Simply soak a washcloth in water and ring it out a bit so it’s not sopping wet. Put the damp washcloth on the affected area. The water will wick through the wood, and that’s fine. Now, with your iron on its highest setting, place it on the damp washcloth over the affected area, and make small movements back and forth and in circles. Press down firmly and continue until your wash cloth is dry. It won’t take long to evaporate. At this point, the wood fibers are absorbing the water and should expand back to where they were originally. Continue this process and repeat by adding more water until the dents rise up to be flush with the rest of the material.

Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.


Plan to invest in a set of bench chisels, both standard and low-angle block planes, a No. 4 or 4-1⁄2 smoothing plane, and a No. 6 jack or No. 7 jointer. Between them, these planes will true edges, flatten glue-ups that are wider than your thickness planer, and tame tricky grain that would tear out with a mechanized planer. They also do fine trimming better than any other tools.
This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off seri­ous cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bot­tom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thick­ness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop with­out excessive grunting, so that made it very simple to install. The planer has a sig­nificant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.
If your shop lacks wall space or doesn’t have a long enough wall to accommodate long stock, another option is to place the crosscut saw near an operable doorway with the right-hand side closest to the door (see option 2 in the illustration). This leaves most of the length of the fence to the left of the blade (preferable if you’re right-handed), allowing short and mid-sized parts to be cut to length or trimmed without having to open the door.
The number of windows, as well as their sizing and placement, depends on your orientation, view, desire for ventilation, and needs for daylight and solar gain. Orienting more of your windows towards the south side of your shop and placing them high enough that they are shaded by the eaves in summer, but allow lower-angle winter light to come in, will increase your ability to get free light and heat from the sun. If your goal is to take advantage of passive solar opportunities, make sure that you carefully research the type of glass that is in your windows and look for something with a high solar heat gain coefficient. Higher windows generally allow for benches and tools beneath them, and relatively win­dowless north walls may be a place to arrange wood storage or mechanicals.
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
In addition to keeping your workshop comfortable with climate control add-ons, don’t forget to keep your body in optimal condition as you work. A water cooler tucked away in the corner of your workshop will provide a big quality of life boost and allow you to keep at your projects without having to run to the kitchen for a glass of water every time you feel thirsty.
The rubber cushion on my old palm sander was wearing thin around the edges. Because of its age, I couldn’t find a replacement pad. As I was drinking my beverage with a foam can cover around it, I realized I could cut the foam to fit the sander and glue it on. I peeled off the old pad, cleaned the metal base and attached the foam with contact cement. Works for clamp-on as well as stick-on sanding squares! You can find can covers at discount and convenience stores. — Allen J. Muldoon
Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.

The beauty of a portable A/C unit is that you don’t have to heft it into a window and block off a valuable source of fresh air for keeping paint fumes at bay. Instead, choose a model with a low profile that you can tuck under a table or against a wall when not in use — a model with casters for maximum maneuverability is ideal. Choose a high-powered unit that will condition at least 400 square feet of space and move it where you need it for maximum comfort as you work.
This will be a personal matter, depend­ing on whether it will be helpful for finishing or sharpening. However, it is a good idea to look beyond your current use of this space to the next owner. Would it be beneficial to add plumbing hookups so that the shop could someday be an apart­ment, or an art studio, or an extension to your house? It could add to the resale value of your house to be able to create as flexible an area as possible by roughing in a bathroom and even a kitchenette area if you can. If this is done when wall cavities are open or before the slab is poured, your forethought could pay dividends but not cost much up front. 
If you choose to hire a draftsperson or architect, they may charge you based on the square footage of the area you are proposing, by an hourly rate for their time or as a percent­age of the cost of the structure. Costs of building permits will be a percentage of the estimated cost of the structure you are proposing (e.g., $15 permit fee per $1000 or 1.5 percent), or a cost-per-square foot depending on your municipality (e.g., $1.20 per square foot). Design work and permits will both dif­fer depending on the part of the country in which you will be building, so ask the questions as you move ahead. One of the costs that is often overlooked in planning is the increase in annual property tax you will pay once your improved property has been reassessed.
Old doors laid across sawhorses make great temporary workbenches, but they take up a lot of space when you’re not using them. Instead of full-size doors, I use bifold doors with hinges so I can fold them up when I’m done working. They’re also easier to haul around in the pickup for on-the-road jobs. — Harry Steele. Here are 12 more simple workbenches you can build.
Along with stone, clay and animal parts, wood was one of the first materials worked by early humans. Microwear analysis of the Mousterian stone tools used by the Neanderthals show that many were used to work wood. The development of civilization was closely tied to the development of increasingly greater degrees of skill in working these materials.

