Here’s an easier way to stain or seal chairs, lattice or anything with numerous tight recesses. Pour the stain into a clean, empty spray bottle ($3). Spray the stain onto the project and wipe up the excess with a brush or rag. The sprayer will squirt stain into all those tight, hard-to-reach cracks and joints. — Valrie Schuster. Learn more about staining wood.

Clamping mitered edges can be a real hassle because they never seems to line up correctly. The easiest way that I’ve found to get around this process is to use painter’s tape as clamps. First set the pieces so that the outer edges are facing up and tape them edge-to-edge. The flip the pieces over so the beveled edges are facing up and glue them together. Complete the process by taping the last two edges together and let sit until completed. The tape removes easily and the glue won’t attach to the tape, making sanding and finishing very simple. Try this tip with this clever project!


Since most of your assembly will be done on the assembly table, it just makes sense to have your clamps nearby. If you’re short on wall space, try a rolling clamp cart! If you use your workbench for assembly, keep your clamps near the workbench. Check out these two helpful articles for clamp racks: A Simple Utilitarian Clamp Rack and A Parallel Clamp Rack.

The rubber cushion on my old palm sander was wearing thin around the edges. Because of its age, I couldn’t find a replacement pad. As I was drinking my beverage with a foam can cover around it, I realized I could cut the foam to fit the sander and glue it on. I peeled off the old pad, cleaned the metal base and attached the foam with contact cement. Works for clamp-on as well as stick-on sanding squares! You can find can covers at discount and convenience stores. — Allen J. Muldoon
Cutting thick, rough, warped hardwood can be cumbersome and dangerous. To provide some control over this process, I built a chop-saw station with wings that extend to support long boards. Again, anytime you make something that consumes shop space, make a shelf underneath to gain storage. The chop saw sits in a recess so that the deck of the saw is at the same height as the workstation deck.
Second, learning how to read lumber dimensions, like knowing what 1×2 or 2×12 actually means, is really important. Understanding softwood lumber dimensions will help you to read woodworking build plans, shop for lumber, and understand the general measurements for your projects. I’ve provided a simple explanation to lumber sizes along with a free lumber size chart printable here!
Typically furniture such as tables and chairs is made using solid stock from hardwoods due to its strength and resistance to warping.[10] Additionally, they also have a greater variety of grain patterns and color and take a finish better which allows the woodworker to exercise a great deal of artistic liberty. Hardwoods can be cut more cleanly and leave less residue on sawblades and other woodworking tools.[10] Cabinet/fixture makers employ the use of plywood and other man made panel products. Some furniture, such as the Windsor chair involve green woodworking, shaping with wood while it contains its natural moisture prior to drying.
Table saw: Of all of the tools in the shop, the table saw is the most useful and versatile. It excels at making straight cuts, and with the addition of any of a million jigs, can be made to perform an amazing number of tasks with repeatability and precision. I use the table saw for roughing out smaller parts from larger pieces, all the way through trimming parts to final size. The only limit to the table saw is that the piece needs to be small enough to be pushed through it. Above a certain size, the table saw becomes less useful and even impossible to use as the saw needs to be brought to the piece, instead of the piece being brought to the saw.
YP - The Real Yellow PagesSM - helps you find the right local businesses to meet your specific needs. Search results are sorted by a combination of factors to give you a set of choices in response to your search criteria. These factors are similar to those you might use to determine which business to select from a local Yellow Pages directory, including proximity to where you are searching, expertise in the specific services or products you need, and comprehensive business information to help evaluate a business's suitability for you. “Preferred” listings, or those with featured website buttons, indicate YP advertisers who directly provide information about their businesses to help consumers make more informed buying decisions. YP advertisers receive higher placement in the default ordering of search results and may appear in sponsored listings on the top, side, or bottom of the search results page.
Some types of wood filler can be hard to get off your hands after they dry, especially if you use your fingers to push it into small cracks and holes. When that happens, I reach for fine grit sandpaper and sand it off my fingers. It’s great for removing dried-on polyurethane glue and canned foam from your hands, too. — Chris James. We’ve got great solutions for removing super glue, too.

