Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.
Instead of using a container to mix a small amount of epoxy, just make a mixing surface on your workbench using painters tape. Simply lay down strips, overlapping the edges so the epoxy doesn’t get on your bench. When you’re done, peel off the tape and throw it away. This mixing surface will work for more than just epoxy, you can use it for wood glue or any other material you need easy access to while working on a project.
I set an initial budget of $10,000 to build the shop – everything from studs and drywall to hand tools and machinery. The final number was over by $1,000, but I’m still very happy with the result. The shop is now my haven, with a good sound sys­tem and good lighting. Every time I go back into the shop, it is exactly the way I left it, because it is my shop!
With an orbital sander and good sandpaper you can smooth wood evenly and easily with first-class results. When flush-sanding solid edge-banding, draw a squiggly line across the joint before sanding. The edge-banding will be slightly proud of the plywood veneer, so the pencil marks provide a visual aid to make sure that you’re sanding flat, and that you don’t sand through the plywood’s veneer. As you go, you can also test for a smooth, level transition by gently scraping your fingernails against the transition. If it’s smooth, your fingers will not catch on the seam between the two pieces
Finding affordable lumber has always been a mainstay for woodworkers, and when you tie our dwindling natural resources into the conversation the time is right to look at milling your own lumber. This seven-part weekly video series takes you through how to find lumber, how to operate a sawmill, details on types of sawing methods, stickering and drying and ultimately advice on using a mill as part of a business. Learn what you need to know to understand Milling Your Own Lumber.
Keep in mind, there are no perfect boards, but try to always use the straighter boards and avoid warping boards. Also, Brandon and I have found that when it comes to picking out lumber at Home Depot and Lowes, they tend to stock up on fresh boards a few days before the weekend starts (so Thursday/Friday). And then, on Sundays and Mondays, the boards are usually really picked over and there isn’t a good selection. Just another tip to keep in mind!
This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com.

Although refrigerators long ago rendered them obsolete, antique oak ice boxes remain popular with collectors, even though they’re expensive and hard to find. This do-it-yourself version is neither: it’s both inexpensive and easy to build. An authentic reproduction of an original, the project is especially popular when used as a bar, but it has many


One of the misconceptions about planers is that they make lumber straight. They do some straightening, but they don’t make lumber straight. That is what jointers do. Many lumber mills just send rough lumber through the planer allowing the board to exit the machine with the same ups and downs and whoops that is entered with, only now to a consistent thickness. This is especially apparent when gluing up a couple of these roller coaster type of boards and trying to get them to line up. After a couple of those glue-ups, you will swear by lumber that has seen the jointer before the planer, and never skip the jointer.
I do not rip on the table saw as a rule, to prevent kick back that periodically occurs when natural wood pinches the blade, turning the wood into a missile. I bought a fairly powerful saw, so this is one place where a lighter saw would be adequate. Essentially, I use the table saw for ripping sheet goods, cutting dados, tenons, and cutting small parts to length – all of which can be done with a 1.5 HP saw. I ended up with a King 3 HP, three-belt drive, 10" table saw. The castings are true, and the King Tru-rip fence reminds me of the Biesmeyer fence used on the Canadian General saws. The model is KC-11FX, and it can be purchased for less than half of the price of other, simi­lar saws. On this purchase, I went with the suggestion of Jeff at Brettwood Machinery – he was right; a very good value saw that runs smooth, and has a decent fence.
Alternately, a detached shop can often be located closer to your property line and offers you a bit more freedom in terms of the type of foundation you can use. It may give you a sense of welcome separation from your home and open up yard space or allow a deck on the back of your house that would otherwise be lost behind your shop. In an urban setting, if you would like to have a wood stove in your shop you may find it more challenging to find an insurance carrier that allows one in an outbuilding. Also, outbuildings can be subject to more stringent height regulations than additions.
A board is considered “quarter-sawn” when the growth rings run, more or less, perpendicular to the face of the board. Quarter-sawn boards generally have straight grain and are less prone to shrinkage, compared to other boards. These factors don’t come into play with the 2x4s you use to frame a closet—but it does with the shelves and cabinetry you put into that closet; you want those boards to remain straight, flat and stable.

Finding affordable lumber has always been a mainstay for woodworkers, and when you tie our dwindling natural resources into the conversation the time is right to look at milling your own lumber. This seven-part weekly video series takes you through how to find lumber, how to operate a sawmill, details on types of sawing methods, stickering and drying and ultimately advice on using a mill as part of a business. Learn what you need to know to understand Milling Your Own Lumber.


The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
Here’s an easier way to stain or seal chairs, lattice or anything with numerous tight recesses. Pour the stain into a clean, empty spray bottle ($3). Spray the stain onto the project and wipe up the excess with a brush or rag. The sprayer will squirt stain into all those tight, hard-to-reach cracks and joints. — Valrie Schuster. Learn more about staining wood.
Hard to determine which stain you need in that bespattered collection of cans? An easy-to-make “stain index,” courtesy of reader Bob Jacek, solves the problem. Section off boards of your favorite woods into squares with masking tape, and apply the different stains across the width of each wood type (pine, oak, birch, etc.). When the stains are dry, brush on lengthwise your regular finishes—polyurethane, water-based polyurethane, oil, orange shellac, etc. You’ll be able to tell how each stain looks with each finish. Label each one. Use both sides of each board, and you’ll have a wooden encyclopedia of stain and finish combinations. Plus: How to stain wood evenly.
The beauty of a portable A/C unit is that you don’t have to heft it into a window and block off a valuable source of fresh air for keeping paint fumes at bay. Instead, choose a model with a low profile that you can tuck under a table or against a wall when not in use — a model with casters for maximum maneuverability is ideal. Choose a high-powered unit that will condition at least 400 square feet of space and move it where you need it for maximum comfort as you work.
In the above video Will Myers teaches the basics of woodturning for woodworkers. He starts by showing how to prepare and center the wood, then discusses woodturning tools & parts of the lathe. And finally he begins roughing out a spindle for a classic cherry shaker candle table. This tutorial comes from the class and DVD: "Building the Hancock Shaker Candle Stand with Will Myers". If you'd like to build this historical candle stand along
Gone are the days when you could apply for a building permit based on a sketch on the back of a cigarette pack­age. In provinces like Ontario, design work must be undertaken by an insured designer registered under the provin­cial building code or by the owner of the property. You can do the drawings as the owner if you can demonstrate effec­tively through your drawings that your structure will comply with the techni­cal requirements of the building code in a clear and concise way. You will be required to submit detailed drawings, including the following:
Before you buy a single tool, you need to take a hard look at your workshop space. If your workshop is a freestanding building or empty barn, you can simply measure the perimeter and know that you have the entire square footage at your disposal including the wall space. If your workshop is tucked into the back of a garage or a corner of partially finished basement, you’ll need to plan your furnishings with cars and water heaters in mind.
×