To plan my shop, I used a modeling program on my computer, but you can use the drawings I created to plan an efficient shop on paper. Download and print the PDF below and arrange them on graph paper to create a plan view of your shop. Take the time to work out the most efficient placement of benches, cabinets, and machines, taking into account infeed and outfeed zones as well as ducting for dust collection.
The second corner of the triangle is in the center of the room and, in our case, is where the workbench is located. Following work progress in sequence, the workbench is typically the second workstation where medium-duty work is done after heavier preparatory or wood-milling steps are finished. The workbench is where work is typically done using hand tools or smaller power tools such as hand drills, routers and joinery tools.
Sanding the inside of a hole or curved surface can be difficult. To simplify that task, insert a 1/4 x 3-in. bolt into the pilot hole of a hole-saw cutout. Secure the bolt with a washer and nut. Using a hacksaw, cut a 1/4-in. deep slot in line with the bolt. Cut a piece of adhesive-backed sandpaper so that you can slide one end into the slot, wrap it around the cutout, and slide the other end back into the slot. Chuck the bolt into a drill, and you now have a homemade drum sander. — E.R. Comstock. How to Sand Wood Faster
A landscape designer friend of mine tells a story about the college he went to. During his years there, the university embarked upon an ambitious building plan, adding several large structures around the main quad: a dorm, a chemistry lab, and a couple of others. The look of the place, which had remained unchanged for a century, was suddenly transformed, as glass-and-steel modernist structures were interspersed with the earlier ivy-covered stone Victorian-Gothic.
Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.
Tabletop versus Freestanding Tools. When purchasing some power tools (the list includes the jointer, shaper, sander, and even some models of table and band saw), you may decide to opt for benchtop models. A single bench can then serve, alternately, a range of purposes. Make- ready time is increased significantly, of course, as not only the blades, fences, miter gauges, and the rest must be set but the machine itself has to be positioned and powered. But for the small shop, the infrequently used tool may be quite easily stowed on a shelf out of the way, opening up more space for other tasks.
In addition to keeping your workshop comfortable with climate control add-ons, don’t forget to keep your body in optimal condition as you work. A water cooler tucked away in the corner of your workshop will provide a big quality of life boost and allow you to keep at your projects without having to run to the kitchen for a glass of water every time you feel thirsty.
Shops have value on many different levels. There is the satisfaction of having a place to create and work on projects that is hard to quantify, but definitely improves your quality of life. There is the value to your small business of having space in which to work wood and thereby generate income. There is the dollar value of the build itself, which will be a considerable investment and, finally, there is the resale value of your property after you’ve added your shop. Before you go too far, though, it’s worth asking a local real-estate agent about the potential return on your investment in your area; generally shops won’t add significantly to the value of your property, so it’s worth thinking carefully about what else the space could be used for if you were to sell. The decision about whether it is worth it to build is a matter of balancing all these factors: projected sales balanced against the cost; the cost of building is balanced against what it will be worth when you sell. Woodworking can be a creative outlet, can give you a sense of mastery, and even be a way to give back to your community by donating beautiful pieces to local charities for fundraising auctions, or creating pieces that future generations will inherit. Ultimately, the value of a shop might come down to the emotional and social returns that it will pay you and the people around you for years to come.
Just as a shed or garage can get stifling in the summer heat, winter cold can also make working conditions difficult — if not impossible. To prevent clumsy, stuff fingers from ruining your projects, you need a way to heat your workshop in even the most extremely frigid days of the year. A traditional residential space heater probably won’t cut it, as these are designed to heat single rooms. For a two-car garage or full basement, you’ll need something much bigger.
Even if you buy your lumber already planed, you will still encounter many circumstances that require the use of a planer. For example, you might want to build a simple and delicate jewelry box out of small scrap pieces lying around the shop, and you will end up making a small and clunky jewelry box because all of your lumber is 3/4″ thick, and that’s how it is going to stay. That is just the first example. Think about all of the other times that you will pick up a piece of lumber in the shop and it will be the wrong thickness, either just slightly wrong or in an entirely different size category. A planer is a real problem solver and can fix all of that.
Here’s an easier way to stain or seal chairs, lattice or anything with numerous tight recesses. Pour the stain into a clean, empty spray bottle ($3). Spray the stain onto the project and wipe up the excess with a brush or rag. The sprayer will squirt stain into all those tight, hard-to-reach cracks and joints. — Valrie Schuster. Learn more about staining wood.
Hard to determine which stain you need in that bespattered collection of cans? An easy-to-make “stain index,” courtesy of reader Bob Jacek, solves the problem. Section off boards of your favorite woods into squares with masking tape, and apply the different stains across the width of each wood type (pine, oak, birch, etc.). When the stains are dry, brush on lengthwise your regular ﬁnishes—polyurethane, water-based polyurethane, oil, orange shellac, etc. You’ll be able to tell how each stain looks with each ﬁnish. Label each one. Use both sides of each board, and you’ll have a wooden encyclopedia of stain and ﬁnish combinations. Plus: How to stain wood evenly.
To experiment with different wood shop layouts, measure your furniture and equipment to sketch onto your plan in different positions. You can also make cutouts of the footprint of your items so you can easily move them around your floor plan to see how best to arrange them. As you do so, don’t forget to leave adequate spacing around tools and tables.
The planners did an interesting thing, my friend recalls. Instead of commissioning a hugely expensive study to try to predict the new patterns that would result from the opening of the new buildings, rather than devising an anticipated program and laying out a new scheme, the university’s brain trust decided to let the students and faculty, the lifeblood of the university, shape their own arterial flow.
This is a fundamental question. A good place to start is with a survey of your property. Most municipalities have a maximum percentage of your lot that you can build on and standard setbacks from your property lines that you will need to adhere to without needing to request special permission to build. On a photocopy of your survey you can draw in what your local setbacks are in order to define the location within which you will be permitted to build. In a best-case scenario, you will have the space to build without compromising too much on space or location; otherwise, you may need to request a minor variance, which would allow you to circumvent an obstacle such as a setback.
If your shop lacks wall space or doesn’t have a long enough wall to accommodate long stock, another option is to place the crosscut saw near an operable doorway with the right-hand side closest to the door (see option 2 in the illustration). This leaves most of the length of the fence to the left of the blade (preferable if you’re right-handed), allowing short and mid-sized parts to be cut to length or trimmed without having to open the door.