A few months ago Dave Heller, a custom furniture maker and Marquetry expert, reached out to me about teaching at the Wood and Shop Traditional Woodworking School. When he brought over some of his fine furniture, I was really impressed. He's truly an artist, and way better than me! (You can see his furniture here on his website and here on his Instagram account). Like many woodworkers, Dave first pursued woodworking as a hobby. He
If your shop will be attached to your house or another structure, it will likely need to match its foundation, tying the two structures together so that one does not structurally stress the other if they shift differently. That may dictate a poured concrete or concrete block foundation. Regardless of your foundation type, a cold concrete floor will sap energy away from the rest of the structure if you are not careful, so think about how to insulate it well before you build.
Other important power tools—A good jigsaw will help get you through many tasks, particularly cutting curves, that would otherwise require a bandsaw. Look for one with blade guides that keep blade deflection to a minimum. A handheld drill is also essential. A quality corded drill is much less expensive than a cordless one, and will never leave you without a charge. Also look for a quality random-orbit sander with a provision for dust collection.
Finally, properly preparing your wood surface is super important. It will make a huge difference when it comes times to stain, paint, or finish your wood. There are a lot of tips for wood surface preparation, but sanding the wood is one of the most important steps. And I find it really helpful to do the bulk of my sanding before I start ripping (cutting) and building with my wood since it’s still in whole pieces. You can check out my simple tips for how to sand wood in my how to stain wood tutorial, which is also good to reference if you need to learn how to stain too!
I have a 3 car garage, 1-2 car bay, 1 single bay. I made some simple saddle brackets that hang on the outside of the garage door track (V shaped with the top of the V having a cleat that stabilizes the bracket against the top of the track, stove bolts hold the brackets to the track without interfering with the door). Through the bottom of the brackets are drilled holes to hold 3/4″ EMT metal conduit. This is available in 10 ft lengths which is enough to span the single bay track width. I used cotter pins to hold the conduit in the brackets. Eye bolts that slide over the conduit can then be mounted to a 2 bulb flourescent light fixture and bingo, you have lighting that works with the garage door up or down. I did this for my single bay which is where I have my tablesaw and bench/outfeed table. I centered the light at the tablesaw/outfeed table juncture and it makes for awesome lighting for both surfaces.
Short scraps of hardwood are too good to throw away but hard to store neatly. So I bought a 4-ft. tube form made for concrete footings, cut it in half (the cardboard-like material cuts easily) and set the tubes on end. I tack the tubes to a wall or a bench leg so they don’t fall over. With the wood scraps stored upright, it’s easy to find a piece just the right length. Tube forms are available in various diameters for $5 and up at home centers. — Bill Wells. Here’s another brilliant use for these concrete forms.
Personally, I think it sucks to have to lug massive pieces of rough lumber and 4′ x 8′ plywood sheets all the way across a shop. Much respect to basement dwellers who have little choice in the matter. But for those with garage shops, you should think about storing your sheetgoods and solid stock near an entrance. This way when you come home from the lumber dealer, you can back up your vehicle and quickly load the stock into the shop.
Depending on your situation, you may need to upgrade to 200 amp electrical service in order to meet the needs of your house and your shop. It may also be in your interests to add in a separate electrical service meter on your shop so that you can clearly write off electrical use for your business, or in future rent the space out and clearly separate out the utilities for billing your tenant. Generally, you don’t want to skimp on the power to your shop or on the lighting you include.
I place the band saw first in my order of purchases, because I consider it the heart of the shop. Band saws are very safe tools for ripping, re-sawing, cutting curves and more because all of the force is downward, virtually eliminating any chance of unexpected kickbacks. I wanted a saw that had a strong back, dynamically balanced cast iron wheels for smooth operation and flywheel effect, 12" depth of cut, good dust extraction design, a large table and a solid fence. After shopping around, I settled on the General International Model 90-170 14" saw. It is very smooth, comes with an Excalibur fence, and it is light enough (133kg) to move into your basement without crushing someone.
A receptacle or circuit that is overloaded is a hazard, in particular one fused beyond its limits. Power tools, especially heavy-duty saws, require lots of amperage, and you may need to add a circuit or two to serve the increased demand in your workshop space. Some tools require 220-volt service, so you may want to install a special plug and line to power that high-powered table saw.
An interesting variation of this layout is displayed in Jim Tolpin’s shop, shown in the photo at right. Tolpin located his jointer to the left of his table saw, its height low enough to allow panels cut on the saw to pass over the jointer. To save space, his portable planer lives beneath the saw. All three tools are oriented toward the garage-style door, which can be opened to allow long boards to be ripped, jointed, or thickness planed.