Your sense of space and how to use it will be slightly different depending on the focus of your craft. If you are building furniture with hand tools, you will be able to make do with less space (under 300 sq ft.) than if you’re using mainly power tools and building sets of cabinets (over 400 sq ft.). Some 3D modelling with a program like Sketch-Up or some 2D layouts on graph paper with scaled cutouts can allow you to experiment with arranging your space and how much of it you will need. You should include not only the tools, benches and storage that you currently possess but also enough room to tackle new types of projects and new tools that you anticipate needing down the road. When you think you have a layout that works, test it out by mentally working through a range of different projects you might tackle and the needs you will have for material storage, assembly and finishing. Then revise as necessary; this process will allow you to hone in on a general square footage and layout ideas that will set you up to move forward.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected. We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
In most small shops, once the key machines are in place, others are arranged wherever there is room for them. There typically isn’t enough free space for these tools in the middle of the floor area, although sometimes you can tuck a machine into an unused space. For example, in a shop where the table saw is in the center, a shaper (or a router table or spindle sander) with a table the same height as the saw can be put on the outfeed side of the extension table (see the illustration). Also, building a router table directly into the table saw’s extension table is a great way to save space, as well as make use of the saw’s fence for routing operations.
Instead of using a container to mix a small amount of epoxy, just make a mixing surface on your workbench using painters tape. Simply lay down strips, overlapping the edges so the epoxy doesn’t get on your bench. When you’re done, peel off the tape and throw it away. This mixing surface will work for more than just epoxy, you can use it for wood glue or any other material you need easy access to while working on a project.
Natural Light. Natural light is best, so any windows that offer illumination to the space should be put to good use. If you have little sunlight in your shop, locate your workbench so that its work surface gets whatever there is. Even the best eyesight is made better by good light, so the close work to be done on a benchtop benefits from the natural light.
No matter what woodworking or tool-related venture you're taking on, Amazon.com has the trustworthy brands delivering the helpful products you'll want, brands like Dewalt, Makita, Stanley, Black + Decker, Festool, Shop-Vac, Jet and more. You'll also find a wide range of deals and special offers on woodworking products in the Deals and Savings page. Shop on Amazon.com and get free shipping for qualifying orders.
In the above video James "Jim" Huggett shares a recent tour of his Furniture Making workshop in Earlysville, Virginia, just a few miles from the Wood And Shop Traditional Woodworking School. Jim reached out to me over a year ago, after he learned that my shop & school were just down the road from him. I dropped by his workshop (J.F. Huggett Custom Furniture), and was amazed that such an accomplished and skilled furniture maker
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
Table saw: Of all of the tools in the shop, the table saw is the most useful and versatile. It excels at making straight cuts, and with the addition of any of a million jigs, can be made to perform an amazing number of tasks with repeatability and precision. I use the table saw for roughing out smaller parts from larger pieces, all the way through trimming parts to final size. The only limit to the table saw is that the piece needs to be small enough to be pushed through it. Above a certain size, the table saw becomes less useful and even impossible to use as the saw needs to be brought to the piece, instead of the piece being brought to the saw.
Before you buy a single tool, you need to take a hard look at your workshop space. If your workshop is a freestanding building or empty barn, you can simply measure the perimeter and know that you have the entire square footage at your disposal including the wall space. If your workshop is tucked into the back of a garage or a corner of partially finished basement, you’ll need to plan your furnishings with cars and water heaters in mind.
Second, learning how to read lumber dimensions, like knowing what 1×2 or 2×12 actually means, is really important. Understanding softwood lumber dimensions will help you to read woodworking build plans, shop for lumber, and understand the general measurements for your projects. I’ve provided a simple explanation to lumber sizes along with a free lumber size chart printable here!
A receptacle or circuit that is overloaded is a hazard, in particular one fused beyond its limits. Power tools, especially heavy-duty saws, require lots of amperage, and you may need to add a circuit or two to serve the increased demand in your workshop space. Some tools require 220-volt service, so you may want to install a special plug and line to power that high-powered table saw.
Finally, think about the overall color and feel of your workshop. A fresh coat of bright white paint will help your lighting go farther, but you might also consider adding a splash of color for fun. An accent wall or an epoxy floor coating are good ways to upgrade your workshop from drab to fab without adding fussy decorations that will get in the way of business.
WoodAndShop.com recommends products, with links to online stores, some of which are part of affiliate programs. If users make purchases in those stores (e.g. ebay.com and Amazon.com) those affiliate links lead to referral compensation to us. These payments are very helpful to us, and add no additional fees to our users, so we are grateful for anyone who uses the affiliate links. We run our website based on principles of integrity, and don’t recommend any product that we wouldn’t use ourselves. Any product claim about a service or product should be verified with the manufacturer.
Often times at first glance a board looks straight and the fact that it is actually bowed or has some warping isn’t always obvious. So the trick to knowing for sure, is to hold the board up towards your face, with the other end on the ground, and look at it at a downward angle (as shown in the below photo). This method will allow you to see if it is bowing at all.
I mix a lot of epoxy in small batches, but I’ve seldom had the right size container on hand. I solved this problem by drilling 1-1/2-in. holes in 2×4 scraps with a Forstner bit. The resulting shallow “cups” allow easy mixing without the risk of spilling. When the holes are used up, I just make a new mixing board. — Bill Wells. Save your takeout utensils to use in the shop!
