If you have a fixed-in-place cutoff saw (a radial-arm, miter saw, or sawbuck, for example), it can, unlike the table saw, be conveniently positioned against a wall. Don’t set it in a corner, however, as you’ll need space on either side of the blade. Figure into your plan a two-foot-deep, three-foot-wide space for the saw itself and tables or other supports flanking the tool. Allow enough space directly in front of the saw for the operator to be able to comfortably line up and operate the saw.
See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products
WoodAndShop.com recommends products, with links to online stores, some of which are part of affiliate programs. If users make purchases in those stores (e.g. ebay.com and Amazon.com) those affiliate links lead to referral compensation to us. These payments are very helpful to us, and add no additional fees to our users, so we are grateful for anyone who uses the affiliate links. We run our website based on principles of integrity, and don’t recommend any product that we wouldn’t use ourselves. Any product claim about a service or product should be verified with the manufacturer.
My shop consists of a 9×16 storage building, with 3 feet being used for actual storage! I have a table saw, 13″ planer, lathe, sliding mitre saw, home made router table, small compressor, 5′ 4 drawer bench with vice, table top drill press, 6″ jointer, band saw, shop vac, wall mounted hand tool storage, clamp rack, power tool storage, and no room to turn around! But I put out a few nice pieces! Recently built, a 48″ entry table from 100 yr old milled poplar, coffee table from the same re milled red oak barnwood, and a little triangle shaped corner table from the left over red oak, a 7′ x48″ bookcase from old poplar, a small wall mounted poplar book case, and am presently working on a queen sized bed with a mixture of 100 yr old oak and new kiln dried oak, with drawbored pegging using black walnut from a tree from my yard! I’ve also made several mallets that I find useful from my firewood pile using Cherry, ash, hickory and white and red oak. Building anything in 108 sq ft is a challenge, but patience determination, and decent sales will make it work! One good point is that nothing is out of reach! Except maybe the bathroom!
Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.
Table saw: Of all of the tools in the shop, the table saw is the most useful and versatile. It excels at making straight cuts, and with the addition of any of a million jigs, can be made to perform an amazing number of tasks with repeatability and precision. I use the table saw for roughing out smaller parts from larger pieces, all the way through trimming parts to final size. The only limit to the table saw is that the piece needs to be small enough to be pushed through it. Above a certain size, the table saw becomes less useful and even impossible to use as the saw needs to be brought to the piece, instead of the piece being brought to the saw.
Marc, would not assumptions for a Festool shop differ considerably? Far fewer big machines, and more carrying lightweight precision machines to the wood, for example. I only have a few Festool machines so far (took quite a while to get past the sticker shock), but I am beginning to see how it could change the way we work. My 400 sq ft shop is getting awfully crowded with floor-standing machines and implementing your guidelines, sound as they are, is difficult.
With the advances in modern technology and the demands of industry, woodwork as a field has changed. The development of Computer Numeric Controlled (CNC) Machines, for example, has made us able to mass-produce and reproduce products faster, with less waste, and often more complex in design than ever before. CNC Routers can carve complicated and highly detailed shapes into flat stock, to create signs or art. Rechargeable power tools speed up creation of many projects and require much less body strength than in the past, for example when boring multiple holes. Skilled fine woodworking, however, remains a craft pursued by many. There remains demand for hand crafted work such as furniture and arts, however with rate and cost of production, the cost for consumers is much higher.
Position #3 is where you will likely spend most of your time in the shop. The diagonally placed workbench is the heart of this plan. The wall-mounted workspace that surrounds the bench forms an ideal “work triangle” within which each of your most commonly needed tools is only one or two steps away. The band saw can be placed outside of the work triangle because it is used slightly less frequently and often needs a little more space around it for your lumber to move.
The standard option for a shop floor is a concrete slab. You’re probably not going to go to the trouble of creating a basement beneath your shop, although it is possible. The weight of most woodworking machines suggests that a concrete floor is the most solid and durable substrate available. It has the potential to be used as thermal mass to store heat from your heating system or from the sun, but it can be tiring and hard on your body to be standing on concrete all the time. You can add a vapour barrier, 2x4 sleepers and a wooden floor above the concrete to ease the tendency of the floor to strain your feet and back, or you can add anti-fatigue mats in key areas where you’ll be standing for longer periods.
When cutting full sheets with my circular saw, I use plastic shelving units as sawhorses. The height is just right and by using three of them, I can make cuts in any direction and the plywood is fully supported. And because the shelving units are made of plastic, I can cut right into them without worrying that they’ll damage my saw blade. Plastic shelves are available for $20 at home centers. — John Tinger. Check out these tips for making long cuts with a circular saw.
My shop ended up being 23 x 19 feet, for a total of 437 square feet. I put my wood rack in the basement, but outside the walled in shop area. To keep the dust in the shop, a three part strategy was employed. I have a dust collection system, an air filtration system and a shop vacuum for cleaning dust out of machinery. I put up new walls, installed new electrical service, lighting, and two access doors for ease of materials movement. The shop includes two windows so that I can enjoy natural light, and not feel like I am squirreled away in the basement.
There is significant evidence of advanced woodworking in ancient Egypt. Woodworking is depicted in many extant ancient Egyptian drawings, and a considerable amount of ancient Egyptian furniture (such as stools, chairs, tables, beds, chests) has been preserved. Tombs represent a large collection of these artefacts and the inner coffins found in the tombs were also made of wood. The metal used by the Egyptians for woodworking tools was originally copper and eventually, after 2000 BC bronze as ironworking was unknown until much later.
If your shop lacks wall space or doesn’t have a long enough wall to accommodate long stock, another option is to place the crosscut saw near an operable doorway with the right-hand side closest to the door (see option 2 in the illustration). This leaves most of the length of the fence to the left of the blade (preferable if you’re right-handed), allowing short and mid-sized parts to be cut to length or trimmed without having to open the door.