Instead of using a container to mix a small amount of epoxy, just make a mixing surface on your workbench using painters tape. Simply lay down strips, overlapping the edges so the epoxy doesn’t get on your bench. When you’re done, peel off the tape and throw it away. This mixing surface will work for more than just epoxy, you can use it for wood glue or any other material you need easy access to while working on a project.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking. These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email firstname.lastname@example.org and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence.
When cutting full sheets with my circular saw, I use plastic shelving units as sawhorses. The height is just right and by using three of them, I can make cuts in any direction and the plywood is fully supported. And because the shelving units are made of plastic, I can cut right into them without worrying that they’ll damage my saw blade. Plastic shelves are available for $20 at home centers. — John Tinger. Check out these tips for making long cuts with a circular saw.
That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000.
A kind’a unrelated question. I just finished building the lumber storage rack/sheet goods cart from your “racking my brain..” video. I see you went with the metal wall storage rack in your new shop (which I would love also, just can’t afford) but, I was curious why you didnt put another sheet goods cart. Previously I had the stand up sheet goods storage box like I see your current pictures but, from what little I have used the cart, I like it better than the stand up storage. Its easier to get things in and out and see what all I have. The only draw back is that I can’t store as much on the cart as I could with the box storage.
Cutting thick, rough, warped hardwood can be cumbersome and dangerous. To provide some control over this process, I built a chop-saw station with wings that extend to support long boards. Again, anytime you make something that consumes shop space, make a shelf underneath to gain storage. The chop saw sits in a recess so that the deck of the saw is at the same height as the workstation deck.
Usually ducting is well covered and one of the first things considered, however, most people initially neglect clean up when designing shops. With growth, I have a very cluttered shop that makes pulling shop vacs around frustrating especially if you’re at the wrong end of a 5m flexible hose without having to struggle with the vac (the practice of in no doubt exacerbated by those ridiculous vacuuming ads on TV). As my setup is retro fitted, it may not be pretty as it is ducted overhead, but it is productive. I have a centralised heavy duty ‘shop vac’ (rigged with a Dust Deputy) and 50mm stormwater piping radiating to selective parts (corners) of the workshop. I use 50mm water diverters to act as blast-gates to control the flow of air (I have a bank of them running down one full side of the workshop spaced about 5m apart). When I need to clean a part of the shop I plug the vac into the appropriate overhead vent, organise the diverters and attach a 5m flexible hose to the working end. I have the vac on a remote (one of those that control power points – all my dust extraction is controlled by these – after modifying any proprietary mag switches) and I can vacuum any part of my workshop without having to go and manually switch the vac on. I have bought some cheap off market flexible hoses and spread them at the extremities of the workshop. Each outlet will accept the hose. Hint – I bought a fairly low end 3D printer ($800 (Aust)) and I can print any sized coupling to accommodate all those non-standard ‘shop vac’ hoses/fittings to accept my proprietary shop vac accessories. Duct tape is now reserved for the few threaded non-standard couplings.
Tape measure: I know this isn’t a power tool, but it is the one tool that you should always have with you. It is a pet peeve of mine – if you are planning on building something, or you are actually building it, have a tape measure with you. If you are in the shop, on the job site, or even at Home Depot make sure you have a tape measure with you or at least one very handy (Home Depot probably isn’t the best example, since they have them widely available, but you get the point). Without a tape measure, not much beyond rough work can get done.
This self-clamping table saw fence takes only seconds to put on and lets you crank the blade into the fence to create both angled cuts along board edges and extremely thin rip or rabbet cuts. With a hand- or jigsaw, cut pieces from a 1×4, making the inside width of the “L” a hair under the thickness of your saw’s fence. Drill 5/16-in. holes in the L-blocks and plywood fence and join them with two 1/4-in. x 3-in. countersunk machine screws, washers and Wing-Nuts. As always, use extra caution when you’re sawing without a blade guard. Our thanks for this new sawing angle to professional furniture maker George Vondriska. Check out these 16 genius tool hacks you need to know!
Let’s be clear about one thing: No workshop is perfect for everyone. If there were, I could simply give you a precise plan to follow with clear dimensions. Every person who comes to the hobby, avocation, or profession of woodworking has his own particular collection of tools and his own peculiar work style, skills, and desires for the kind of woodworking he wants to do that gives him a unique approach as to how he will lay out a shop: where the tools should go, where lumber and supplies are stored, and how much bench area he needs.