A shop geared toward woodworking would have lumber storage located at one corner of the triangle. Storage space for wood — both long pieces and flat plywood pieces — should be adequate. Raised storage, such as racks or shelves mounted on the wall, must be sturdy. Wood storage should also be in close proximity to the stationary tools or machines (table saw, jointer, power planer, etc.) to avoid frequently carrying heavy wood across the span of the workspace. Wood storage should be handy and near the area where the heavy woodworking tasks will take place. Keep in mind that a considerable amount of space will be needed around stationary tools such as a table saws and jointers for manipulating large pieces of raw lumber.

This will be a personal matter, depend­ing on whether it will be helpful for finishing or sharpening. However, it is a good idea to look beyond your current use of this space to the next owner. Would it be beneficial to add plumbing hookups so that the shop could someday be an apart­ment, or an art studio, or an extension to your house? It could add to the resale value of your house to be able to create as flexible an area as possible by roughing in a bathroom and even a kitchenette area if you can. If this is done when wall cavities are open or before the slab is poured, your forethought could pay dividends but not cost much up front. 


I am also very tempted by the 10% package discount for combining the MFT/3 with the TS 55 REQ. …BUT: I already have a home-made workbench: 24″ x 62″ with 3/4″ bench dog holes in the double layer MDF top. It has a Jorgensen quick-release vise. {Copied from FWW’s “Getting started in woodworking” videos.} The only other work surface I have is a sheet of Melamine used as a router table (and is always cluttered with tools until I build some tool cabinets soon – hence the interest in LR32 & guide rail).
Timely article indeed. I’ve been playing with the shop layout tool on Grizzly’s website (http://www.grizzly.com/workshopplanner) which helps you see how tools fit in a specific shop size. However, your insight and experience really helps with ergonomic considerations. When I first built my shop, the first thing I did was installing a wall mounted work bench – as my fore fathers had all done – Big Mistake! Soon-to-be project: ripping it out and building a mobile work bench on wheels (like the one you have pictured).

Minor variances are applications to your municipality to suspend a particular by-law to allow your project to proceed, based on common sense or precedents set by other buildings in your area. If your municipal committee of adjustment denies permission because a neighbour voices concern over the development, you would have to appeal the decision to the municipal board of your particular province. In that case, you may be better off looking for another piece of property with an existing structure that you could renovate, more relaxed zoning regula­tions, a larger lot, or more congenial neighbours. 
Minor variances are applications to your municipality to suspend a particular by-law to allow your project to proceed, based on common sense or precedents set by other buildings in your area. If your municipal committee of adjustment denies permission because a neighbour voices concern over the development, you would have to appeal the decision to the municipal board of your particular province. In that case, you may be better off looking for another piece of property with an existing structure that you could renovate, more relaxed zoning regula­tions, a larger lot, or more congenial neighbours. 
To make the most of your workshop oasis, look for a water dispenser that offers a choice between chilled and hot water. This will let you enjoy a cold, refreshing drink in the heat of summer rather than a lukewarm bottle that’s been sitting around gathering dust. You’ll also cut down on the amount of plastic your household goes through, which is a boon for the environment. In the winter, the hot water tap will also you to make a cup of tea or a mug of instant coffee on the spot. No matter what your taste, a versatile drink dispenser will keep you hydrated and happy while you work.
Because workshops are rough and tumble places, the right fan for the job will have an industrial-strength motor and adjustable fan speeds. Easy-to-clean metal blades and a fully encased motor housing are also important features, especially if your shop tends to fill up with sawdust, wood chips and other fine debris. That extra layer of protection will help the fan motor last for years instead of being damaged by particulates.
Plan to invest in a set of bench chisels, both standard and low-angle block planes, a No. 4 or 4-1⁄2 smoothing plane, and a No. 6 jack or No. 7 jointer. Between them, these planes will true edges, flatten glue-ups that are wider than your thickness planer, and tame tricky grain that would tear out with a mechanized planer. They also do fine trimming better than any other tools.

