Iron-on edge-banding is a quick way to cover up an edge on plywood. Trimming the excess, however, is tricky. I’ve tried edge-banding trimmers, but I find the results are unpredictable. With the trimmers I’ve tried, it wasn’t easy to change the direction of the cut to suit the grain direction of the edge-banding. If you’re cutting against the grain, you’re likely to tear out a chunk of your new edge-banding. Instead, I use a wide, sharp chisel. This way, I can read the grain direction and trim accordingly. Angle the chisel slightly and go slow, raising the back corner of the chisel just enough so that it doesn’t dig into the plywood veneer. Smooth the corner with a sanding block after trimming. Check out this amazing edge band veneering project!
Table saw: Of all of the tools in the shop, the table saw is the most useful and versatile. It excels at making straight cuts, and with the addition of any of a million jigs, can be made to perform an amazing number of tasks with repeatability and precision. I use the table saw for roughing out smaller parts from larger pieces, all the way through trimming parts to final size. The only limit to the table saw is that the piece needs to be small enough to be pushed through it. Above a certain size, the table saw becomes less useful and even impossible to use as the saw needs to be brought to the piece, instead of the piece being brought to the saw.
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
If your shop lacks wall space or doesn’t have a long enough wall to accommodate long stock, another option is to place the crosscut saw near an operable doorway with the right-hand side closest to the door (see option 2 in the illustration). This leaves most of the length of the fence to the left of the blade (preferable if you’re right-handed), allowing short and mid-sized parts to be cut to length or trimmed without having to open the door.
I know this seems really simple and you may already know how to read a tape measure so just hear me out on this one! Often times with woodworking you need to make exact measurements and cuts and it’s rarely pretty even numbers like 15 inches or 15 1/2 inches. It’s usually like 15 5/8 inches or 15 9/16 inches. So, really knowing how to read a tape measure in its entirety is important. And I’ve created a quick post on how to read a tape measure the easy way along with a helpful free printable.
In my shop I use a large number of Jorgenson F-clamps. I use many of the small clamps, the most useful being the 12" version. Large F-clamps are essential for cinching down parts on bending forms. I also like aluminum bar clamps because they are much lighter than steel clamps, and therefore less likely to damage a carcase should you bang into the wood during a glue-up.
This is a fundamental question. A good place to start is with a survey of your property. Most municipalities have a maximum percentage of your lot that you can build on and standard setbacks from your property lines that you will need to adhere to without needing to request special permission to build. On a photocopy of your survey you can draw in what your local setbacks are in order to define the location within which you will be permitted to build. In a best-case scenario, you will have the space to build without compromising too much on space or location; otherwise, you may need to request a minor variance, which would allow you to circumvent an obstacle such as a setback.