A little different from the others, the Wood Shop is geared more towards the “self-helper.” Take the three-hour safety class, available every Saturday, to earn your qualification card. You can then utilize the shop to work on your own projects. A wonderful variety of wood working equipment is available for customer usage for a very reasonable fee. Be sure to check out the available classes where you can learn to make pens, boxes, decorative cutting boards and even rocking chairs. We also produce custom order items to include coin holders, specialized plaques and shadow boxes.
Clamping up four mitered corners is tricky. You can buy specialty clamps for this, but I make my own. Here’s how to do it. Start with a long 1×4, as it’s easier (and safer) to clamp for making the angled cuts than a short piece. Mark out the blocks, and then drill a 1-in. diameter hole in the center of each one. The hole prevents the blocks from getting glued to your project. Cut 45-degree angles tangent to the hole, and then cut the blocks free from the long board. We’ll walk you through how to make one for your home shop.
Sanding concave molding doesn’t have to be difficult. Find a deep socket that fits the contour of your molding. Wrap a piece of sand- paper around the socket and hold it in place with your fingers. Your sanding will be uniform and the delicate edges of the molding won’t round over. — Eric and Cheryl Weltlich. In this video, Travis talks about his favorite sanding tips.
YP - The Real Yellow PagesSM - helps you find the right local businesses to meet your specific needs. Search results are sorted by a combination of factors to give you a set of choices in response to your search criteria. These factors are similar to those you might use to determine which business to select from a local Yellow Pages directory, including proximity to where you are searching, expertise in the specific services or products you need, and comprehensive business information to help evaluate a business's suitability for you. “Preferred” listings, or those with featured website buttons, indicate YP advertisers who directly provide information about their businesses to help consumers make more informed buying decisions. YP advertisers receive higher placement in the default ordering of search results and may appear in sponsored listings on the top, side, or bottom of the search results page.
Some types of wood filler can be hard to get off your hands after they dry, especially if you use your fingers to push it into small cracks and holes. When that happens, I reach for fine grit sandpaper and sand it off my fingers. It’s great for removing dried-on polyurethane glue and canned foam from your hands, too. — Chris James. We’ve got great solutions for removing super glue, too.
A while back, I reached for my two containers of epoxy and noticed that the resin in one container had crystallized exactly like honey that’s been in the cupboard too long. The solution is exactly the same too: Set the container in a bowl of hot tap water. After about 15 minutes, I emptied the container and refilled it with hot water. After about a half hour, the epoxy regained its normal consistency. Good as new! — Ken Holte
Click the image at right, and start building the ideal workflow at the bottom where you see the first red arrow. This arrow crosses through one roll-up door of a typical two-car garage. Note that if the right-hand window were not present, you could place lumber storage closer to the entrance, which would also allow for easier passage onto the jointer. Work flows from the jointer to the planer and the table saw, then ideally onto an outfeed table near position #2 in the diagram. From #2, proceed left to the assembly area (pictured below).
My planer blasts shavings all over the shop floor. I decided to make my own dust chute from 4-in. PVC sewer pipe (which has thinner walls than regular Schedule 40 pipe) and a couple caps. I cut a slit in the pipe and used a heat gun to soften the plastic. That allowed me to open the slit. (Heating PVC releases fumes; ventilation is critical.) I then drilled holes in the flap and screwed it to the planer housing. Finally, I cut a 2-1/2- in. hole in one of the end caps to accept my shop vacuum hose. Works great! — Luis Arce. Here’s what else you can do with PVC pipe.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking. These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email email@example.com and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence.
My hand tools are stored in a cabinet built into my bench but my shop supplies, air tools, and a plethora of “misc stuff” is in a cabinet on the other side of the shop, and my clamps are mounted on a wall adjacent to my bench, where conventional wisdom says tools should be. I just like it that way. I run my DC overhead and drop down… because my floor is on a slab. My bandsaw is mobile so I can pull it out of a semi-alcove for resawing, otherwise it stays in place for small operations (20″ bandsaws are cumbersome to move, even on leveling casters).
A landscape designer friend of mine tells a story about the college he went to. During his years there, the university embarked upon an ambitious building plan, adding several large structures around the main quad: a dorm, a chemistry lab, and a couple of others. The look of the place, which had remained unchanged for a century, was suddenly transformed, as glass-and-steel modernist structures were interspersed with the earlier ivy-covered stone Victorian-Gothic.
A board is considered “quarter-sawn” when the growth rings run, more or less, perpendicular to the face of the board. Quarter-sawn boards generally have straight grain and are less prone to shrinkage, compared to other boards. These factors don’t come into play with the 2x4s you use to frame a closet—but it does with the shelves and cabinetry you put into that closet; you want those boards to remain straight, flat and stable.
You have a few options for planning your shop space: The first is simply to photocopy the two-dimensional models and use them to create a scale layout of your shop floor. You also can go to my Web site (www.yda-online.com/shopmodels.htm) and download two-dimensional images of each tool to be used either on paper or on the computer. As a third alternative, you can download the same modeling program I used, and create three-dimensional plans.
Tired of waiting for finish to dry on one side before finishing the other side? You can purchase standoffs, but it’s also really easy to make them yourself. Simply drive 2-in. drywall screws through 2-in. x 2-in. squares of 3/4-in. thick stock. The screw points will leave a divot in the finish that can be touched up later, but I always let the back side of my project rest on the screws while the finish dries. — Matt Boley. Plus: Check out these 32 other handy hints for frugal shop rats.
Next come two options for the table saw’s trusty sidekick, the jointer, as well as for the thickness planer. Because it’s usual to work between all three tools when dressing lumber, the first option, shown in the illustration, locates the jointer nearest the saw to the right of its extension table with the planer nearby. As with the table saw, it always makes sense to align these tools with the shop’s long axis.