Any serious woodworker knows that square and flat Any serious woodworker knows that square and flat stock is the key to producing fine work so it’s time to skip the hand tools and graduate to the JJ-6HHDX 6 in. long bed jointer. This beast boasts a helical insert cutter head with staggered carbide inserts yet runs quietly and ...  More + Product Details Close
Although refrigerators long ago rendered them obsolete, antique oak ice boxes remain popular with collectors, even though they’re expensive and hard to find. This do-it-yourself version is neither: it’s both inexpensive and easy to build. An authentic reproduction of an original, the project is especially popular when used as a bar, but it has many
Clamping up four mitered corners is tricky. You can buy specialty clamps for this, but I make my own. Here’s how to do it. Start with a long 1×4, as it’s easier (and safer) to clamp for making the angled cuts than a short piece. Mark out the blocks, and then drill a 1-in. diameter hole in the center of each one. The hole prevents the blocks from getting glued to your project. Cut 45-degree angles tangent to the hole, and then cut the blocks free from the long board. We’ll walk you through how to make one for your home shop.
To make sure you account for any existing obstructions, it’s a good idea to make a measured drawing of your workshop area on graph paper, noting existing furniture, built-ins and large items on the plan as you go. For example, a common one-car garage workshop layout has built-in tool cabinets and shelves around the perimeter where they won’t impede parking, but you may also have to get clever about folding work tables and saw horses that you can set up as needed in the middle of the garage when you’re working on a project (and cars are parked outside).
To plan my shop, I used a modeling program on my computer, but you can use the drawings I created to plan an efficient shop on paper. Download and print the PDF below and arrange them on graph paper to create a plan view of your shop. Take the time to work out the most efficient placement of benches, cabinets, and machines, taking into account infeed and outfeed zones as well as ducting for dust collection.
If a poured cement floor prohibits the installation of plug receptacles flush to the floor and you elect to surface-mount a plug, protect the exposed feed wire. A piece of one-by-four stock with a groove cut in its underside and its top edges chamfered, will pose little more tripping risk than a threshold. However, paint its protective covering a bright color to remind you and any other visitors to your shop of its presence.
That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000.
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here. 

Second, learning how to read lumber dimensions, like knowing what 1×2 or 2×12 actually means, is really important. Understanding softwood lumber dimensions will help you to read woodworking build plans, shop for lumber, and understand the general measurements for your projects. I’ve provided a simple explanation to lumber sizes along with a free lumber size chart printable here!
Set the table saw fence so the blade is centered on the seam, then push the whole thing through the saw. If the board edges are quite bowed or curvy, you may need a second pass. If so, unscrew the cleats, reclamp the boards across the middle center, then screw on the cleats again. The screws ding up the ends of the boards a little, so cut the boards you’re jointing a bit long, then trim 1/2 in. from each end to remove the screw holes.
The all-new JWBS-14DXPRO 14 in. Deluxe Band saw The all-new JWBS-14DXPRO 14 in. Deluxe Band saw from JET has been fully redesigned to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14 in. band saw comes with a massive cast iron frame for increased power that makes it ...  More + Product Details Close
When it comes to woodworking for beginners, I think it’s important to just learn how to use a few of the most essential woodworking tools for beginners. There are so many awesome tools available on the market today, it can be quite overwhelming as well as expensive to try to buy them all and know how to use them. Once you learn the basics of the most essential tools you will be able to start building in no time and feel comfortable learning any other new tools in the future.
In each case, we shuffled the bench, jointer, table saw, and band saw across to the top of the stairs, and then tied a rope around each to act as a safety while sliding the machines down the strapping on the stairs. Yeah, the table saw hit the wall, and the promise of a good mud and paint job saved my bacon. The rope worked well, and we were able to get everything down the stairs nice and slowly with­out any major issues.
Because of my son’s disability and my need to teach him just about everything, I have items sorted into bins with handles, labeled with the category (i.e, Sanding, Cutting, Measuring, etc). It’s over-simplified and over-organized, but necessary in our case. One thing nice about it is that we never waste time looking for something; everything has its place.
I looked around at many versions of Taiwanese drill presses. I ended up purchasing the Ridgid DP15501 15" drill press because I liked the way the quill stop was made, the work light, key stor­age, and the easy access to the belt change system. This machine was also on sale when I needed it, so that made it a slam dunk. Choose the one that suits you, as they’re all very similar. The table is large enough, and the distance to the column is large enough to allow you to do most anything a small shop needs. 
I’m helping my son (who is significantly disabled) get started with a business idea that he had — one that I’d think was brilliant even if I weren’t his Mom — brilliant enough that I’ve “retired” from my law practice and moved us from MO to GA. Having lost 99.9% of ALL of my tools in the move (even the big ticket items, nearly 30 years collection — stolen by the mover!) I am now re-investing in tools, limiting my purchases to what we must have rather than all the fun stuff I used to have. . . .(So sad).
The planners did an interesting thing, my friend recalls. Instead of commissioning a hugely expensive study to try to predict the new patterns that would result from the opening of the new buildings, rather than devising an anticipated program and laying out a new scheme, the university’s brain trust decided to let the students and faculty, the lifeblood of the university, shape their own arterial flow.

Radial-arm saws, sliding compound miter saws, and powered miter boxes (chop boxes) used for crosscutting long boards are best located against the longest wall of the shop, as shown in the first option in the illustration. If the saw is to become a stationary machine, it’s typical to mount or build it into a long, narrow support table fitted with a fence.
×