The planners did an interesting thing, my friend recalls. Instead of commissioning a hugely expensive study to try to predict the new patterns that would result from the opening of the new buildings, rather than devising an anticipated program and laying out a new scheme, the university’s brain trust decided to let the students and faculty, the lifeblood of the university, shape their own arterial flow.
Use whatever image hosting service you like and post the link to /r/woodworking. The key here is it needs to be apparent that you've built the entry, and you follow the photo requirements listed in the contest rules. Submissions of finished photos only will not be accepted for entry. <-- I can't emphasize this enough, you absolutely need more than 2-3 photos for a valid submission. I will no longer accept entries that have albums that go from rough stock to 90% complete in one jump.
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strapping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.
The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.
In this video James Huggett shares a very detailed tutorial on how to cut a half-blind dovetail joint with hand tools, for use on drawers and case pieces. Jim has cut many dovetails over the years, and here are some of the lovely dovetailed drawers that Jim has made using this half-blind dovetail joint: Notice the deeply scribed layout line on these drawers. That, along with irregular and more delicate pins, are a sure sign
Since most of your assembly will be done on the assembly table, it just makes sense to have your clamps nearby. If you’re short on wall space, try a rolling clamp cart! If you use your workbench for assembly, keep your clamps near the workbench. Check out these two helpful articles for clamp racks: A Simple Utilitarian Clamp Rack and A Parallel Clamp Rack.
The rubber cushion on my old palm sander was wearing thin around the edges. Because of its age, I couldn’t find a replacement pad. As I was drinking my beverage with a foam can cover around it, I realized I could cut the foam to fit the sander and glue it on. I peeled off the old pad, cleaned the metal base and attached the foam with contact cement. Works for clamp-on as well as stick-on sanding squares! You can find can covers at discount and convenience stores. — Allen J. Muldoon
For our customers who are passionate about woodworking, we offer an extensive selection of tools and accessories to help your woodworking projects come to life. Whether you are a professional carpenter, construction manager or simply wish to build a DIY project, you will find everything that you need on our Amazon.com Woodworking page. Our selection ranges from, screwdriver sets to air filtration, band saws, sanders, drill presses, dust collectors, jointers, laminate trimmers, lathes, planers, benchtop, plate joiners, belt sanders, router combo kits, shapers, sharpener, barn door hardware, circular saws, router tables, router bits, planer, tool box, wood glue, nail gun, table saws, hammers and more.
YP - The Real Yellow PagesSM - helps you find the right local businesses to meet your specific needs. Search results are sorted by a combination of factors to give you a set of choices in response to your search criteria. These factors are similar to those you might use to determine which business to select from a local Yellow Pages directory, including proximity to where you are searching, expertise in the specific services or products you need, and comprehensive business information to help evaluate a business's suitability for you. “Preferred” listings, or those with featured website buttons, indicate YP advertisers who directly provide information about their businesses to help consumers make more informed buying decisions. YP advertisers receive higher placement in the default ordering of search results and may appear in sponsored listings on the top, side, or bottom of the search results page.
There are many factors to consider when deciding what type of wood to use for a project. One of the most important is the workability of the wood: the way in which it responds when worked by hand or tools, the quality of the grain, and how it responds to adhesives and finishes. When the workability of wood is high, it offers a lower resistance when cutting and has a diminished blunting effect on tools. Highly workable wood is easier to manipulate into desired forms. If the wood grain is straight and even, it will be much easier to create strong and durable glued joints. Additionally, it will help protect the wood from splitting when nailed or screwed. Coarse grains require a lengthy process of filing and rubbing down the grain to produce a smooth result.
In the above video Will Myers teaches the basics of woodturning for woodworkers. He starts by showing how to prepare and center the wood, then discusses woodturning tools & parts of the lathe. And finally he begins roughing out a spindle for a classic cherry shaker candle table. This tutorial comes from the class and DVD: "Building the Hancock Shaker Candle Stand with Will Myers". If you'd like to build this historical candle stand along
In most small shops, once the key machines are in place, others are arranged wherever there is room for them. There typically isn’t enough free space for these tools in the middle of the floor area, although sometimes you can tuck a machine into an unused space. For example, in a shop where the table saw is in the center, a shaper (or a router table or spindle sander) with a table the same height as the saw can be put on the outfeed side of the extension table (see the illustration). Also, building a router table directly into the table saw’s extension table is a great way to save space, as well as make use of the saw’s fence for routing operations.