In each case, we shuffled the bench, jointer, table saw, and band saw across to the top of the stairs, and then tied a rope around each to act as a safety while sliding the machines down the strapping on the stairs. Yeah, the table saw hit the wall, and the promise of a good mud and paint job saved my bacon. The rope worked well, and we were able to get everything down the stairs nice and slowly with­out any major issues.
With these three power tools (and a few hand tools), I feel like I could make about 80% of the jobs that come through my shop on a daily basis. Obviously, some jobs will require more specialized power tools to complete, but these three probably find their way into almost all of my work. With that said, there are a few other tools that I couldn’t imagine being without and I feel need to be added to the list.
Some types of wood filler can be hard to get off your hands after they dry, especially if you use your fingers to push it into small cracks and holes. When that happens, I reach for fine grit sandpaper and sand it off my fingers. It’s great for removing dried-on polyurethane glue and canned foam from your hands, too. — Chris James. We’ve got great solutions for removing super glue, too.
Great suggestions for a large workshop where there is floor space… the shop I wish I had!!! My shop is a one car garage 23 X 13, which poses a real problem when it comes to workflow and tool positioning. I use your philosophy in reverse Marc; meaning, all my tools are on casters and I store my tools at one end of the shop in an order that allows me to bring the right tool or two into the centre of the shop to use. Bring the tool to the wood.
Marc, would not assumptions for a Festool shop differ considerably? Far fewer big machines, and more carrying lightweight precision machines to the wood, for example. I only have a few Festool machines so far (took quite a while to get past the sticker shock), but I am beginning to see how it could change the way we work. My 400 sq ft shop is getting awfully crowded with floor-standing machines and implementing your guidelines, sound as they are, is difficult.

Cedars are strong, aromatic softwoods that are capable of enduring outdoor elements, the most common of which is the Western Red Cedar. Western Red Cedar can sustain wet environments without succumbing to rot, and as a result is commonly used for outdoor projects such as patios, outdoor furniture, and building exteriors. This wood can be easily found at most home centers for a moderate price.[12]


Enter the garage heater. These space heaters are specifically designed to warm up wide open areas and to function under much tougher circumstances than you’re likely to find in the average house. A well designed garage heater will offer at least 5,000 watts of heating power — enough to warm 750 square feet of space. A smaller heater might take off a bit of the chill, but to really warm your workshop — and keep it that way — you’ll need a heater of this size.
Always nice to see project ideas. Yet, to make a living while woodworking all projects need to be scaled up so that one can actually earn enough to survive and compete against the flood of Chinese imports and others. Substitute products made from plastic, metal or wood are a common place and normally cheaper due to mass production and human rights violations. Politicians don’t care about the disappearance of many of America’s Cottage Industries and most consumers don’t care as well.
The layout of a workshop will be based, in part, on how it will be used — whether for carpentry, fine woodworking, metalwork or other activities. Regardless of category, however, it's important to keep in mind the principles of efficiency and organization. A layout that's clearly thought out in terms of functionality will make all the difference in creating a workspace that offers a pleasant surrounding as well as a space that's conducive to work.

How do you divide 11-3/8-in. (or any other mathematically difficult number) into equal parts without dividing fractions? Simple. Angle your tape across the workpiece until it reads an easily-divisible dimension and make your marks with the tape angled. For example, say you want to divide an 11-3/8-in. board into three equal parts. Angle the tape until it reads 12-in., and then make marks at “4” and “8”. Plus: More measuring tips and tricks.

After a permit has been issued, the building inspector will want to be notified at various points during your build in order to do a site visit, walk around and inspect the details to make sure that they meet code requirements. These inspections are commonly at the point where excavation work is complete, when the foundation is completed but before back-filling, when framing and all structural work has been done, after the installation of the insulation and vapour barrier, and then a final inspection after everything is complete. You may need to have a separate plumbing inspector if you’re adding or changing plumbing fixtures, and electrical work will need to be inspected by the appro­priate electrical inspector (in Ontario, the Electrical Safety Authority). In my experience, inspectors appreciate good work, a clean, safe site, and are willing to work with hom­eowners and builders to make sure that the work will meet code and will endure.
I added an accessory mitre gauge to the saw for accurate cut-off work. The Incra Miter1000 showed up under the Christmas tree after the Lee Valley flyer photo with part number mysteri­ously ended up on the fridge door with a circle around it last December. A great addition, the Incra is light, accurate, and provides adjustable stops for cutting multiple parts to precise length. I will also make a plywood cut-off sled for the saw for squaring larger panels.

