Once the workshop location is determined, it's time to begin planning how to lay it out. First, acknowledge the need to formulate a plan that's realistic in terms of the space allotted. The size of the structure or workspace will place some constraints on how much can be done. Taking into account size limitations, begin fashioning a plan that keeps efficiency in mind.
Efficiency does not always increase with experience, because as our woodshops grow older, they sometimes become unnecessarily rearranged or cluttered. And if you’re just now setting up your first woodshop, this shop layout should give you a great starting point. Each picture represents one half of a standard two-car garage. Click on the images for a larger view, and if anything is unclear, ask a question in the comments field!
Here’s an easier way to stain or seal chairs, lattice or anything with numerous tight recesses. Pour the stain into a clean, empty spray bottle ($3). Spray the stain onto the project and wipe up the excess with a brush or rag. The sprayer will squirt stain into all those tight, hard-to-reach cracks and joints. — Valrie Schuster. Learn more about staining wood.
Iron-on edge-banding is a quick way to cover up an edge on plywood. Trimming the excess, however, is tricky. I’ve tried edge-banding trimmers, but I find the results are unpredictable. With the trimmers I’ve tried, it wasn’t easy to change the direction of the cut to suit the grain direction of the edge-banding. If you’re cutting against the grain, you’re likely to tear out a chunk of your new edge-banding. Instead, I use a wide, sharp chisel. This way, I can read the grain direction and trim accordingly. Angle the chisel slightly and go slow, raising the back corner of the chisel just enough so that it doesn’t dig into the plywood veneer. Smooth the corner with a sanding block after trimming. Check out this amazing edge band veneering project!
I am also very tempted by the 10% package discount for combining the MFT/3 with the TS 55 REQ. …BUT: I already have a home-made workbench: 24″ x 62″ with 3/4″ bench dog holes in the double layer MDF top. It has a Jorgensen quick-release vise. {Copied from FWW’s “Getting started in woodworking” videos.} The only other work surface I have is a sheet of Melamine used as a router table (and is always cluttered with tools until I build some tool cabinets soon – hence the interest in LR32 & guide rail).
I am also very tempted by the 10% package discount for combining the MFT/3 with the TS 55 REQ. …BUT: I already have a home-made workbench: 24″ x 62″ with 3/4″ bench dog holes in the double layer MDF top. It has a Jorgensen quick-release vise. {Copied from FWW’s “Getting started in woodworking” videos.} The only other work surface I have is a sheet of Melamine used as a router table (and is always cluttered with tools until I build some tool cabinets soon – hence the interest in LR32 & guide rail).
This site uses affiliate links. Given this, please assume that any links leading you to products or services are affiliate links that we will receive compensation from. However, there are millions of products and services on the web, and I only promote those products or services that I would use personally. The Wood Whisperer abides by word of mouth marketing standards and holds integrity in the highest regard. Should I ever be compensated to write, I will make full disclosure. I always give honest opinions, findings, and experiences on products. The views and opinions expressed on this blog are purely our own. Any product claim, statistic, quote or other representation about a product or service should be verified with the manufacturer, provider or party in question. All content on The Wood Whisperer is copyrighted, and may not be reprinted in full form without my written consent.
The rubber cushion on my old palm sander was wearing thin around the edges. Because of its age, I couldn’t find a replacement pad. As I was drinking my beverage with a foam can cover around it, I realized I could cut the foam to fit the sander and glue it on. I peeled off the old pad, cleaned the metal base and attached the foam with contact cement. Works for clamp-on as well as stick-on sanding squares! You can find can covers at discount and convenience stores. — Allen J. Muldoon
Temperature and Moisture Control. If your workshop is to be located in a portion of your house that is already comfortably warm, this will not be an issue. But if you’re converting a barn or shed or an unheated space, especially if you live in a climate where winter temperatures make for cold hands, you’ll need to devise a heating strategy. In some climates, air conditioning is a virtual necessity in hot weather.
While trying to trace an exact copy of the throat plate for my table saw, I came up with this nifty technique using an ordinary pencil. I just shaved my pencil into a half-pencil by carefully grinding it on my belt sander. The flat edge enables my modified pencil to ride straight up along the edge of the template. It also works great for marking and then shaping inlays for my woodworking projects. — Tim Reese. How to cut circles with a band saw.
One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at $50/sheet.

When it comes to woodworking for beginners, there are 6 things that I think are essential to know for how to start woodworking. I’m going to discuss each of these tips in hopefully a really simple way to make it a breeze to understand, so you can get to the fun part of actually starting to woodwork! I wish when I started and was learning how to woodwork that I had a simple beginner tips guide like this one!
When cutting full sheets with my circular saw, I use plastic shelving units as sawhorses. The height is just right and by using three of them, I can make cuts in any direction and the plywood is fully supported. And because the shelving units are made of plastic, I can cut right into them without worrying that they’ll damage my saw blade. Plastic shelves are available for $20 at home centers. — John Tinger. Check out these tips for making long cuts with a circular saw.
Among early finds of wooden tools are the worked sticks from Kalambo Falls, Clacton-on-Sea and Lehringen. The spears from Schöningen (Germany) provide some of the first examples of wooden hunting gear. Flint tools were used for carving. Since Neolithic times, carved wooden vessels are known, for example, from the Linear Pottery culture wells at Kückhofen and Eythra.
Some types of wood filler can be hard to get off your hands after they dry, especially if you use your fingers to push it into small cracks and holes. When that happens, I reach for fine grit sandpaper and sand it off my fingers. It’s great for removing dried-on polyurethane glue and canned foam from your hands, too. — Chris James. We’ve got great solutions for removing super glue, too.
If your shop lacks wall space or doesn’t have a long enough wall to accommodate long stock, another option is to place the crosscut saw near an operable doorway with the right-hand side closest to the door (see option 2 in the illustration). This leaves most of the length of the fence to the left of the blade (preferable if you’re right-handed), allowing short and mid-sized parts to be cut to length or trimmed without having to open the door.
×