Historically, woodworkers relied upon the woods native to their region, until transportation and trade innovations made more exotic woods available to the craftsman. Woods are typically sorted into three basic types: hardwoods typified by tight grain and derived from broadleaf trees, softwoods from coniferous trees, and man-made materials such as plywood and MDF.

The frost generated by Canadian winters wreak havoc on structures through their foundations. According to code con­ventional foundations and footings must rest below the reach of frost on undisturbed soil (in most provinces, this is safely considered to be 4 ft. below ground level or grade), bear directly on bedrock, or be frost-protected. A shallow founda­tion may be possible in your area in an outbuilding if you can get an engineer to design and stamp plans for insulating the area directly beside your shallow foundation wall so that frost will not form beneath the footing area and cause damage. A slab-on-grade foundation for an outbuilding is another option that will need to be designed by an engineer so that the con­crete slab will structurally bear the weight of the shop structure you build above it.


I have found that drawing everything to scale on grid paper is most helpful. That is what I am doing in preparation for my new shop. I will, however need to share that space from time to time with my wife’s hobby (hatching and raising chickens). Just a few in the spring till they get big enough to go outside. I am planning on a 26″ x 40″ building with infloor hydronic heat. Others have mentioned that you can’t have too much light, and I intend to use the 200 watt cfl’s to accomplish this, along with task lighting at each machine. Walls and ceiling will be painted white to reflect as much of that light as I can. I want to use the same type of floor treatment that Marc has used in his new shop. Marc, is it really expensive to do that? Or if a guy has never done that would it be better to hire out that job? Lumber storage I have not decided yet. I am fortunate that I am able to fell trees on our farm and have them cut up so I can stack and dry them. We have white oak, red oak, maple, cherry and pine. Although drying/storage will be in another building will still have to tote my boards around some.
Keep in mind, there are no perfect boards, but try to always use the straighter boards and avoid warping boards. Also, Brandon and I have found that when it comes to picking out lumber at Home Depot and Lowes, they tend to stock up on fresh boards a few days before the weekend starts (so Thursday/Friday). And then, on Sundays and Mondays, the boards are usually really picked over and there isn’t a good selection. Just another tip to keep in mind!
How do you divide 11-3/8-in. (or any other mathematically difficult number) into equal parts without dividing fractions? Simple. Angle your tape across the workpiece until it reads an easily-divisible dimension and make your marks with the tape angled. For example, say you want to divide an 11-3/8-in. board into three equal parts. Angle the tape until it reads 12-in., and then make marks at “4” and “8”. Plus: More measuring tips and tricks.
To experiment with different wood shop layouts, measure your furniture and equipment to sketch onto your plan in different positions. You can also make cutouts of the footprint of your items so you can easily move them around your floor plan to see how best to arrange them. As you do so, don’t forget to leave adequate spacing around tools and tables.
I set an initial budget of $10,000 to build the shop – everything from studs and drywall to hand tools and machinery. The final number was over by $1,000, but I’m still very happy with the result. The shop is now my haven, with a good sound sys­tem and good lighting. Every time I go back into the shop, it is exactly the way I left it, because it is my shop!
Shops can range from functional spaces adorned with unpainted wallboard to beautifully finished, painted, and trimmed-out spaces. Ultimately, I think it depends on your budget and how important your surroundings are to your mindset as you’re working, or to your clients’ if they will be viewing your shop. If finishing your shop will improve the quality of the work that you will produce, thereby relaxing or inspiring you, or showcase for your clients the quality of the work of which you are capable, it may be a worthwhile invest­ment. A more finished space may also allow for activities like parties or even a weekly poker game (as long as drinks stay off the tools).
Any serious woodworker knows that square and flat Any serious woodworker knows that square and flat stock is the key to producing fine work so it’s time to skip the hand tools and graduate to the JJ-6HHDX 6 in. long bed jointer. This beast boasts a helical insert cutter head with staggered carbide inserts yet runs quietly and ...  More + Product Details Close
Spray gun: Not every woodworking job gets a film finish, but most of mine do. And of those, everyone will meet a spray gun. For a million reasons, including making finishing fast and fun, I recommend using a spray gun whenever possible. It will raise your game and make you n0t hate finishing. (Click here to read my thoughts on purchasing a spray gun).

In addition to sheer power, look for a model with a built-in thermostat so you can set it and forget it. This convenience feature is well worth it so you don’t have to stop what you’re doing mid-project to manually turn your heater on and off to maintain your desired temp. A good garage heater will mount to the wall or ceiling to save space and will come with a durable housing and full safety screen to keep dust and wood chips from reaching the heating elements and starting a fire.
This style of saw will provide more power than a contractor-type saw and have the high-quality rip fence you need to do good work. However, because they are favored by professionals and serious amateurs, cabinet saws are harder to find on the used market. Scour the classifieds and online sales (be sure to check industrial auction sites as well), and do some networking. Check the bulletin board at your hardwood supplier and ask the proprietors if they know of anyone selling a saw. Also call local cabinet shops. They sometimes have a surplus tool sitting idle that they’d be willing to sell. Take your time in this step. A careful investment will pay dividends in the long run, but a well-intentioned compromise can cause long-term frustration.

Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
Use whatever image hosting service you like and post the link to /r/woodworking. The key here is it needs to be apparent that you've built the entry, and you follow the photo requirements listed in the contest rules. Submissions of finished photos only will not be accepted for entry. <-- I can't emphasize this enough, you absolutely need more than 2-3 photos for a valid submission. I will no longer accept entries that have albums that go from rough stock to 90% complete in one jump.
Plan to invest in a set of bench chisels, both standard and low-angle block planes, a No. 4 or 4-1⁄2 smoothing plane, and a No. 6 jack or No. 7 jointer. Between them, these planes will true edges, flatten glue-ups that are wider than your thickness planer, and tame tricky grain that would tear out with a mechanized planer. They also do fine trimming better than any other tools.
With strength, sturdiness, and durability, maple is a common material for furniture for the bedroom and even china cabinets. Maple is moisture-resistant and frequently displays stand-out swirls in the wood grain, an aesthetically pleasing differentiator from other hardwoods. While most commonly a lighter color, maple also can take stains and paint well.[13]
Short scraps of hardwood are too good to throw away but hard to store neatly. So I bought a 4-ft. tube form made for concrete footings, cut it in half (the cardboard-like material cuts easily) and set the tubes on end. I tack the tubes to a wall or a bench leg so they don’t fall over. With the wood scraps stored upright, it’s easy to find a piece just the right length. Tube forms are available in various diameters for $5 and up at home centers. — Bill Wells. Here’s another brilliant use for these concrete forms.
I’m helping my son (who is significantly disabled) get started with a business idea that he had — one that I’d think was brilliant even if I weren’t his Mom — brilliant enough that I’ve “retired” from my law practice and moved us from MO to GA. Having lost 99.9% of ALL of my tools in the move (even the big ticket items, nearly 30 years collection — stolen by the mover!) I am now re-investing in tools, limiting my purchases to what we must have rather than all the fun stuff I used to have. . . .(So sad).
A kind’a unrelated question. I just finished building the lumber storage rack/sheet goods cart from your “racking my brain..” video. I see you went with the metal wall storage rack in your new shop (which I would love also, just can’t afford) but, I was curious why you didnt put another sheet goods cart. Previously I had the stand up sheet goods storage box like I see your current pictures but, from what little I have used the cart, I like it better than the stand up storage. Its easier to get things in and out and see what all I have. The only draw back is that I can’t store as much on the cart as I could with the box storage.

For our customers who are passionate about woodworking, we offer an extensive selection of tools and accessories to help your woodworking projects come to life. Whether you are a professional carpenter, construction manager or simply wish to build a DIY project, you will find everything that you need on our Amazon.com Woodworking page. Our selection ranges from, screwdriver sets to air filtration, band saws, sanders, drill presses, dust collectors, jointers, laminate trimmers, lathes, planers, benchtop, plate joiners, belt sanders, router combo kits, shapers, sharpener, barn door hardware, circular saws, router tables, router bits, planer, tool box, wood glue, nail gun, table saws, hammers and more.
While trying to trace an exact copy of the throat plate for my table saw, I came up with this nifty technique using an ordinary pencil. I just shaved my pencil into a half-pencil by carefully grinding it on my belt sander. The flat edge enables my modified pencil to ride straight up along the edge of the template. It also works great for marking and then shaping inlays for my woodworking projects. — Tim Reese. How to cut circles with a band saw.
Shops can range from functional spaces adorned with unpainted wallboard to beautifully finished, painted, and trimmed-out spaces. Ultimately, I think it depends on your budget and how important your surroundings are to your mindset as you’re working, or to your clients’ if they will be viewing your shop. If finishing your shop will improve the quality of the work that you will produce, thereby relaxing or inspiring you, or showcase for your clients the quality of the work of which you are capable, it may be a worthwhile invest­ment. A more finished space may also allow for activities like parties or even a weekly poker game (as long as drinks stay off the tools).
In a woodworking shop, lumber storage is key, and it’s best to design shelves or racks that are about 50 percent larger than you think you need — you’ll almost certainly acquire more materials as the years go on. To maximize a small space, use walls by mounting shelves to the ceiling and purchasing a sturdy step ladder to help you reach things. A wall covered in standard pegboard and outfitted with hooks allows you to customize hand tool storage and keep your most-used hardware within easy reach.
×