The layout of a workshop will be based, in part, on how it will be used — whether for carpentry, fine woodworking, metalwork or other activities. Regardless of category, however, it's important to keep in mind the principles of efficiency and organization. A layout that's clearly thought out in terms of functionality will make all the difference in creating a workspace that offers a pleasant surrounding as well as a space that's conducive to work.


Finally, think about the overall color and feel of your workshop. A fresh coat of bright white paint will help your lighting go farther, but you might also consider adding a splash of color for fun. An accent wall or an epoxy floor coating are good ways to upgrade your workshop from drab to fab without adding fussy decorations that will get in the way of business.
Enter the garage heater. These space heaters are specifically designed to warm up wide open areas and to function under much tougher circumstances than you’re likely to find in the average house. A well designed garage heater will offer at least 5,000 watts of heating power — enough to warm 750 square feet of space. A smaller heater might take off a bit of the chill, but to really warm your workshop — and keep it that way — you’ll need a heater of this size.

Always nice to see project ideas. Yet, to make a living while woodworking all projects need to be scaled up so that one can actually earn enough to survive and compete against the flood of Chinese imports and others. Substitute products made from plastic, metal or wood are a common place and normally cheaper due to mass production and human rights violations. Politicians don’t care about the disappearance of many of America’s Cottage Industries and most consumers don’t care as well.

Popular and easy to work with, cherry is in high demand for its reddish-brown color and ease of staining and finishing. Cherry likely won’t be at the local home center, but should be at a lumberyard for a somewhat expensive price.[12] This hardwood is a very common material for furniture, and is resistant to normal wear-and-tear, but it is best for indoor pieces.[13]
Clamping mitered edges can be a real hassle because they never seems to line up correctly. The easiest way that I’ve found to get around this process is to use painter’s tape as clamps. First set the pieces so that the outer edges are facing up and tape them edge-to-edge. The flip the pieces over so the beveled edges are facing up and glue them together. Complete the process by taping the last two edges together and let sit until completed. The tape removes easily and the glue won’t attach to the tape, making sanding and finishing very simple. Try this tip with this clever project!