The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ...  More + Product Details Close
This site uses affiliate links. Given this, please assume that any links leading you to products or services are affiliate links that we will receive compensation from. However, there are millions of products and services on the web, and I only promote those products or services that I would use personally. The Wood Whisperer abides by word of mouth marketing standards and holds integrity in the highest regard. Should I ever be compensated to write, I will make full disclosure. I always give honest opinions, findings, and experiences on products. The views and opinions expressed on this blog are purely our own. Any product claim, statistic, quote or other representation about a product or service should be verified with the manufacturer, provider or party in question. All content on The Wood Whisperer is copyrighted, and may not be reprinted in full form without my written consent.
Sanding the inside of a hole or curved surface can be difficult. To simplify that task, insert a 1/4 x 3-in. bolt into the pilot hole of a hole-saw cutout. Secure the bolt with a washer and nut. Using a hacksaw, cut a 1/4-in. deep slot in line with the bolt. Cut a piece of adhesive-backed sandpaper so that you can slide one end into the slot, wrap it around the cutout, and slide the other end back into the slot. Chuck the bolt into a drill, and you now have a homemade drum sander. — E.R. Comstock. How to Sand Wood Faster
Along with stone, clay and animal parts, wood was one of the first materials worked by early humans. Microwear analysis of the Mousterian stone tools used by the Neanderthals show that many were used to work wood. The development of civilization was closely tied to the development of increasingly greater degrees of skill in working these materials.
In the above video James "Jim" Huggett shares a recent tour of his Furniture Making workshop in Earlysville, Virginia, just a few miles from the Wood And Shop Traditional Woodworking School. Jim reached out to me over a year ago, after he learned that my shop & school were just down the road from him. I dropped by his workshop (J.F. Huggett Custom Furniture), and was amazed that such an accomplished and skilled furniture maker

See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products


Among early finds of wooden tools are the worked sticks from Kalambo Falls, Clacton-on-Sea and Lehringen. The spears from Schöningen (Germany) provide some of the first examples of wooden hunting gear. Flint tools were used for carving. Since Neolithic times, carved wooden vessels are known, for example, from the Linear Pottery culture wells at Kückhofen and Eythra.

The rubber cushion on my old palm sander was wearing thin around the edges. Because of its age, I couldn’t find a replacement pad. As I was drinking my beverage with a foam can cover around it, I realized I could cut the foam to fit the sander and glue it on. I peeled off the old pad, cleaned the metal base and attached the foam with contact cement. Works for clamp-on as well as stick-on sanding squares! You can find can covers at discount and convenience stores. — Allen J. Muldoon
I saw in the March 2019 Vol36,No.1 Iss 259. I have 2 Christian people very close to me that could likely be getting married soon . When I saw the unity cross on page one this would be the perfect gift from a parent. I would like to make it but need the plans. I do not need 3,000 or 60,000 plans I just wish to purchase the plans for the unity cross. I am a beginner so I need detail plans. Please send me information on ordering just the unity cross plans and where to purchase giant Sequoia and white oak woods. Thank you in advance for your help. I need the plans and information before April.
Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.
Second, learning how to read lumber dimensions, like knowing what 1×2 or 2×12 actually means, is really important. Understanding softwood lumber dimensions will help you to read woodworking build plans, shop for lumber, and understand the general measurements for your projects. I’ve provided a simple explanation to lumber sizes along with a free lumber size chart printable here!
The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.

There are a few things particleboard is NOT. It’s not medium density fiberboard (MDF)—a material with greater density and weight composed of more uniform particles. It’s NOT oriented strand board (OSB), a material composed of large wood chips and strands that’s structurally equivalent to plywood. It does NOT have great nail or screw holding ability, nor is it all that water resistant; water can quickly cause the material to swell and lose structural integrity. But if you need something flat and cheap for use in a dry place, particleboard will do you proud. Learn how to make a plastic laminate tabletop with a particleboard substrate.
Some types of wood filler can be hard to get off your hands after they dry, especially if you use your fingers to push it into small cracks and holes. When that happens, I reach for fine grit sandpaper and sand it off my fingers. It’s great for removing dried-on polyurethane glue and canned foam from your hands, too. — Chris James. We’ve got great solutions for removing super glue, too.
The table saw is best suited for making rip cuts, which are cuts along the length of the board, but with a crosscutting jig, the table saw can do just as well on crosscuts, which are cuts across the board. I even use the table saw for resawing thick lumber into thinner boards. The bandsaw is usually the tool for resawing, but any lumber under 6″ wide can be resawn on a 10″ table saw by cutting from both sides of the board.
I could write a whole post on wood species as each species has unique characteristics and traits. But, one of the most common types of wood used in DIY projects and furniture building is pine wood (a softwood). Pine is an affordable and readily available option at your local home improvement store and it comes in many sizes. I highly recommend using pine for beginner woodworking projects. Then, as you improve your skill, try working with some different wood species!
The layout of a workshop will be based, in part, on how it will be used — whether for carpentry, fine woodworking, metalwork or other activities. Regardless of category, however, it's important to keep in mind the principles of efficiency and organization. A layout that's clearly thought out in terms of functionality will make all the difference in creating a workspace that offers a pleasant surrounding as well as a space that's conducive to work.

Clamping mitered edges can be a real hassle because they never seems to line up correctly. The easiest way that I’ve found to get around this process is to use painter’s tape as clamps. First set the pieces so that the outer edges are facing up and tape them edge-to-edge. The flip the pieces over so the beveled edges are facing up and glue them together. Complete the process by taping the last two edges together and let sit until completed. The tape removes easily and the glue won’t attach to the tape, making sanding and finishing very simple. Try this tip with this clever project!

Some of the most important decisions in laying out a shop involve the placement of basic machines, such as the table saw and jointer. Deciding where to put them depends in part on the scale of woodworking you do, which determines the clearance area around these machines if you need to handle long stock or large sheet goods. You’ll also want to consider work flow to avoid an excess amount of running around the shop to accomplish tasks, as well as how to power your machines without turning your shop into a snakepit of extension cords.
×