The layout of a workshop will be based, in part, on how it will be used — whether for carpentry, fine woodworking, metalwork or other activities. Regardless of category, however, it's important to keep in mind the principles of efficiency and organization. A layout that's clearly thought out in terms of functionality will make all the difference in creating a workspace that offers a pleasant surrounding as well as a space that's conducive to work.
These are all good tips, and apply to pretty much every shop. Like all things woodworking they need to be tweaked so that it’s right for the individual. For instance, I have a basement shop that’s not tiny but it is still space constrained, so worrying about the optimal layout for my ts/jointer/planer is a little off the mark since I don’t have to walk very far; instead, I want to be sure that related tools can be used *at the same time*. Having to move the planer out of the away so that I can use my TS is crazy if it can be avoided. However, interference between my drill press and my planer is less of an issue because they usually don’t get used at the same phase of a project.
Here’s an easier way to stain or seal chairs, lattice or anything with numerous tight recesses. Pour the stain into a clean, empty spray bottle ($3). Spray the stain onto the project and wipe up the excess with a brush or rag. The sprayer will squirt stain into all those tight, hard-to-reach cracks and joints. — Valrie Schuster. Learn more about staining wood.
Boat building Bow and arrow Bush carpentry Cabinetry Caning Carpentry Certosina Chainsaw carving Chip carving Clogs Ébéniste Fretwork Intarsia Japanese carpentry Khatam Kohlrosing Log building Marquetry Millwork Parquetry Pyrography Relief carving Root carving Sawdust Segmented turning Shingle weaving Shipbuilding Spindle turning Timber framing Treen Whittling Wood carving Woodturning Wood flour
One of the misconceptions about planers is that they make lumber straight. They do some straightening, but they don’t make lumber straight. That is what jointers do. Many lumber mills just send rough lumber through the planer allowing the board to exit the machine with the same ups and downs and whoops that is entered with, only now to a consistent thickness. This is especially apparent when gluing up a couple of these roller coaster type of boards and trying to get them to line up. After a couple of those glue-ups, you will swear by lumber that has seen the jointer before the planer, and never skip the jointer.
Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.
Hand tools offer your best chance of finding a real bargain. Until the early 20th century, nearly all woodworking was done with hand tools, and their designs and uses have changed little. Most of the high-end planes on today’s market, for example, are just reproductions of the original designs. And because the originals were mass-produced, they are fairly easy to find at rummage sales and antiques stores. (For more information, refer to Matthew Teague’s article, “Buying Old Tools,” in FWW #180).
Use whatever image hosting service you like and post the link to /r/woodworking. The key here is it needs to be apparent that you've built the entry, and you follow the photo requirements listed in the contest rules. Submissions of finished photos only will not be accepted for entry. <-- I can't emphasize this enough, you absolutely need more than 2-3 photos for a valid submission. I will no longer accept entries that have albums that go from rough stock to 90% complete in one jump.
See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products
Because workshops are rough and tumble places, the right fan for the job will have an industrial-strength motor and adjustable fan speeds. Easy-to-clean metal blades and a fully encased motor housing are also important features, especially if your shop tends to fill up with sawdust, wood chips and other fine debris. That extra layer of protection will help the fan motor last for years instead of being damaged by particulates.
Each entry must feature some kind of inlay. This can be wood, glass, metal, etc. Epoxy pours are not allowed per /u/kevin0611's request. An epoxy pour does not count as an inlay for the sake of this contest. (Example would be cutting a pattern on CNC or by hand then filling with a colored epoxy to give the illusion that it's inlay.) Bowties, marquetry, and banding are good examples of allowed inlay in this contest.
My contention has always been that you can build a serviceable shop in your home, develop your hand skills, and make fine furniture. In the past year, I had an opportunity to build a shop from the ground up after moving to a new home. I found a house with an unfinished basement, and set to work. In this article, I will discuss everything from layout, to electrical, to equipment selection. I intend to name names with respect to equipment, so that readers will know what I chose. Everyone’s budget will be different, but I think almost everyone will be able to treat this as a starting point, and adjust accordingly, depending on their own budget.
The #1 shop tip is that the space dictates the layout. Every structure and shop location has subtleties to it, only after you dial those in can you end up at the optimum layout, and in addition to that the kind of work you do is going to dictate how you configure your shop. Casework requires more assembly area and space around your tablesaw for sheet goods, while smaller pieces benefit from having more organization around your bench.
In my shop I use a large number of Jorgenson F-clamps. I use many of the small clamps, the most useful being the 12" version. Large F-clamps are essential for cinching down parts on bending forms. I also like aluminum bar clamps because they are much lighter than steel clamps, and therefore less likely to damage a carcase should you bang into the wood during a glue-up.
The frost generated by Canadian winters wreak havoc on structures through their foundations. According to code conventional foundations and footings must rest below the reach of frost on undisturbed soil (in most provinces, this is safely considered to be 4 ft. below ground level or grade), bear directly on bedrock, or be frost-protected. A shallow foundation may be possible in your area in an outbuilding if you can get an engineer to design and stamp plans for insulating the area directly beside your shallow foundation wall so that frost will not form beneath the footing area and cause damage. A slab-on-grade foundation for an outbuilding is another option that will need to be designed by an engineer so that the concrete slab will structurally bear the weight of the shop structure you build above it.
Even if you buy your lumber already planed, you will still encounter many circumstances that require the use of a planer. For example, you might want to build a simple and delicate jewelry box out of small scrap pieces lying around the shop, and you will end up making a small and clunky jewelry box because all of your lumber is 3/4″ thick, and that’s how it is going to stay. That is just the first example. Think about all of the other times that you will pick up a piece of lumber in the shop and it will be the wrong thickness, either just slightly wrong or in an entirely different size category. A planer is a real problem solver and can fix all of that.
Basically, I created a linear outfeed area, which includes the miter-saw station with folding wings, tablesaw with folding outfeed table, and my large router table, all in a line along the 20-ft. wall and set at the same height. The miter-saw station converts easily for use with a mortiser—with workpiece support on both sides—and it also accepts a minilathe. I even planned a location for all of the tools, blades, and jigs used with the tablesaw: on the operator side, for easy access.
This will be a personal matter, depending on whether it will be helpful for finishing or sharpening. However, it is a good idea to look beyond your current use of this space to the next owner. Would it be beneficial to add plumbing hookups so that the shop could someday be an apartment, or an art studio, or an extension to your house? It could add to the resale value of your house to be able to create as flexible an area as possible by roughing in a bathroom and even a kitchenette area if you can. If this is done when wall cavities are open or before the slab is poured, your forethought could pay dividends but not cost much up front.
Just as a shed or garage can get stifling in the summer heat, winter cold can also make working conditions difficult — if not impossible. To prevent clumsy, stuff fingers from ruining your projects, you need a way to heat your workshop in even the most extremely frigid days of the year. A traditional residential space heater probably won’t cut it, as these are designed to heat single rooms. For a two-car garage or full basement, you’ll need something much bigger.
If your shop lacks wall space or doesn’t have a long enough wall to accommodate long stock, another option is to place the crosscut saw near an operable doorway with the right-hand side closest to the door (see option 2 in the illustration). This leaves most of the length of the fence to the left of the blade (preferable if you’re right-handed), allowing short and mid-sized parts to be cut to length or trimmed without having to open the door.