Here’s a safe and sound way to make long cuts with a circular saw on plywood clamped to a worktable. Cut about 12 in. into the plywood, then twist a piece of duct tape into a bow tie, with up-and-down adhesive faces. Slide it in the saw kerf and press the tape down above and under the plywood. Now as you finish the cut, the trailing end can’t curl down dangerously as you saw. Hats off to Mike Connelly for simplifying this job. Check out how to make this DIY duct tape wallet.
Use whatever image hosting service you like and post the link to /r/woodworking. The key here is it needs to be apparent that you've built the entry, and you follow the photo requirements listed in the contest rules. Submissions of finished photos only will not be accepted for entry. <-- I can't emphasize this enough, you absolutely need more than 2-3 photos for a valid submission. I will no longer accept entries that have albums that go from rough stock to 90% complete in one jump.

If you have to pick up long lengths of wood from the lumberyard, throw a spring clamp in the back of your vehicle. Use the clamp to attach the warning flag to the end of the protruding lumber. The clamp’s easy to slip on and off, and you won’t have to fuss around with staples, nails or string. — Steve Parker. Plus: Learn more about how to transport large items in your truck.
In each case, we shuffled the bench, jointer, table saw, and band saw across to the top of the stairs, and then tied a rope around each to act as a safety while sliding the machines down the strapping on the stairs. Yeah, the table saw hit the wall, and the promise of a good mud and paint job saved my bacon. The rope worked well, and we were able to get everything down the stairs nice and slowly with­out any major issues.

“I do a lot of finish-sanding freehand, without a sandpaper block, so I can smooth edges and get into nooks and crannies. But the finer grits are usually bonded to thinner paper and, at least for me, the paper is too thin and ends up tearing long before the grit wears out. So I apply duct tape to the back of the sandpaper. The sandpaper is still flexible enough to sand a tight radius and it’s far more durable. You can use this super-strong sandpaper like a shoeshine rag.” — Chuck Merchant
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
Softwood is most commonly found in the regions of the world with lower temperatures and is typically less durable, lighter in weight, and more vulnerable to pests and fungal attacks in comparison to hardwoods. They typically have a paler color and a more open grain than hardwoods, which contributes to the tendency of felled softwood to shrink and swell as it dries.[9] Softwoods usually have a lower density, around 25-37lb/cu ft, which can compromise its strength.[9] Density, however, does vary within both softwoods and hardwoods depending on the wood's geographical origin and growth rate. However, the lower density of softwoods also allows it to have a greater strength with lighter weight. In the United States, softwoods are typically cheaper and more readily available and accessible.[9] Most softwoods are suitable for general construction, especially framing, trim, and finish work, and carcassing.[10][9]

Popular and easy to work with, cherry is in high demand for its reddish-brown color and ease of staining and finishing. Cherry likely won’t be at the local home center, but should be at a lumberyard for a somewhat expensive price.[12] This hardwood is a very common material for furniture, and is resistant to normal wear-and-tear, but it is best for indoor pieces.[13]


The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.
Sanding small items is tricky, as they’re hard to clamp in a vise to work on them. So instead of bringing the sandpaper to the workpiece, I bring the workpiece to the sandpaper. I glue sheets of sandpaper to a piece of plywood; 60 and 100-grit on one side and 150 and 220-grit on the other. Spray adhesive works well for this. Since there’s sandpaper on both sides, my sanding board doesn’t slide around on the bench. Check out these small projects!
The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ...  More + Product Details Close
For our customers who are passionate about woodworking, we offer an extensive selection of tools and accessories to help your woodworking projects come to life. Whether you are a professional carpenter, construction manager or simply wish to build a DIY project, you will find everything that you need on our Amazon.com Woodworking page. Our selection ranges from, screwdriver sets to air filtration, band saws, sanders, drill presses, dust collectors, jointers, laminate trimmers, lathes, planers, benchtop, plate joiners, belt sanders, router combo kits, shapers, sharpener, barn door hardware, circular saws, router tables, router bits, planer, tool box, wood glue, nail gun, table saws, hammers and more.

Next come two options for the table saw’s trusty sidekick, the jointer, as well as for the thickness planer. Because it’s usual to work between all three tools when dressing lumber, the first option, shown in the illustration, locates the jointer nearest the saw to the right of its extension table with the planer nearby. As with the table saw, it always makes sense to align these tools with the shop’s long axis.
×