Enter the garage heater. These space heaters are specifically designed to warm up wide open areas and to function under much tougher circumstances than you’re likely to find in the average house. A well designed garage heater will offer at least 5,000 watts of heating power — enough to warm 750 square feet of space. A smaller heater might take off a bit of the chill, but to really warm your workshop — and keep it that way — you’ll need a heater of this size.
A great freestanding beverage cooler should come equipped with a thermostat that lets you control the temperature to your liking — the colder the better for carbonated drinks, which tend to taste best when served at a frosty 34 degrees. If you plan to store adult beverages in your cooler, look for a model with a lock to keep your drinks away from children and teens. You’ll also want a model that allows you to reverse the way the door swings when you set it up, as this will provide flexibility in your workshop layout to help maximize your space.
If your shop will be attached to your house or another struc­ture, it will likely need to match its foundation, tying the two structures together so that one does not structurally stress the other if they shift differently. That may dictate a poured concrete or concrete block foundation. Regardless of your foundation type, a cold concrete floor will sap energy away from the rest of the structure if you are not careful, so think about how to insulate it well before you build.
Basically, I created a linear outfeed area, which includes the miter-saw station with folding wings, tablesaw with folding outfeed table, and my large router table, all in a line along the 20-ft. wall and set at the same height. The miter-saw station converts easily for use with a mortiser—with workpiece support on both sides—and it also accepts a minilathe. I even planned a location for all of the tools, blades, and jigs used with the tablesaw: on the operator side, for easy access.
If you have a fixed-in-place cutoff saw (a radial-arm, miter saw, or sawbuck, for example), it can, unlike the table saw, be conveniently positioned against a wall. Don’t set it in a corner, however, as you’ll need space on either side of the blade. Figure into your plan a two-foot-deep, three-foot-wide space for the saw itself and tables or other supports flanking the tool. Allow enough space directly in front of the saw for the operator to be able to comfortably line up and operate the saw.
Hardwoods, botanically known as angiosperms, are deciduous and shed their leaves annually with temperature changes.[8] Softwoods come from trees botanically known as gymnosperms, which are coniferous, cone-bearing, and stay green year round.[8] Although a general pattern, softwoods are not necessarily always “softer” than hardwoods, and vice versa.[9]
I saw in the March 2019 Vol36,No.1 Iss 259. I have 2 Christian people very close to me that could likely be getting married soon . When I saw the unity cross on page one this would be the perfect gift from a parent. I would like to make it but need the plans. I do not need 3,000 or 60,000 plans I just wish to purchase the plans for the unity cross. I am a beginner so I need detail plans. Please send me information on ordering just the unity cross plans and where to purchase giant Sequoia and white oak woods. Thank you in advance for your help. I need the plans and information before April.
For our customers who are passionate about woodworking, we offer an extensive selection of tools and accessories to help your woodworking projects come to life. Whether you are a professional carpenter, construction manager or simply wish to build a DIY project, you will find everything that you need on our Amazon.com Woodworking page. Our selection ranges from, screwdriver sets to air filtration, band saws, sanders, drill presses, dust collectors, jointers, laminate trimmers, lathes, planers, benchtop, plate joiners, belt sanders, router combo kits, shapers, sharpener, barn door hardware, circular saws, router tables, router bits, planer, tool box, wood glue, nail gun, table saws, hammers and more.

Hey Marc. I’m sure you may have said it somewhere when you were building your fine shop, but, I wanted to know if that gray flooring in your shop is one of those rubber flooring deals. It looks like a small sample I just got in the mail the other day. It is rubber, but, almost feels like plastic, and looked like the same color as your floor. Thnx in advance.
Hi Liz. I am sorry you were having trouble unsubscribing to the newsletter. Your information has been updated. Your email address has been removed from our Woodworkers Guild of America E-Newsletter mailing list. Please allow up to 5 business days for your request to be completed. If you have any questions, please contact our customer service team at 1-855-253-0822.
Much like the assembly table, nearly every project in my shop makes extensive use of the table saw. And like it or not, my outfeed table becomes a second storage area for project parts and cut-offs. So I like to have mine located in the middle of the shop for the same reasons as the assembly table. Additionally, it’s nice to have ample space around the tablesaw for those larger workpieces. Unless it’s absolutely necessary, I’m not a fan of storing the table saw against a wall.
My contention has always been that you can build a serviceable shop in your home, develop your hand skills, and make fine furniture. In the past year, I had an opportunity to build a shop from the ground up after moving to a new home. I found a house with an unfinished basement, and set to work. In this article, I will discuss everything from layout, to electrical, to equipment selection. I intend to name names with respect to equipment, so that readers will know what I chose. Everyone’s budget will be different, but I think almost everyone will be able to treat this as a starting point, and adjust accordingly, depending on their own budget.
Well you can only do so much with your given space. These guidelines are just general best-practices, but that certainly doesn’t mean everyone will be able to execute them to the letter. Even I make concessions for my personal situation. And yes, there would be differences in a Festool shop. I imagine everything would simply revolve around an MFT. :)
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.

Figure out a simple setup for your woodworking space. You don’t need a fancy and expensive workshop or garage to start woodworking. In fact, we’ve never had a workshop or garage (though I do dream of having one haha). In our current town home, we always setup a temporary workshop table in our backyard with a pair of sawhorses and a plywood board from the home improvement store.

