These are all good tips, and apply to pretty much every shop. Like all things woodworking they need to be tweaked so that it’s right for the individual. For instance, I have a basement shop that’s not tiny but it is still space constrained, so worrying about the optimal layout for my ts/jointer/planer is a little off the mark since I don’t have to walk very far; instead, I want to be sure that related tools can be used *at the same time*. Having to move the planer out of the away so that I can use my TS is crazy if it can be avoided. However, interference between my drill press and my planer is less of an issue because they usually don’t get used at the same phase of a project.
Much like the assembly table, nearly every project in my shop makes extensive use of the table saw. And like it or not, my outfeed table becomes a second storage area for project parts and cut-offs. So I like to have mine located in the middle of the shop for the same reasons as the assembly table. Additionally, it’s nice to have ample space around the tablesaw for those larger workpieces. Unless it’s absolutely necessary, I’m not a fan of storing the table saw against a wall.
Pocket screw joinery is a system—employing special drill and driver bits—used to join boards or pieces of plywood to one another. Installing pocket screws involves using a jig to drill a sharply angled, 15-degree hole through the back of one board, then driving a special screw through that hole into the second board to draw them tightly together. Learn how to use pocket screws here. It’s often used in cabinetmaking and furniture building. Here’s how to build cabinets with pocket screws. The term “pocket” comes from the design of the hole which contains an upper “pocket” for the head of the screw to push against; this pocket also hides the head of the screw.
If you have a fixed-in-place cutoff saw (a radial-arm, miter saw, or sawbuck, for example), it can, unlike the table saw, be conveniently positioned against a wall. Don’t set it in a corner, however, as you’ll need space on either side of the blade. Figure into your plan a two-foot-deep, three-foot-wide space for the saw itself and tables or other supports flanking the tool. Allow enough space directly in front of the saw for the operator to be able to comfortably line up and operate the saw.
Efficiency does not always increase with experience, because as our woodshops grow older, they sometimes become unnecessarily rearranged or cluttered. And if you’re just now setting up your first woodshop, this shop layout should give you a great starting point. Each picture represents one half of a standard two-car garage. Click on the images for a larger view, and if anything is unclear, ask a question in the comments field!
My shop ended up being 23 x 19 feet, for a total of 437 square feet. I put my wood rack in the basement, but outside the walled in shop area. To keep the dust in the shop, a three part strategy was employed. I have a dust collection system, an air filtration system and a shop vacuum for cleaning dust out of machinery. I put up new walls, installed new electrical service, lighting, and two access doors for ease of materials movement. The shop includes two windows so that I can enjoy natural light, and not feel like I am squirreled away in the basement.
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
Keep in mind, there are no perfect boards, but try to always use the straighter boards and avoid warping boards. Also, Brandon and I have found that when it comes to picking out lumber at Home Depot and Lowes, they tend to stock up on fresh boards a few days before the weekend starts (so Thursday/Friday). And then, on Sundays and Mondays, the boards are usually really picked over and there isn’t a good selection. Just another tip to keep in mind!
Position #3 is where you will likely spend most of your time in the shop. The diagonally placed workbench is the heart of this plan. The wall-mounted workspace that surrounds the bench forms an ideal “work triangle” within which each of your most commonly needed tools is only one or two steps away. The band saw can be placed outside of the work triangle because it is used slightly less frequently and often needs a little more space around it for your lumber to move.
No matter what woodworking or tool-related venture you're taking on, Amazon.com has the trustworthy brands delivering the helpful products you'll want, brands like Dewalt, Makita, Stanley, Black + Decker, Festool, Shop-Vac, Jet and more. You'll also find a wide range of deals and special offers on woodworking products in the Deals and Savings page. Shop on Amazon.com and get free shipping for qualifying orders.
Often times at first glance a board looks straight and the fact that it is actually bowed or has some warping isn’t always obvious. So the trick to knowing for sure, is to hold the board up towards your face, with the other end on the ground, and look at it at a downward angle (as shown in the below photo). This method will allow you to see if it is bowing at all.
Impact driver: I am a giant fan of impact drivers. I have been using them for a while now and can’t really remember my life before them (Click here to read more about my introduction to impact drivers). This is the one tool that I always have with me, and I expect to be within easy reach. So much so, that I own three of them and could imagine myself with a couple more. Like the chop saw, if this was a list of on-site or installation tools, the impact driver would be near the top.
Let’s face it, one of the most significant costs of your shop will be its foundation. While you’re at it, what about adding space above your shop? There may be regulations preventing you from building living space above your shop if it is in an urban setting or in an outbuilding, but there may be some flexibility depending on where you live. It is in the municipality’s interests to encourage infill housing that uses existing infrastructure. At a minimum, think about including attic trusses to create some space above your shop for drying lumber or storing equipment. Access could be from simple pull-down attic stairs or from the exterior if you don’t want to lose floor space to a stair or ladder. If you’re creating an addition to your house, you may be able to add a couple of rooms you’ve always wanted, such as a family room, office or in-law suite.
Tabletop versus Freestanding Tools. When purchasing some power tools (the list includes the jointer, shaper, sander, and even some models of table and band saw), you may decide to opt for benchtop models. A single bench can then serve, alternately, a range of purposes. Make- ready time is increased significantly, of course, as not only the blades, fences, miter gauges, and the rest must be set but the machine itself has to be positioned and powered. But for the small shop, the infrequently used tool may be quite easily stowed on a shelf out of the way, opening up more space for other tasks.
A landscape designer friend of mine tells a story about the college he went to. During his years there, the university embarked upon an ambitious building plan, adding several large structures around the main quad: a dorm, a chemistry lab, and a couple of others. The look of the place, which had remained unchanged for a century, was suddenly transformed, as glass-and-steel modernist structures were interspersed with the earlier ivy-covered stone Victorian-Gothic.
Popular and easy to work with, cherry is in high demand for its reddish-brown color and ease of staining and finishing. Cherry likely won’t be at the local home center, but should be at a lumberyard for a somewhat expensive price. This hardwood is a very common material for furniture, and is resistant to normal wear-and-tear, but it is best for indoor pieces.
In a woodworking shop, lumber storage is key, and it’s best to design shelves or racks that are about 50 percent larger than you think you need — you’ll almost certainly acquire more materials as the years go on. To maximize a small space, use walls by mounting shelves to the ceiling and purchasing a sturdy step ladder to help you reach things. A wall covered in standard pegboard and outfitted with hooks allows you to customize hand tool storage and keep your most-used hardware within easy reach.