Depending on your situation, you may need to upgrade to 200 amp electrical service in order to meet the needs of your house and your shop. It may also be in your interests to add in a separate electrical service meter on your shop so that you can clearly write off electrical use for your business, or in future rent the space out and clearly separate out the utilities for billing your tenant. Generally, you don’t want to skimp on the power to your shop or on the lighting you include.
I set an initial budget of $10,000 to build the shop – everything from studs and drywall to hand tools and machinery. The final number was over by $1,000, but I’m still very happy with the result. The shop is now my haven, with a good sound system and good lighting. Every time I go back into the shop, it is exactly the way I left it, because it is my shop!
My advice here is to make a detailed list of what the various parts of the build will be (drawings, permits, foundation, framing, electrical, etc.) and decide what you would like to do yourself and what you will need to hire others to do. Get quotes on the work that you would like to hire out and estimate the materials you will need to do your portion. You may want to factor in your time into the cost as well, especially if you will be passing up other income to work on the project. At some lumberyards, you will be able to give detailed drawings to an estimator on staff who will do a material takeoff list for you of what you’ll need and what it will cost. When all the numbers come in, you can put together a budget and plan for an overrun allowance of around 15 percent. If you keep track of the materials and subcontract costs as you go, you can stay on track and make decisions as you go about the latter stages of the project without regretting it later. If it is challenging to obtain funding for a complete build, you may want to stage the build so that initially the frame goes up and the exterior is finished, and then you finish the interior work as you have time or as funds become available.
Hard to determine which stain you need in that bespattered collection of cans? An easy-to-make “stain index,” courtesy of reader Bob Jacek, solves the problem. Section off boards of your favorite woods into squares with masking tape, and apply the different stains across the width of each wood type (pine, oak, birch, etc.). When the stains are dry, brush on lengthwise your regular ﬁnishes—polyurethane, water-based polyurethane, oil, orange shellac, etc. You’ll be able to tell how each stain looks with each ﬁnish. Label each one. Use both sides of each board, and you’ll have a wooden encyclopedia of stain and ﬁnish combinations. Plus: How to stain wood evenly.
Here’s an easier way to stain or seal chairs, lattice or anything with numerous tight recesses. Pour the stain into a clean, empty spray bottle ($3). Spray the stain onto the project and wipe up the excess with a brush or rag. The sprayer will squirt stain into all those tight, hard-to-reach cracks and joints. — Valrie Schuster. Learn more about staining wood.
Shop layout is all about making the best use of space. Place your machines so that you have adequate “safe space” that you need to work around them. The “buffer area” beyond that is the amount of room you need to run large stock though a given machine, keeping in mind that buffer areas can overlap between machines. If you want to get more organized, buy some 1/4-inch squared paper, make scale models of each machine including the safe space around each, and place them on your model shop layout. Remember that buffer areas need to be long enough to put an 8' sheet through a table saw, or a 6' plank through your planer, for instance. I raised my planer, so that I can use the area above my router table to pass long planks through the planer – all it takes is some modelling, and a little shuffling, and you will find the layout that works for you. Each space will have challenges; I had the area under the stairs that was wasted space, so I installed the dust collector there.
Although refrigerators long ago rendered them obsolete, antique oak ice boxes remain popular with collectors, even though they’re expensive and hard to find. This do-it-yourself version is neither: it’s both inexpensive and easy to build. An authentic reproduction of an original, the project is especially popular when used as a bar, but it has many