Instead of using a container to mix a small amount of epoxy, just make a mixing surface on your workbench using painters tape. Simply lay down strips, overlapping the edges so the epoxy doesn’t get on your bench. When you’re done, peel off the tape and throw it away. This mixing surface will work for more than just epoxy, you can use it for wood glue or any other material you need easy access to while working on a project.


YP - The Real Yellow PagesSM - helps you find the right local businesses to meet your specific needs. Search results are sorted by a combination of factors to give you a set of choices in response to your search criteria. These factors are similar to those you might use to determine which business to select from a local Yellow Pages directory, including proximity to where you are searching, expertise in the specific services or products you need, and comprehensive business information to help evaluate a business's suitability for you. “Preferred” listings, or those with featured website buttons, indicate YP advertisers who directly provide information about their businesses to help consumers make more informed buying decisions. YP advertisers receive higher placement in the default ordering of search results and may appear in sponsored listings on the top, side, or bottom of the search results page.
A shop geared toward woodworking would have lumber storage located at one corner of the triangle. Storage space for wood — both long pieces and flat plywood pieces — should be adequate. Raised storage, such as racks or shelves mounted on the wall, must be sturdy. Wood storage should also be in close proximity to the stationary tools or machines (table saw, jointer, power planer, etc.) to avoid frequently carrying heavy wood across the span of the workspace. Wood storage should be handy and near the area where the heavy woodworking tasks will take place. Keep in mind that a considerable amount of space will be needed around stationary tools such as a table saws and jointers for manipulating large pieces of raw lumber.
When cutting full sheets with my circular saw, I use plastic shelving units as sawhorses. The height is just right and by using three of them, I can make cuts in any direction and the plywood is fully supported. And because the shelving units are made of plastic, I can cut right into them without worrying that they’ll damage my saw blade. Plastic shelves are available for $20 at home centers. — John Tinger. Check out these tips for making long cuts with a circular saw.
Here’s a nifty tip—with a nifty tip—from faithful reader Don Ayers: Fill snap-capped sports water bottles with glue and stick them upside down in a hunk of 2×6. Now you don’t have to wait for the glue to run into the neck of the bottle, and the cap will control glue flow (and never get lost!). To holster the glue dispensers, cut holes in the base with a spade bit that’s a smidgen larger than the cap’s diameter.

Typically furniture such as tables and chairs is made using solid stock from hardwoods due to its strength and resistance to warping.[10] Additionally, they also have a greater variety of grain patterns and color and take a finish better which allows the woodworker to exercise a great deal of artistic liberty. Hardwoods can be cut more cleanly and leave less residue on sawblades and other woodworking tools.[10] Cabinet/fixture makers employ the use of plywood and other man made panel products. Some furniture, such as the Windsor chair involve green woodworking, shaping with wood while it contains its natural moisture prior to drying.
No matter what woodworking or tool-related venture you're taking on, Amazon.com has the trustworthy brands delivering the helpful products you'll want, brands like Dewalt, Makita, Stanley, Black + Decker, Festool, Shop-Vac, Jet and more. You'll also find a wide range of deals and special offers on woodworking products in the Deals and Savings page. Shop on Amazon.com and get free shipping for qualifying orders.
I’m helping my son (who is significantly disabled) get started with a business idea that he had — one that I’d think was brilliant even if I weren’t his Mom — brilliant enough that I’ve “retired” from my law practice and moved us from MO to GA. Having lost 99.9% of ALL of my tools in the move (even the big ticket items, nearly 30 years collection — stolen by the mover!) I am now re-investing in tools, limiting my purchases to what we must have rather than all the fun stuff I used to have. . . .(So sad).
For the next step up in convenience, consider adding a dedicated beverage cooler to your workshop as well. Though many people set up an old refrigerator in the garage for extra soda and beer, a dedicated mini-fridge will help you save on electricity, since new models are far more efficient than old ones. You can pack your beverage cooler with your favorite soft drinks for a pick-me-up while you work or use it to store a lunch to enjoy on a break —all without tracking dirt and or grease into your clean kitchen.
×