While trying to trace an exact copy of the throat plate for my table saw, I came up with this nifty technique using an ordinary pencil. I just shaved my pencil into a half-pencil by carefully grinding it on my belt sander. The flat edge enables my modified pencil to ride straight up along the edge of the template. It also works great for marking and then shaping inlays for my woodworking projects. — Tim Reese. How to cut circles with a band saw.
After a permit has been issued, the building inspector will want to be notified at various points during your build in order to do a site visit, walk around and inspect the details to make sure that they meet code requirements. These inspections are commonly at the point where excavation work is complete, when the foundation is completed but before back-filling, when framing and all structural work has been done, after the installation of the insulation and vapour barrier, and then a final inspection after everything is complete. You may need to have a separate plumbing inspector if you’re adding or changing plumbing fixtures, and electrical work will need to be inspected by the appropriate electrical inspector (in Ontario, the Electrical Safety Authority). In my experience, inspectors appreciate good work, a clean, safe site, and are willing to work with homeowners and builders to make sure that the work will meet code and will endure.
If your shop will be attached to your house or another structure, it will likely need to match its foundation, tying the two structures together so that one does not structurally stress the other if they shift differently. That may dictate a poured concrete or concrete block foundation. Regardless of your foundation type, a cold concrete floor will sap energy away from the rest of the structure if you are not careful, so think about how to insulate it well before you build.
I know this seems really simple and you may already know how to read a tape measure so just hear me out on this one! Often times with woodworking you need to make exact measurements and cuts and it’s rarely pretty even numbers like 15 inches or 15 1/2 inches. It’s usually like 15 5/8 inches or 15 9/16 inches. So, really knowing how to read a tape measure in its entirety is important. And I’ve created a quick post on how to read a tape measure the easy way along with a helpful free printable.
Examples of Bronze Age wood-carving include tree trunks worked into coffins from northern Germany and Denmark and wooden folding-chairs. The site of Fellbach-Schmieden in Germany has provided fine examples of wooden animal statues from the Iron Age. Wooden idols from the La Tène period are known from a sanctuary at the source of the Seine in France.
Each entry must feature some kind of inlay. This can be wood, glass, metal, etc. Epoxy pours are not allowed per /u/kevin0611's request. An epoxy pour does not count as an inlay for the sake of this contest. (Example would be cutting a pattern on CNC or by hand then filling with a colored epoxy to give the illusion that it's inlay.) Bowties, marquetry, and banding are good examples of allowed inlay in this contest.
The frost generated by Canadian winters wreak havoc on structures through their foundations. According to code conventional foundations and footings must rest below the reach of frost on undisturbed soil (in most provinces, this is safely considered to be 4 ft. below ground level or grade), bear directly on bedrock, or be frost-protected. A shallow foundation may be possible in your area in an outbuilding if you can get an engineer to design and stamp plans for insulating the area directly beside your shallow foundation wall so that frost will not form beneath the footing area and cause damage. A slab-on-grade foundation for an outbuilding is another option that will need to be designed by an engineer so that the concrete slab will structurally bear the weight of the shop structure you build above it.
Even if you buy your lumber already planed, you will still encounter many circumstances that require the use of a planer. For example, you might want to build a simple and delicate jewelry box out of small scrap pieces lying around the shop, and you will end up making a small and clunky jewelry box because all of your lumber is 3/4″ thick, and that’s how it is going to stay. That is just the first example. Think about all of the other times that you will pick up a piece of lumber in the shop and it will be the wrong thickness, either just slightly wrong or in an entirely different size category. A planer is a real problem solver and can fix all of that.
The tablesaw—This tool is the backbone of nearly every shop, and for good reason. It allows unmatched precision in ripping parallel edges and crosscutting at a variety of angles. Most woodworkers find it crucial for the basic milling of stock. It is also suited to many joinery tasks, easily producing tenons, box joints, and—with a reground blade—the tails for dovetail joints.
Gone are the days when you could apply for a building permit based on a sketch on the back of a cigarette package. In provinces like Ontario, design work must be undertaken by an insured designer registered under the provincial building code or by the owner of the property. You can do the drawings as the owner if you can demonstrate effectively through your drawings that your structure will comply with the technical requirements of the building code in a clear and concise way. You will be required to submit detailed drawings, including the following:
When customers visit my shop we usually start by talking about their wood needs. If it is someone’s first time to visit I also try to get to know them, what they are looking for and what they are expecting from me. Half of them are just looking for rough cut wood, while the others are looking for wood that is processed a little bit more, perhaps jointed or planed, or even sanded. During our time together I get to understand their needs and abilities, and our discussion usually turns to the tools they have in their shop.
Once you’ve planned the basic layout of your workshop and have added all the tools and speciality appliances you need, take a last look at the overall design to make it aesthetically pleasing. Add overhead lighting for general illumination and task lighting over your work stations so you can see your project clearly. For maximum flexibility, you can mount clip-on work lights to nearby shelves and point them where you need them, knowing you’ll be able to move them about as required for different projects.
Enter the garage heater. These space heaters are specifically designed to warm up wide open areas and to function under much tougher circumstances than you’re likely to find in the average house. A well designed garage heater will offer at least 5,000 watts of heating power — enough to warm 750 square feet of space. A smaller heater might take off a bit of the chill, but to really warm your workshop — and keep it that way — you’ll need a heater of this size.