I really appreciate the article. I am always looking for a way to improve my shop and its layout. I currently have a 34′ x 28′ garage which I park two vehicles and still have some room for a table saw, large bench and various smaller benches and cabinets. All of my large power tools are on casters so I can roll them out when I move the cars outside. Right now I am considering keeping my little truck outside permanently and set the shop up more in a fixed layout. This would make working in the shop more enjoyable and much easier to do more complex projects that I currently take on. Maybe this spring. Thanks for the advice.
I wanted to have numerous outlets, and have enough electrical service that I did not have to worry about overloading circuits. There was already some lighting, so I simply picked off that line and added additional lights to keep things bright and cozy. I ran a 240V line for the table saw and jointer with a dedicated breaker. For wall outlets, I ran 14-3 wire, and split all the plugs, so that I can run one machine on the upper plug, and another on the lower plug of any outlet.
I have found that drawing everything to scale on grid paper is most helpful. That is what I am doing in preparation for my new shop. I will, however need to share that space from time to time with my wife’s hobby (hatching and raising chickens). Just a few in the spring till they get big enough to go outside. I am planning on a 26″ x 40″ building with infloor hydronic heat. Others have mentioned that you can’t have too much light, and I intend to use the 200 watt cfl’s to accomplish this, along with task lighting at each machine. Walls and ceiling will be painted white to reflect as much of that light as I can. I want to use the same type of floor treatment that Marc has used in his new shop. Marc, is it really expensive to do that? Or if a guy has never done that would it be better to hire out that job? Lumber storage I have not decided yet. I am fortunate that I am able to fell trees on our farm and have them cut up so I can stack and dry them. We have white oak, red oak, maple, cherry and pine. Although drying/storage will be in another building will still have to tote my boards around some.
If your shop lacks wall space or doesn’t have a long enough wall to accommodate long stock, another option is to place the crosscut saw near an operable doorway with the right-hand side closest to the door (see option 2 in the illustration). This leaves most of the length of the fence to the left of the blade (preferable if you’re right-handed), allowing short and mid-sized parts to be cut to length or trimmed without having to open the door.
Lumber storage is spot on, I think especially for a basement shop – I used to store my lumber at the furthest point from the outside door, and it wasn’t until I moved it closest to the door that I realized how much of a difference it could make. And sheet goods are starting to be stored and broken down in the garage more so I don’t have to fight them into the basement.
Natural Light. Natural light is best, so any windows that offer illumination to the space should be put to good use. If you have little sunlight in your shop, locate your workbench so that its work surface gets whatever there is. Even the best eyesight is made better by good light, so the close work to be done on a benchtop benefits from the natural light.
When it comes to woodworking for beginners, I think it’s important to just learn how to use a few of the most essential woodworking tools for beginners. There are so many awesome tools available on the market today, it can be quite overwhelming as well as expensive to try to buy them all and know how to use them. Once you learn the basics of the most essential tools you will be able to start building in no time and feel comfortable learning any other new tools in the future.
Let’s face it, one of the most significant costs of your shop will be its foundation. While you’re at it, what about adding space above your shop? There may be regulations preventing you from building living space above your shop if it is in an urban setting or in an outbuilding, but there may be some flexibility depending on where you live. It is in the municipality’s interests to encourage infill housing that uses existing infrastructure. At a minimum, think about including attic trusses to create some space above your shop for drying lumber or storing equipment. Access could be from simple pull-down attic stairs or from the exterior if you don’t want to lose floor space to a stair or ladder. If you’re creating an addition to your house, you may be able to add a couple of rooms you’ve always wanted, such as a family room, office or in-law suite.
I place the band saw first in my order of purchases, because I consider it the heart of the shop. Band saws are very safe tools for ripping, re-sawing, cutting curves and more because all of the force is downward, virtually eliminating any chance of unexpected kickbacks. I wanted a saw that had a strong back, dynamically balanced cast iron wheels for smooth operation and flywheel effect, 12" depth of cut, good dust extraction design, a large table and a solid fence. After shopping around, I settled on the General International Model 90-170 14" saw. It is very smooth, comes with an Excalibur fence, and it is light enough (133kg) to move into your basement without crushing someone.