Instead of using a container to mix a small amount of epoxy, just make a mixing surface on your workbench using painters tape. Simply lay down strips, overlapping the edges so the epoxy doesn’t get on your bench. When you’re done, peel off the tape and throw it away. This mixing surface will work for more than just epoxy, you can use it for wood glue or any other material you need easy access to while working on a project.
You have a few options for planning your shop space: The first is simply to photocopy the two-dimensional models and use them to create a scale layout of your shop floor. You also can go to my Web site (www.yda-online.com/shopmodels.htm) and download two-dimensional images of each tool to be used either on paper or on the computer. As a third alternative, you can download the same modeling program I used, and create three-dimensional plans.
Any serious woodworker knows that square and flat Any serious woodworker knows that square and flat stock is the key to producing fine work so it’s time to skip the hand tools and graduate to the JJ-6HHDX 6 in. long bed jointer. This beast boasts a helical insert cutter head with staggered carbide inserts yet runs quietly and ... More + Product Details Close
Efficiency does not always increase with experience, because as our woodshops grow older, they sometimes become unnecessarily rearranged or cluttered. And if you’re just now setting up your first woodshop, this shop layout should give you a great starting point. Each picture represents one half of a standard two-car garage. Click on the images for a larger view, and if anything is unclear, ask a question in the comments field!
My hand tools are stored in a cabinet built into my bench but my shop supplies, air tools, and a plethora of “misc stuff” is in a cabinet on the other side of the shop, and my clamps are mounted on a wall adjacent to my bench, where conventional wisdom says tools should be. I just like it that way. I run my DC overhead and drop down… because my floor is on a slab. My bandsaw is mobile so I can pull it out of a semi-alcove for resawing, otherwise it stays in place for small operations (20″ bandsaws are cumbersome to move, even on leveling casters).
Finally, properly preparing your wood surface is super important. It will make a huge difference when it comes times to stain, paint, or finish your wood. There are a lot of tips for wood surface preparation, but sanding the wood is one of the most important steps. And I find it really helpful to do the bulk of my sanding before I start ripping (cutting) and building with my wood since it’s still in whole pieces. You can check out my simple tips for how to sand wood in my how to stain wood tutorial, which is also good to reference if you need to learn how to stain too!
In the above video James "Jim" Huggett shares a recent tour of his Furniture Making workshop in Earlysville, Virginia, just a few miles from the Wood And Shop Traditional Woodworking School. Jim reached out to me over a year ago, after he learned that my shop & school were just down the road from him. I dropped by his workshop (J.F. Huggett Custom Furniture), and was amazed that such an accomplished and skilled furniture maker
Here’s a safe and sound way to make long cuts with a circular saw on plywood clamped to a worktable. Cut about 12 in. into the plywood, then twist a piece of duct tape into a bow tie, with up-and-down adhesive faces. Slide it in the saw kerf and press the tape down above and under the plywood. Now as you finish the cut, the trailing end can’t curl down dangerously as you saw. Hats off to Mike Connelly for simplifying this job. Check out how to make this DIY duct tape wallet.
These are all good tips, and apply to pretty much every shop. Like all things woodworking they need to be tweaked so that it’s right for the individual. For instance, I have a basement shop that’s not tiny but it is still space constrained, so worrying about the optimal layout for my ts/jointer/planer is a little off the mark since I don’t have to walk very far; instead, I want to be sure that related tools can be used *at the same time*. Having to move the planer out of the away so that I can use my TS is crazy if it can be avoided. However, interference between my drill press and my planer is less of an issue because they usually don’t get used at the same phase of a project.
If your shop is long and narrow, option 2 provides maximum space to the left of the fence for handling large sheets of plywood. If you often work with full sheets of plywood or other sheet goods, you might want to build the table saw into an extension table surround, as San Diego woodworker Pat Curci did in his small shop (see the photo). The surround offers support for large panels, as well as provides an ample work surface near the saw.