If your shop lacks wall space or doesn’t have a long enough wall to accommodate long stock, another option is to place the crosscut saw near an operable doorway with the right-hand side closest to the door (see option 2 in the illustration). This leaves most of the length of the fence to the left of the blade (preferable if you’re right-handed), allowing short and mid-sized parts to be cut to length or trimmed without having to open the door.
Before you buy a single tool, you need to take a hard look at your workshop space. If your workshop is a freestanding building or empty barn, you can simply measure the perimeter and know that you have the entire square footage at your disposal including the wall space. If your workshop is tucked into the back of a garage or a corner of partially finished basement, you’ll need to plan your furnishings with cars and water heaters in mind.
If you work with rough lumber, a planer will be absolutely necessary, except for the most rustic of projects. Every piece of rough cut lumber ends up somewhat not straight, not flat and not consistent in thickness, either from variations during the sawing or from stresses which occur while the wood dries. The planer, combined with the jointer, is a one-two punch to remove these variations and produce straight, flat and consistently thick lumber. The reason the planer is ahead of the jointer on this list is that some lumber is straight enough and flat enough to plane without jointing if the job is a little less finicky, thereby skipping the jointer.
To experiment with different wood shop layouts, measure your furniture and equipment to sketch onto your plan in different positions. You can also make cutouts of the footprint of your items so you can easily move them around your floor plan to see how best to arrange them. As you do so, don’t forget to leave adequate spacing around tools and tables.
If your shop will be attached to your house or another structure, it will likely need to match its foundation, tying the two structures together so that one does not structurally stress the other if they shift differently. That may dictate a poured concrete or concrete block foundation. Regardless of your foundation type, a cold concrete floor will sap energy away from the rest of the structure if you are not careful, so think about how to insulate it well before you build.
The dream of a dedicated home shop is a common one among woodworkers. Whether you currently borrow shop space, work in your driveway or side yard, or compete for a corner of your basement with Christmas decorations or your furnace, you may be ready to build your own space that will allow you the freedom of more room and time, and will also keep dust, fumes, and noise under control. Every design/build situation will be unique but there are a series of considerations that you will face in the design and construction phases of your project. Let’s walk through the process and discuss the questions that you will need to ask yourself and others as you approach this project.
To make sure you account for any existing obstructions, it’s a good idea to make a measured drawing of your workshop area on graph paper, noting existing furniture, built-ins and large items on the plan as you go. For example, a common one-car garage workshop layout has built-in tool cabinets and shelves around the perimeter where they won’t impede parking, but you may also have to get clever about folding work tables and saw horses that you can set up as needed in the middle of the garage when you’re working on a project (and cars are parked outside).
I am often surprised at what tools woodworkers don’t use or own, especially when they are some of the few that I find essential. Sometimes it’s just the difference between hand tool and power tool guys, but sometimes it’s just from lack of experience or the fact that they haven’t given it too much thought. Most likely they just buy tools as they need them and never really considered what tools would give them the most bang for the buck.
I wanted to have numerous outlets, and have enough electrical service that I did not have to worry about overloading circuits. There was already some lighting, so I simply picked off that line and added additional lights to keep things bright and cozy. I ran a 240V line for the table saw and jointer with a dedicated breaker. For wall outlets, I ran 14-3 wire, and split all the plugs, so that I can run one machine on the upper plug, and another on the lower plug of any outlet.
Radial-arm saws, sliding compound miter saws, and powered miter boxes (chop boxes) used for crosscutting long boards are best located against the longest wall of the shop, as shown in the first option in the illustration. If the saw is to become a stationary machine, it’s typical to mount or build it into a long, narrow support table fitted with a fence.