Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
For the next step up in convenience, consider adding a dedicated beverage cooler to your workshop as well. Though many people set up an old refrigerator in the garage for extra soda and beer, a dedicated mini-fridge will help you save on electricity, since new models are far more efficient than old ones. You can pack your beverage cooler with your favorite soft drinks for a pick-me-up while you work or use it to store a lunch to enjoy on a break —all without tracking dirt and or grease into your clean kitchen.
An interesting variation of this layout is displayed in Jim Tolpin’s shop, shown in the photo at right. Tolpin located his jointer to the left of his table saw, its height low enough to allow panels cut on the saw to pass over the jointer. To save space, his portable planer lives beneath the saw. All three tools are oriented toward the garage-style door, which can be opened to allow long boards to be ripped, jointed, or thickness planed.
To make sure you account for any existing obstructions, it’s a good idea to make a measured drawing of your workshop area on graph paper, noting existing furniture, built-ins and large items on the plan as you go. For example, a common one-car garage workshop layout has built-in tool cabinets and shelves around the perimeter where they won’t impede parking, but you may also have to get clever about folding work tables and saw horses that you can set up as needed in the middle of the garage when you’re working on a project (and cars are parked outside).
Click the image at right, and start building the ideal workflow at the bottom where you see the first red arrow. This arrow crosses through one roll-up door of a typical two-car garage. Note that if the right-hand window were not present, you could place lumber storage closer to the entrance, which would also allow for easier passage onto the jointer. Work flows from the jointer to the planer and the table saw, then ideally onto an outfeed table near position #2 in the diagram. From #2, proceed left to the assembly area (pictured below).
Natural Light. Natural light is best, so any windows that offer illumination to the space should be put to good use. If you have little sunlight in your shop, locate your workbench so that its work surface gets whatever there is. Even the best eyesight is made better by good light, so the close work to be done on a benchtop benefits from the natural light.

Clamping up four mitered corners is tricky. You can buy specialty clamps for this, but I make my own. Here’s how to do it. Start with a long 1×4, as it’s easier (and safer) to clamp for making the angled cuts than a short piece. Mark out the blocks, and then drill a 1-in. diameter hole in the center of each one. The hole prevents the blocks from getting glued to your project. Cut 45-degree angles tangent to the hole, and then cut the blocks free from the long board. We’ll walk you through how to make one for your home shop.
I use binder clips for a lot of things around the shop, and here’s one that I thought I’d share. When I need to make multiple cuts all the same length, I just clamp my jumbo binder clip to my fence and use a 1/4-in.-thick wood scrap pinched in the clip as a stop. Works like a charm! When it’s not in use, I clamp it to the cord so it’s always nearby. — John Muchow
With the advances in modern technology and the demands of industry, woodwork as a field has changed. The development of Computer Numeric Controlled (CNC) Machines, for example, has made us able to mass-produce and reproduce products faster, with less waste, and often more complex in design than ever before. CNC Routers can carve complicated and highly detailed shapes into flat stock, to create signs or art. Rechargeable power tools speed up creation of many projects and require much less body strength than in the past, for example when boring multiple holes. Skilled fine woodworking, however, remains a craft pursued by many. There remains demand for hand crafted work such as furniture and arts, however with rate and cost of production, the cost for consumers is much higher.
Let’s be clear about one thing: No workshop is perfect for everyone. If there were, I could simply give you a precise plan to follow with clear dimensions. Every person who comes to the hobby, avocation, or profession of woodworking has his own particular collection of tools and his own peculiar work style, skills, and desires for the kind of woodworking he wants to do that gives him a unique approach as to how he will lay out a shop: where the tools should go, where lumber and supplies are stored, and how much bench area he needs.
×