I use binder clips for a lot of things around the shop, and here’s one that I thought I’d share. When I need to make multiple cuts all the same length, I just clamp my jumbo binder clip to my fence and use a 1/4-in.-thick wood scrap pinched in the clip as a stop. Works like a charm! When it’s not in use, I clamp it to the cord so it’s always nearby. — John Muchow
In the above video Will Myers teaches the basics of woodturning for woodworkers. He starts by showing how to prepare and center the wood, then discusses woodturning tools & parts of the lathe. And finally he begins roughing out a spindle for a classic cherry shaker candle table. This tutorial comes from the class and DVD: "Building the Hancock Shaker Candle Stand with Will Myers". If you'd like to build this historical candle stand along
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strap­ping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.
In addition to sheer power, look for a model with a built-in thermostat so you can set it and forget it. This convenience feature is well worth it so you don’t have to stop what you’re doing mid-project to manually turn your heater on and off to maintain your desired temp. A good garage heater will mount to the wall or ceiling to save space and will come with a durable housing and full safety screen to keep dust and wood chips from reaching the heating elements and starting a fire.
Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wir­ing for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to fin­ishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a program­mable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.
Not happy with the selection of sanding blocks at the hardware store, I made a few of my own from hardwood scraps left over from a woodworking project. I cut each one to 3/4 in. x 1-1/2 in. x 4-1/2 in.—which is just the right size to wrap a quarter sheet of sandpaper around. And the “kerf” cut helps hold the sandpaper in place until I’m ready to change it. —Tim Olaerts. Here are 41 more genius sanding tips you need to know.

In most small shops, once the key machines are in place, others are arranged wherever there is room for them. There typically isn’t enough free space for these tools in the middle of the floor area, although sometimes you can tuck a machine into an unused space. For example, in a shop where the table saw is in the center, a shaper (or a router table or spindle sander) with a table the same height as the saw can be put on the outfeed side of the extension table (see the illustration). Also, building a router table directly into the table saw’s extension table is a great way to save space, as well as make use of the saw’s fence for routing operations.
Welcome to The Woodwork Shop, Inc. We are glad you are here!  We are a locally owned and operated woodworking shop, serving the greater Memphis Metropolitan area.  Located just off of I-40 in Bartlett we are easy to get to from just about anywhere.  We have over 5000 square feet totally devoted to woodworking and woodworking equipment, and a very knowledgeable staff.  We have FREE Saturday Seminars every Saturday at 10:30am, and also offer weekly classes on Monday nights. Come on in, or give us a call if you have questions at (901) 755-7355 or email us at thewoodworkshopinc@gmail.com.  We can’t wait to see you!
Lacking a jointer? Use reader Court Kites’ awesome tip to create perfectly matched glue joints on wavy or bowed board edges. Lay the boards on a flat surface, then clamp them across the middle with a bar clamp. Lay two 8-in. long by 1-3/4 in. wide scrap boards across each end and screw them in with four 1-1/4 in. long screws, two per board. Keep the screws well away from your future cutting line!

Is your cellar damp? If so, you may have to correct that problem before installing your tools and lumber supplies. Insulate pipes to prevent condensation. Make sure your gutters outside keep rainwater running away from the house. Cracks in the cement floor or walls should be filled with hydraulic cement; a high water table may necessitate a sump pump to collect water at a low point and pump it out. Any or all of these circumstances may also require a dehumidifier. In any case, dampness is unacceptable where power tools are to be used because of the risk of electric shock.
An interesting variation of this layout is displayed in Jim Tolpin’s shop, shown in the photo at right. Tolpin located his jointer to the left of his table saw, its height low enough to allow panels cut on the saw to pass over the jointer. To save space, his portable planer lives beneath the saw. All three tools are oriented toward the garage-style door, which can be opened to allow long boards to be ripped, jointed, or thickness planed.
×