To make the most of your workshop oasis, look for a water dispenser that offers a choice between chilled and hot water. This will let you enjoy a cold, refreshing drink in the heat of summer rather than a lukewarm bottle that’s been sitting around gathering dust. You’ll also cut down on the amount of plastic your household goes through, which is a boon for the environment. In the winter, the hot water tap will also you to make a cup of tea or a mug of instant coffee on the spot. No matter what your taste, a versatile drink dispenser will keep you hydrated and happy while you work.
Low-tech tools are high on value A basic set of handplanes lets you true edges, flatten panels or wide boards, and achieve finish-ready surfaces. Start with a small cluster of handplanes—low-angle and standard block planes, a No. 4 or 4-1/2 bench plane, and a jointer plane. A set of inexpensive chisels is essential for chopping, paring, and trimming.
Sanding the inside of a hole or curved surface can be difficult. To simplify that task, insert a 1/4 x 3-in. bolt into the pilot hole of a hole-saw cutout. Secure the bolt with a washer and nut. Using a hacksaw, cut a 1/4-in. deep slot in line with the bolt. Cut a piece of adhesive-backed sandpaper so that you can slide one end into the slot, wrap it around the cutout, and slide the other end back into the slot. Chuck the bolt into a drill, and you now have a homemade drum sander. — E.R. Comstock. How to Sand Wood Faster
That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000.
Before you buy a single tool, you need to take a hard look at your workshop space. If your workshop is a freestanding building or empty barn, you can simply measure the perimeter and know that you have the entire square footage at your disposal including the wall space. If your workshop is tucked into the back of a garage or a corner of partially finished basement, you’ll need to plan your furnishings with cars and water heaters in mind.
After a permit has been issued, the building inspector will want to be notified at various points during your build in order to do a site visit, walk around and inspect the details to make sure that they meet code requirements. These inspections are commonly at the point where excavation work is complete, when the foundation is completed but before back-filling, when framing and all structural work has been done, after the installation of the insulation and vapour barrier, and then a final inspection after everything is complete. You may need to have a separate plumbing inspector if you’re adding or changing plumbing fixtures, and electrical work will need to be inspected by the appropriate electrical inspector (in Ontario, the Electrical Safety Authority). In my experience, inspectors appreciate good work, a clean, safe site, and are willing to work with homeowners and builders to make sure that the work will meet code and will endure.
I am often surprised at what tools woodworkers don’t use or own, especially when they are some of the few that I find essential. Sometimes it’s just the difference between hand tool and power tool guys, but sometimes it’s just from lack of experience or the fact that they haven’t given it too much thought. Most likely they just buy tools as they need them and never really considered what tools would give them the most bang for the buck.
With the right tools and materials, what you build is only limited by your imagination and creativity. So why not have a little fun with the kids and teach them something at the same time? Our woodworker tools and woodworking supplies will help you put together an easy birdhouse, squirrel feeder or butterfly house. The kids will love to use our paint samples to add their creative touch, and will enjoy displaying the finished product in the backyard.
Impact driver: I am a giant fan of impact drivers. I have been using them for a while now and can’t really remember my life before them (Click here to read more about my introduction to impact drivers). This is the one tool that I always have with me, and I expect to be within easy reach. So much so, that I own three of them and could imagine myself with a couple more. Like the chop saw, if this was a list of on-site or installation tools, the impact driver would be near the top.
High-velocity fans are also an important tool in their own right, particularly at your finishing station. Increased air flow will help dissipate fumes from paints and sprays for your safety, and you can train a fan on your project to help paint dry more quickly between coats on humid days. To get the most out of your fan, look for floor fans that are easy to aim or wall-mounted fans that will save space in smaller shops.
An interesting variation of this layout is displayed in Jim Tolpin’s shop, shown in the photo at right. Tolpin located his jointer to the left of his table saw, its height low enough to allow panels cut on the saw to pass over the jointer. To save space, his portable planer lives beneath the saw. All three tools are oriented toward the garage-style door, which can be opened to allow long boards to be ripped, jointed, or thickness planed.