While trying to trace an exact copy of the throat plate for my table saw, I came up with this nifty technique using an ordinary pencil. I just shaved my pencil into a half-pencil by carefully grinding it on my belt sander. The flat edge enables my modified pencil to ride straight up along the edge of the template. It also works great for marking and then shaping inlays for my woodworking projects. — Tim Reese. How to cut circles with a band saw.
Lacking a jointer? Use reader Court Kites’ awesome tip to create perfectly matched glue joints on wavy or bowed board edges. Lay the boards on a ﬂat surface, then clamp them across the middle with a bar clamp. Lay two 8-in. long by 1-3/4 in. wide scrap boards across each end and screw them in with four 1-1/4 in. long screws, two per board. Keep the screws well away from your future cutting line!
Fir, also known as Douglas Fir, is very inexpensive and common at local home centers. It has a characteristic straight, pronounced grain with a red-brown tint. However, its grain pattern is relatively plain and it does not stain well, so Fir is commonly used when the finished product will be painted. While commonly used for building, this softwood would also be suitable for furniture-making as well.
My shop consists of a 9×16 storage building, with 3 feet being used for actual storage! I have a table saw, 13″ planer, lathe, sliding mitre saw, home made router table, small compressor, 5′ 4 drawer bench with vice, table top drill press, 6″ jointer, band saw, shop vac, wall mounted hand tool storage, clamp rack, power tool storage, and no room to turn around! But I put out a few nice pieces! Recently built, a 48″ entry table from 100 yr old milled poplar, coffee table from the same re milled red oak barnwood, and a little triangle shaped corner table from the left over red oak, a 7′ x48″ bookcase from old poplar, a small wall mounted poplar book case, and am presently working on a queen sized bed with a mixture of 100 yr old oak and new kiln dried oak, with drawbored pegging using black walnut from a tree from my yard! I’ve also made several mallets that I find useful from my firewood pile using Cherry, ash, hickory and white and red oak. Building anything in 108 sq ft is a challenge, but patience determination, and decent sales will make it work! One good point is that nothing is out of reach! Except maybe the bathroom!
Sanding small items is tricky, as they’re hard to clamp in a vise to work on them. So instead of bringing the sandpaper to the workpiece, I bring the workpiece to the sandpaper. I glue sheets of sandpaper to a piece of plywood; 60 and 100-grit on one side and 150 and 220-grit on the other. Spray adhesive works well for this. Since there’s sandpaper on both sides, my sanding board doesn’t slide around on the bench. Check out these small projects!
I mix a lot of epoxy in small batches, but I’ve seldom had the right size container on hand. I solved this problem by drilling 1-1/2-in. holes in 2×4 scraps with a Forstner bit. The resulting shallow “cups” allow easy mixing without the risk of spilling. When the holes are used up, I just make a new mixing board. — Bill Wells. Save your takeout utensils to use in the shop!
With these three power tools (and a few hand tools), I feel like I could make about 80% of the jobs that come through my shop on a daily basis. Obviously, some jobs will require more specialized power tools to complete, but these three probably find their way into almost all of my work. With that said, there are a few other tools that I couldn’t imagine being without and I feel need to be added to the list.
Timely article indeed. I’ve been playing with the shop layout tool on Grizzly’s website (http://www.grizzly.com/workshopplanner) which helps you see how tools fit in a specific shop size. However, your insight and experience really helps with ergonomic considerations. When I first built my shop, the first thing I did was installing a wall mounted work bench – as my fore fathers had all done – Big Mistake! Soon-to-be project: ripping it out and building a mobile work bench on wheels (like the one you have pictured).
In the above video James "Jim" Huggett shares a recent tour of his Furniture Making workshop in Earlysville, Virginia, just a few miles from the Wood And Shop Traditional Woodworking School. Jim reached out to me over a year ago, after he learned that my shop & school were just down the road from him. I dropped by his workshop (J.F. Huggett Custom Furniture), and was amazed that such an accomplished and skilled furniture maker
Next come two options for the table saw’s trusty sidekick, the jointer, as well as for the thickness planer. Because it’s usual to work between all three tools when dressing lumber, the first option, shown in the illustration, locates the jointer nearest the saw to the right of its extension table with the planer nearby. As with the table saw, it always makes sense to align these tools with the shop’s long axis.