisdom says tools should be. I just like it that way. I run my DC overhead and drop down… because my floor is on a slab. My bandsaw is mobile so I can pull it out of a semi-alcove for resawing, otherwise it stays in place for small operations (20″ bandsaws are cumbersome to move, even on leveling casters).
If you choose to hire a draftsperson or architect, they may charge you based on the square footage of the area you are proposing, by an hourly rate for their time or as a percentage of the cost of the structure. Costs of building permits will be a percentage of the estimated cost of the structure you are proposing (e.g., $15 permit fee per $1000 or 1.5 percent), or a cost-per-square foot depending on your municipality (e.g., $1.20 per square foot). Design work and permits will both differ depending on the part of the country in which you will be building, so ask the questions as you move ahead. One of the costs that is often overlooked in planning is the increase in annual property tax you will pay once your improved property has been reassessed.
As the comic George Carlin might say, a shop is mostly just “a place to put your stuff.” The physical aspect of a shop is indeed simply a space of some kind — a garage, a barn, a teepee — that keeps the rain, rust, and robbers away and houses a collection of implements needed to saw, plane, slice, sand, and pound raw wood into useful objects. But just like the difference between a house and a home, what transforms a building full of tools into a comfortable workshop goes beyond the mere physical aspect.